This is the Build Thread for 99 purple gsx. Reply below.

I have been attempting to reinstall my wiring harness on my 99 m/t gsx. I have ran into a few connections that I cannot find for the life of me. I have used https://www.dsmtuners.com/threads/2g-engine-bay-electrical-connections.298047/ to help me so far.This is part of the starter harness...

I found this sensor mixed in with a bunch of bolts. It looks like the connector is broken on the top, any idea what part this is?

I am in the process of removing the charcoal canister on my 99. I have removed the actual canister on the drivers side front bumper area and the hard lines running back to underneath the battery tray. I have encountered solenoids under the battery tray that I am not sure what to do with, also...

I have a 99 gsx. I have been away from dsm knowledge for about 5 years. I was all ready to go the eculink route until reading the 99 ecu is flashable. I also have a 95 eprom ecu somewhere.Anyway i am looking for some advice on which way to go from users of both. I know there is a huge...

Whats up guys. My car has 750cc inj, 42 psi fuel preasure, no boost leaks, 272 cams, 57trim turbo and ecu+ with other supporting mods including head studs. So after the cams, timing belt change the car started stuttering and misfiring whenever I revd it up past like 6k. I log it and the...

My friend with his gsx put on greddy intercooler pipes with a type s bov. He has a cone filter. He builds boost way too fast and too much for the stock boost solenoid. He will hit 20 psi easily and his car isnt really going anywhere. His exhaust manifold is missing one of the bolts and we...

Ok I called a reputable shop asking about cams and a limited slip dif for my 50trim gst. They told me that to take advantage of the cams I would need to rev to 8k and I couldnt just do cams. They said I would need head studs, yeah I know, but connecting rods? Maybe Im getting confused with...

I need a timing belt swap. So I am going to get a kit. I read there are 5 seals that I need to get along with the kit. What might they be? I want to get cams at the same time and was looking at the fp2x's but would the fp2's be close enough to tell a difference? Otherwise that requires the...

I have intake, rs49t, fmic, short route piping, hks bov, 3" tbe catless, evo3 manifold and 02 housing, 750cc injectors, 255 walbro, ecu+, fpr, act2600, you get the idea. what cams would be best for a track/street car? I was looking at 272/272s but maybe for my setup 264/272s would be better?

I have a 99 gst. I am looking to upgrade to the 2g awd brakes. If I can find a 95 set with the banjo bolt, calipers, mounting braket, shims, pads, and rotors, is this all I need? I have ss lines on the car already, will these work? I have 17" le37t's with a 42 offset. Will the brakes fit...

I have a forge unos mbc with an agp rs49t internal wg. I had the mbc turned all the way down with the soft spring and I was hitting 15 psi solid. I went to turn it up and it droped down to 10 and would creap up to 13. No matter how much I turned it up it wouldnt change. I put the stiffer...

Where can I get some exhaust hanger bushings? I need to replace a few on my 99 gst. Are there any stiffer bushings out there or should I just stay with stock?

My setup is...intake, agp rs49t, evo3 manifold and 02, rre downpipe, espelir catback, no cat, fmic w/ piping, hks bov, plugs and wires, walbro 255, fpr, boost gauge, egt gauge, act 2600, streetlite flywheel, I had a greddy spec2 ebc and turbo timer but they both just died. I have 750cc...

Alright well I installed my 50trim, fmic, yada yada. Ive had a greddy ebc and turbo timer on my car for 2 years and now the ebc has no power and the turbo timer is going crazy. Its constantly beeping and flashing random numbers. I hooked up my egt gauge finally and thats the only change I...

My current mods are filter, intake pipe, agp rs49t, fmic w/ piping and hks bov, greddy ebc, act2600 w/ lite flywheel, 255 fuel pump w/ regulator. I also have injectors sitting here but Im waiting on my tuning device. What maintenence would be good to look into as well as a tuning device and...

I would like to have some opinions on what to do next. Here is what I have either on the car or sitting here ready to get put on. apex filter, dejon intake hard pipe, agp rs49t w. lines, fmic w/ piping, hks bov, greddy profec b2, evo3 manifold ported, evo3 o2 ported, rre long downpipe, espelir...

I have narrowed my choice down to 2g gsx brake upgrade or the baer claw big brake kit. They are both 2 piston calipers with larger rotors. Would I see much of a difference with the baer kit over the gsx brakes? I have read that the gsx calipers have a different brake line connector, how would...

Currently on my car I have sloted/dimpled rotors, metal masters pads, and ss brake lines. I plan to track my car some and can already feel the fading on the street. I would like to upgrade to atleast a 2piston caliper and bigger rotors with a more aggresive pad. I was looking at a gsx upgrade...

I recently put an aeromotive fpr on my car along with a walbro 255. I have 750 cc injectors waiting to go on along with dsmlink and a rs49t. Will I run into problems if I don't replace the fuel feed line with a bigger ss line? I saw the kit on slowboy and was wondering if this would be...

I put an act 2600 in my car over 10,000 miles ago. When I push the clutch in it is not smooth and makes a squeeking sound. Also when engaging or just letting of the throttle fast it sometimes makes a clicking sound. What would this be? The clutch engages pretty good but sometimes just wont...

I have a 99 gst. I was cruising at about 60 and my car died. It rolled to a stop and everything was dead. I looked at the fuses and the ignition switch had blown so I swapped it for the power windows. I got my power back but when I tried to start the car it wouldn't turn over. It will crank but...

