The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support JNZ Tuning
Please Support Fuel Injector Clinic

Search results for query: *

  1. Building a new computer - need ideas

    I have around 1500 to spend on a new computer. My goal for the computer is internet, word processing/spreadsheets, music, watching movies, connecting my video camera to the computer to download video and make my own movies, play mp3's from the computer into my home stereo, gaming, email, and...
  2. FP Gauge Install

    does the FP Gauge get installed before or after the fuel rail. I thought you tee'd off the vacumn hose from the FPR to the FP solenoid on the car.. the blue dotted vacumn line
  3. 16s on a 97 GSX?

    I'm looking to downsize from a 17" to a 16" mainly because I like the Rota Attacks.I don't think my 2piston calipers would allow me to do this.. could i use the single piston from a gs-t or would it not bolt up right?Thanks!
  4. are any of these illegal to have..

    Are any of these mods illegal to drive on the street with? (Meaning having to worry about cops)Aftermarket seats w/ 4pt harness Fuel Cell instead of stock fuel tank
  5. new motor - cranks, combusts, dies..

    ok, i have a 6bolt swap in my 2g.. i don't have any hoses on my tb connected because i blocked off the egr for now until the car runs good.. map sensor is plugged in but not mounted on the intake manifoldi'm getting fuel and spark looks like.. the car cranks, starts and revs to 400 and...
  6. cas adjustments

    Ok, i'm starting my 6bolt swap for the first time and I want to know where to position the CAS so it idles somewhat fine.. should i leave it in the center, or more to which direction?thanks
  7. timing..

    i was wondering why you need a timing light if our cars are distributorless?All i see is a coil pack - no cap/rotor.. so what good does a timing light do if the ecu just advanced/pulls timing on its own?
  8. compression tester gauge..

    i have a Compression tester gauge.. i was wondering if I could use it to measure oil pressure while I start the car.. i know i won't be driving with it, but just to see if I have oil pressure when I start the new motor.
  9. few easy questions 1g throttle body on a 2g

    when swapping to a 1g throttle body on a 2g, the sensor with a little peice of metal coming out, do you not plug in anything there? i have the ISC and TPS hooked up. There are no wires in my harness to plug anything into there.Also, on my 1g water neck (6bolt swap), there are two sensors it...
  10. side of engine

    does anyone have pictures of the crank side of the engine. i want to see how the belts are positioned and the water pump pulleys, etc. I can't figure out how my belts go on. Now someone tells me the water pump has 2 pulleys?its a 6bolt motor going in a 2g eclipsethanks!
  11. OFH - oil feed lines

    I believe I have a 1990 oil filter housing.. I don't see any spots where I can attach an oil feed line from that goes to the turbo..
  12. gauge cluster

    if i remove my gauge cluster in my 97, will affect anything on the ecu or car itself. I want to put my own custom gauge cluster in and have it molded in place.I hear on the 1g's you can do it, but i can't find any info for 2g'sI want to try and fit a tach, speedometer, oil pressure, oil...
  13. fastest with this setup

    what's the fastest 2g AWD on an ACT 2600 pressure plate with street disc? Just trying to figure out if i should sell my 2600 for a 2900 if i'm looking to run mid 11's.I did a search and found a chart, but it only lists names and 1/4 mile times, not what drivetain, so don't flame or bi***!
  14. how's this for drivetrain mods

    ACT Streetlite Flywheel New OEM flywheel bolts (loctite) ACT 2600 w/ street disc Revised OEM clutch fork New Pivot Ball Stainless steel clutch line New OEM slave cylinder New OEM master clyinderlooking at around 500whp... you think it should handle it? FP3052 turboI keep hearing...
  15. manifold sensor

    I'm swapping the 2g intake manifold to the 1g manifold. I noticed there is not spot on the 1g for the absolute manifold pressure sensor. Its mounted on the very top of the manifold in the center. Did you guys relocate it or didn't hook it up
  16. sensors for swap

