I have a 95 Eclipse GST and im having trouble figuring out why it wont start, this is what i have done to try to troubleshoot it so far:1. I changed the coolant temp sensor cause the scanner said it was bad and the CEL turned off but still didnt start.2. Changed the MAF cause the one...

I am installing an SCE copper head gasket on my 98 eclipse GST with ARP head studs. I was told to torque studs to 65 ft. lbs and to not exceed 70 ft. lbs. Are thes torque specs about right? Has any anbody ever used a copper head gasket?

I recently did my timing belt and installed all new components from Mitsubishi, after only 700 miles the Idler Pulley is making a squeeky noise and appears to be wearing down my timing belt, there's blue paint all over and around it from my Greddy timing belt. Anyone know what would cause the...

Is there a way to check a rear differential to see if its good? The one on my friends 95 talon is going bad and we found a car at the junk yard that has it and we wanted to make sure it was good before bying it.

I was torquing down the cam caps after getting the head rebuilt and one of the cam cap holes is stripped and I can figure out how to fix it, there is a guide for the cam cap that the bolt goes through to aling the caps, how would I go about fixing it? I bought a Helicoil thread repair kit that...

Just thought I'd post some pics from when me and my friend were swapping heads on my eclipse.Old Head (2g) 1. http://img26.picoodle.com/img/img26/9/9/5/trboeclpse98/f_S6000695m_d18b880.jpg 2. http://img34.picoodle.com/img/img34/9/9/5/trboeclpse98/f_S6000691m_fb11250.jpgNew Head (1g)...

I have a 98 eclipse GST and i am looking around for front mount intercoolers and was wondering what was the largest size intercooler i can install without having to move or cut anything?

I have a 98 eclipse GST and i am looking around for front mount intercoolers and was wondering what was the largest size intercooler i can install without having to move or cut anything?

Anyone know if the 1g prothane motor mount inserts for transmision and timing mount fit the 2g motors mounts?

I just ordered a set of the Brian Crower 272's and I was wondering if the intake cam has to be drilled and tapped to fit the 97-99 Cam Angle Sensor (CAS)? I emailed Brian Crower and asked him about this and his reponse was...

I just bought a Garrett t3/t4 at a very good price, but I don't know if it will be worth even bothering to install it on my 98 eclipse gst. I'm looking for 12 second 1/4 mile times with the mods listed in my vehicle profile, just upgrading my injectors to Evo VIII 560cc injectors and either...

What size are the stock injectors on an 2005 Evo VIII? Will they fit a 2g 4g63t? Are they a direct replacement or would I need to modify anything?I can get a set of them really cheap from an Evo guy that is upgrading.

New to tuning and logging, I just installed a MAF Translator set to 470cc injectors on stock injectors to lean it out a little bit because it was smelling like gas fumes when it was set to 450 or 460. Everything else is zeroed out. According to this log, how is my car running?

I installed a 1g 63mm throttle body on my 98 eclipse gst and now my idle is between 1800-2200 RPM. I already tried adjusting the TPS according to the manual and it idled at 2200 showing 4% throttle at idle on datalogger. I also tried screwing in the BISS srew all the way and that just brought...

What specific steps would i need to take in order to install a 1g CAS with black cover on my 98 gst? I am installing a 93 gsx head on my 98 gst. I was looking at a CAS from a 94 eclipse and it appears that i would connect right up to the 2g connection. I was planning on using my 97-99 CAS but i...

My car started making a tapping noise that appears to be coming from the exhaust side of the head when i start the car up in the morning the other day and when driving under boost, anyone know what might have caused this? I think it might be a clogged or bad lifter, but i'm not really sure.

My friend has a bad connection from his alternator to his battery on a 96 GST, can he just run a new wire from the alternator to the battery?

I have a ported and polished 1g head that i want to put on my 2g, i am looking for a list of parts that i will need to do the swap, and also want to know what parts from the 2g will be reused. Specific to installation on a 97-99 eclipse GST.P.S. I have looked at the RRE tech tips and VFAQ...

I have been searching around for other vendors that sell piping for GM MAFT blow thru setup and havnt found anyhting, i know Dejon Tool makes these but their prices are outrageous ($200) so i was looking for an alternative. If anyone can direct me to a vendor or a thread with pictures that shows...

I was wondering if anyone has the Mitsu part numbers for the bolts that hold the pressure plate to the flywheel and also the bolts that hold the flywheel to the crank for a 2g eclipse GST.Thanks.

I'm finally getting my car back up and running after 4 months of sitting and not being started, and i just wanted to know if there is anything i should do before starting it up again so that nothing happens to any components. The water in the radiator is really rusty, can i used a flush to clean...

How can i install a 1g head on my 2g eclipse GST? I just bought a 1g intake manifold and found out its not a good idea to put it on a 2g head, so now i want to find out what is involved in installing a 1g head on my 2g? Your feedback is greatly appreciated.

I need help figuring out where to tap the tach cable from the MAFT translator, i read the VFAQ but the instruction there say to tap it from the computer, where else can i tap that cable from? This is going on a 98 eclipse GST. Is there any 2g owners out there with this set up that can help me?

I did the 1g bov mod as shown in the VFAQ to hold more boost and now my car wont boost past 14lbs, i have the boost controller set to 16lbs. The bov that i used came off of a 90 laser RS turbo. It looks a little different from the bov off of an eclipse in the sence that the vacuum line...