I have a 99 gst. I was cruising at about 60 and my car died. It rolled to a stop and everything was dead. I looked at the fuses and the ignition switch had blown so I swapped it for the power windows. I got my power back but when I tried to start the car it wouldn't turn over. It will crank...

I put on aeromotive fpr on my 99 gst. I also installed a walbro 255 fuel pump. I removed the stock fpr, attached a fiting on the right side of the fuel rail. Ran a line to the aeromotive fpr to the bottom of it. The fuel supply line is attached to the side of the fpr. My fuel preasure gauge...

Well I just got a rre downpipe w/o cat. Do I need to do anything to install this since there is no cat? What I mean is will the o2 sensors be screwed up and what will fix this?

Where can I get an adapter to mount an hks ssqv to either a greddy or 1g flanged uicp?

I plan to get dsmlink in the near future. Can it work with the maf-t on a 3" gm maf in a blow through setup? Also what is the absolute largest injectors I would need for an agp 50 trim?

I plan to get a pte 50 trim. What psi would I be able to run it at with tbe, fmic, 660's and an safc? Also what bov would best fit this recirculated setup?

I have a 99 gst. I am looking to upgrade my suspension but don't want to go with full coilovers. I have wheels that are 17x7.5 w/ 42 offset and need tires. What setups would be best and size tires with it for the street?

I am looking for a good tire for my 2g gst. The wheels are 17X7.5 w/ 42 offset le37t's. I am not looking to spend a great deal of money but want something with decent handling and traction. Also being a gst they will be spinning some so tread wear is also going to be accounted for. In the...

What is the easiest and best bov to use on a maft vented setup running a fully supported evo 3 16g?

My greddy type s lost all of its venting sound when I put on my dejon tool hard intake pipe. I have greddy pipes and it used to make a sound with the stock pipe but with the hard pipe it is almost completly quit even at a full wot vent. Is there anything I can do to regain the sound?

How is the top end on the big t28 compared to an evo3 16g? I know the t28 will have quicker spool but does it still slop off in the high rpms like the t25? I want a quick spooling turbo that will continue to pull all the way on the highway.

I have read people having problems with boost creep while using the E316G. I have a greddy profec b 2 and plan on getting and E316G with the 34 mm wastegate option and fully ported from slowboy. Would this be enough to control the boost or when I get my 3" 02 eliminator exhaust from rnr racing...

What would be the best and easiest logger to use with an safc2 on my evo3 16g.

What is the best exhaust setup for an e3 16g when replacing all? (manifold, o2 housing, downpipe, test, catback) I was looking at the rnr 3" o2 eliminator or would just the downpipe back with an evo3 o2 housing be better? Also which manifold would be best for the money?

Well my stock t-25 and valve lifters in my 99 gs-t need to be replaced. For my turbo I want something with quick spool but good power. I was looking at a 14b, small 16g, or t-28. Also get a 1gen head and rebuild it with cams and such. I dont want to upgrade my whole fuel system right away or...

I just put some projectors from an audi a6 into some aftermarket projector housings and they are aimed way too high! I have tried adjusting them and they still are blinding. Anyone know a fix or should I just bend the brackets that hold the hids so they face down?

Everytime I get on the gas my car sputters. It sounds like something is spinning and rubbing so I'm guessing its my turbo going. Im on the stock t-25 and I have 53k on a 99 gs-t. Also when I just tap the throttle my car chirps sometimes. could these be the same thing?

What am I supposed to do with the stock wastegate solenoid after i have installed my greddy spec 2 controler? Do I unplug it and take it out? or plug up the ends or just let it flow?

When I let off of the throttle while accelerating hard my car stutters and shakes violently back and forth suddenly and stops. I believe it happened after I moved my greddy electronic boost controler remote that is in the engine bay. I mounted it to the head and chaged the 6mm tube to a 4mm...

Slowboy sells a 2g MAF with 2.5" piping which includes 2.5" intercooler pipe, MAF translator and the 3" GM MAF. Is there anything else needed to run this setup other wise a bov and new intake pipe?

I believe I read somewhere about the process to retrofit audi a6 projectors into projector headlights for the 2g eclipse. For some reason the search function isn't returning any results at all for me so could someone please post the link? Thanks

Is it possible to do an hid projector conversion in 97-99 headlights with halos or will it not work?

I have a set of volk le37t that were currently on an integra type r. The washer/disk in the center of the wheel that is able to be poped out does not fit with the front wheels. Can I buy this piece and does anyone know where I can get it?

When installing the satelite radio you need to use an antena. How do you mount the antena without a cord running inside of your car? Can you hook it up to the factory? thanks I dont know much about audio stuff

Does anyone have any experience/opinions with these projector headlights? http://www.matrixracing.com/BI5220Details.htm How is the lighting quality? Are the halos the main source of light or do they only light up with the side lights? Would these be good for an hid retrofit or would non halos...

Somtimes when on boost or not when I let off the throttle the car bucks back and forth a couple of times. I recently installed a greddy profec b 2 on my car and it started to happen after the install. What I think it is has to do with the hose going from the control box to the wastegate...

What is the threading on the lugs on a 99 gs-t? 1.5 or 1.25? Also will wheels that are 17X7.5 with a 38mm offset fit?

When hooking up the greddy type s do I put the T fitting, im guessing for the boost reading, in the fuel pump preasure or do I put it inbetween the bov and intake manifold? or somwhere else?