    I have a 1997 GSX and i'm dropping in a 6bolt i just built next weekend. I have a 1g throttle body, a 1g intake manifold, 2g tbody elbow, evo III exhaust manifold, 2g o2 housing, stock t25 turbo (YEAH I know!)I swapped my TPS sensor onto the 1g throttle body, i also cleaned it out with some...
  17. laws about motor swaps

    What are the laws regarding motor swaps. I have a 2g with a 91 6bolt. I'm guessing its illegal, but what if it passes emissions?How does it work when a dealer puts a new motor in under warranty. Technically the VIN's are different anyhow, right?Just curious.
  18. changing

    I think i'm getting tired of my GSX, possibly looking to getting a different car. I've been building this car since March and i'm just tired of it. I want a car that runs and that's reliable. Any of you guys have the same problem?
  19. greddy - emanage

    anyone have it and like it? I was thinking of using it for a 1g motor in a 97 GSX.Does anyone have a full list of features.. the greddy site is down right now.Just comparing Greddy vs DSM Link vs SAFCII vs GM MAFTThanks..
  20. Do I have everything I need?

    Ok guys, everything is coming back tomorrow and i'm doing the 6bolt swap in my 97 GSX over the weekend. Just want to make sure my checklist is A okay!Here goes:Complete rebuilt, ported/polished head and 4 angle valve job (SI 1mm oversized nitrate coated valves, Crower Valve Springs...
  21. which would you prefer?

    Ok, everything is being assembled as we speak. My only concern now is which piggy-back to go with..?I was thinking either dsm link or ecu+.right now i'm running the t-25 still w/ a built motor.. yeah i know, i need to buy a new turbo (just using it for break-in) and i'm still using...
  22. gauge cluster

    is is possible to remove the stock gauge cluster and just have a custom one placed inside with autometer gauges - will it effect anything?
  23. pistons/rods

    i'm having trouble putting the wrist pins through the piston with the rod in it.. i used assembly lube and it isn't making it too easy.. can i lightly tap it in?also, the little clips or whatever, how do i put them in the piston where they are supposed to go.. i can't compress them enough...
  24. what does it take

    how fast can 400whp on a gsx get you on a 1/4 mile with a stripped interior?my friend swears he can do 11.9's
  25. valvetrain

    What is your valvetrain setup? (valves, valve springs, retainers, etc)
  26. oil pump, water pump, etc

    When I got the 6bolt block, there was a crack on the front case. So I need to get a new one. I was wondering what else I would need. Does the front case come with an oil pump, or is it seperate? Should I get a new water pump while i'm at it too? What are all the gears, tensioners, etc that I...
  27. koni/gc - tuning?

    Ok, I'm going to be receiving my Koni Yellows on Tuesday. I'm looking to just get the ground control perches and plates and use hypercoil springs as recommended by others.My question is, how do I set the ride height in the vehicle. If I make the fronts and rears match, wouldn't it get thrown...
  28. injector size

    2g with a 6bolt swapross 8.5 pistons eagle rods 272/272 hks cams fp 3052 turbogoal is to run mid 10's.. what size injectors do you think I would need.. 7 series or 8 series? or bigger?
  29. EXEDY Cerametallic Clutch

    anyone have experience with this clutch, i have awd and looking to run in the 11's down the trackEXEDY Cerametallic Clutchi'm not looking to go alot, i'm also going go get a lsd for the center diff
  30. 2G Trouble pulling the axles

    i'm having trouble pulling the axles out of the transmission on my 97 awdi got the axles out of the wheel hub so far..
  31. springs/shocks

    ok, i have decided to go with the koni yellows for their nice damper adjustment. I know you can change the ride height also on the shocks by setting the plate higher or lower where the spring sets on.. its not much of an adjustment.. but its a good feature i guess.My question is, I want a...
  32. tein flex w/ edfc