I want to replace the the leaky cylinder head on my 98 GST, but i dont know whether to use a 1g or 2g head. I have read that the 1g head flows better than the 2g but it seems to require a lot more work to replace than just replacing it with a 2g, and i cant afford any downtime with my car...

If anyone can please direct me to some instructions on replacing a water pump on a 2g eclipse i would really appreciated it. The water pump on my car seized :cry: and i need to replace it ASAP.

I was wondering if an A/C Compressor from 2g NT will fit a 2g GST?

I just replaced a completely worn ACT 2100 lbs clutch and cracked stock flywheel with another ACT 2100 lbs clutch and Fidanza flywheel and now the clutch wont disengage at all. I bought a longer slave cylinder rod but it didnt seem to have done anything except not allow the clutch to fully...

I just replaced a completely worn ACT 2100 lbs clutch and cracked stock flywheel with another ACT 2100 lbs clutch and Fidanza flywheel and now the clutch wont disengage at all. I bought a longer slave cylinder rod but it didnt seem to have done anything except not allow the clutch to fully...

I just bought a greddy FMIC kit for my 98 eclipse gst and noticed that the pipes are designed for the stock turbo, not an aftermarket, such as the 16g i have on my car. What can i do to make it fit?

Every time i go to the track i seem to screw up on the take off due to the stickyness of the track, my car stalls everytime i try to launch and reduces my time significantly. If any of you experienced drivers could give me some tips, i would greatly appreciate it.

I was just wondering if a 3000GT VR4 fuel pump can be used on a 2g eclipse, need to know so i can make a decision on purchaing one today at a good price. If so, what changes will be required to adapt it?

Yesterday, i turned on my left turn signal to turn and now it wont stop blinking. I tried changing all of the bulbs and checked the fuses and they are all fine. This is really starting to get annoying and i need to fix it right away, any suggestions as to what might be causing this would be...

Are there any gains by removing the exhaust after the o2 sensor housing? Will it cause any problems to anything near the housing? My friend told me to remove the exhaust for better times. Any suggestions?

Can someone please tell me where i can find the cheapest j pipe to install my 16g on my 98 eclipse gst? If i get a 1g j pipe, how is it suppose to be installed (pics please)? Someone in town from a performance shop told me not to get a 1g j pipe because it wont fit, it goes into the radiator...

Whats the max fuel pressure supplied by stock fuel pump on a 2g eclipse?

Will it make any difference if i install a bigger -6 ss oil supply line to a 16g turbo than a -4? The -6 is a little bit bigger, wouldnt it flow more oil to the turbo?

Ok, i just need to know what the size on the fitting that screws into the oil filter housing for the turbo oil feed line, i am building a custom ss oil feed line and just need that fitting.

I have a big 16g i am getting ready to install on 98 eclipse GST and my friend is telling me that if i use 510cc injectors and a walbro 255lph i wont need to use an AFC, is this setup possible without an AFC? Or is it better to get the 190lph with the 510cc injectors? I'm planning on running...

I just bought a 16g turbo from a friend but i cant seem to be able to tell if it is a small 16g or a big 16g, how can i tell them apart?

I just baught a 16g turbo to install on my 98 eclipse GST and i need help installing it without an install kit from someone that has done it before. According to what i have read and understand from VFAQ, i only need a new oil supply line, right???? I can drill new holes on the oil return and...

Yesterday while i was driving home, there was a 3g eclipse next to me on the street and i kept reving my 98 eclipse GST and letting go to make the swoosh sound with the bov, i did this about 3 or 4 times and then all of a sudden when i tried to accelerate the car keeped stalling as if the fuel...

The CEL keeps coming on in my 98 eclipse GST with error code "P0170""Fuel Trim Malfunction (Bank1)", It happened after installing the stock cat (for smog) and a new downstream O2 sensor, anybody have any idea of what could be causing this?

I have a 98 eclipse GST, which i just rebuilt the engine on and removed both balance shafts. I want to know if there is a bearing on the rear balance shaft (runs off of the oil pump) that needs to be replaced with a block off bearing? I have read and re-read the vfaq on balance shaft removal and...

I need help finding out what would cause low oil pressure. I just had the engine on my 98 eclipse GST rebuilt, i removed both balance shafts according to the VFAQ and now i have really low oil pressure. The VFAQ states to turn the front balance shaft bearing so that the oil holes doesnt line up...

My mechanic bronke the nipple on the wastegate actuator on my stock t25 turbo on my 98 eclipse GST, he told me he couldnt find one so i told him i would look for one for him. Please let me know where to find one at a good price. Thanks.

I wanna change the transmission fluid in my 98 eclipse GST but i really dont know what kind of tranny fluid i should use.Any suggestions, please let me know. I race about once or twice a month.Thankx.

I am rebuilding the 2g engine off my 98 eclipse GST, i took all the parts to the machine shop to bore for forged pistons and rodes and to blance the assembly, i am thinking about removing the rear balance shaft and replacing it with a stub but i am afraid that it will affect the balance of the...

I am rebuilding the bottom end of my 98 Eclipse GST with forged pistons and rods, should the balance shafts be removed before it is put back together? What are the benefits of removing the balance shaft?

I have a 98 :dsm: eclipse GST with a 1g Blow off Valve that i would like to crush for more boost. Any suggestions on where i might find these instruction please let me know.