    for 2g GSX... is this setup good, any experiences? am i wasting my money- what other combo's are both hieght/damper adjustable. looking for a nice ride but able to stiffen for track/autox
  33. wheel size

    is 225/45/18 or 235/40/18 good, like will it fit my car. Its lowered about 1.5" and i might consider lowering it more. What is the minimum offset i can use? I don't want to rub. I think 225/45/18 would be better as far as fitment
  34. help

    ok, track is opening up, my goal is to be able to run 13.5i ran a 14.4 last season with apexi gt downpipe/exhaust, and air filter. My problem was the stock bov was not holding boostso this season, i'm getting a bov, intercooler piping, and what other stuff can i get to run a 13.5 - i...
  35. engine state of tune?

    I'm going to be installing my Stage 2 Crower Cams, Valves, Valve Springs in about 2-3 weeks once they come in. Not sure how to build the bottom end: 95 pistons w/ 1G Rods or Crower pistons and rods.My other question: I have a 2g and swapping a 1G in there w/ DSM Link. So I need the EPROM...
  36. gasket

    what valve cover gasket do i get for my valve cover on a 2g turbo?i'm at dsmparts.com right now looking up gaskets..there's a main valve cover gasket half moon gasketwhich ones do i need, just curious and any tips on putting one on would help :)
  37. black seatbelts

    does anyone know if black seatbelts on a 2g were ever made? I called about 30 junkyards and all they have is gray and tan - so i was thinking either black interiors don't come too often to junk yards or they don't make them in black.. the dealership said they came in black in 99..i have a...
  38. ignition cut-off

    Where's a good spot to put a switch to cut off the ignition. I know I can put it where the steering wheel is because the wires are all there, but if a theif looks there, he can simply jump the wires..I was thinking of tapping it someplace under the hood by the ignition coil, which wire do I...
  39. fuel pump rewire

    ok, i ran a wire with an inline fuse all the way to the fuel pump and now i'm stuck on what to do.. i checked the forums and searched, but could not find anyone who did it on an awd 2nd gen dsm... i tried using the 97 gst rewire, but my plug has like 6 wires going into the plug and the other guy...
  40. anyone have pics of this

    I'm trying to find pictures of a white 2nd gen with gold wheels.. just want to see how it looks..thanks for posting!
  41. gauge face

    does anyone have a picture of the circuit layout for the 2g gauge cluster and the location of each bulb that lights the gauge and which led's do you need to change the orange to blue..thanks!
  42. turbocharger upgrade question

    I'm deciding on which turbocharger I should get. I plan on doing the fuel upgrades such as fuel pump and rewire, fuel injectors, and a fuel management system, i also have the full turbo-back exhaust and air filter - my goal is to run 11-12's on the street with pump gas. which turbo will best get...
  43. is this bad?

    i did a compression check about an hour ago.. when i pulled off the spark plug cover, i noticed a good amount of oil sitting there. I also noticed when i pulled the spark plugs out, that they were black - i guess my car has been running real rich.when i did a comp test, my compression was...
  44. interior panels

    what's a good paint to use to paint interior panels. i want to change my panels from gray to black?Also, I was thinking of laying fibre glass over it and then painting it..which way should I go?
  45. need help with this

    My first problem is my car smokes alot after i've been idling for over 2-3 minutes. Its a white smoke. My temperature gauge reads normal so i'm not overheating and i'm guessing the water pump is still fine? I'm running a full turbo-back exhaust system w/ no cat - APEXi GT DP/Catback. Does anyone...
  46. a/f ratio gauge

    i hooked up my a/f ratio gauge and it seems to read very rich whenever i'm on the gas, and very lean at idle... when i vent into the air it goes stoich, then lean, then back to rich when i put the gas pedal down.is this how its supposed to be? shouldn't i be leaning out as i wind out the...
  47. 2G legal to change steering wheel?

    does anyone know if its illegal to remove the stock steering wheel and replace it with an aftermarket - non-equipped steering wheel?thanks
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top