I have a 97 GSX. My question is I need a new water coolant bypass pipe that runs under the exhaust manifold. I have a part number for the pipe: MD319841. I was wondering if this part is the same regardless of having a 6 or 7bolt block. The guy I bought this from said it has the 6 bolt, but I've...

What's up everyone! I have a question about swapping my automatic transmission for a 5spd tranny. I've searched the forums, but didn't really get all of the info I was looking for, and a lot of the threads delt with a GST..etc. Anyways, I'm thinking about doing a swap and I have some overall...

I'm building up a 2.3/2.4l stroker engine and after the install of the crank and bearings there was a problem when the arp studs where put on. You couldn't turn the crank really. Has anyone had this problem? I was confused of why these studs would cause this. Now my block is at the machine shop...

What's up everyone? I'm in the midst of building my ride up. I'm going to run a 38mm Tial wastegate with and open dump tube. I've been trying to find sound clips, but I haven't been too lucky. I was hoping someone here might have one and especially on a dsm, so I can know what it's going to be...

I just wanted some helpful info from you guys. I've been running a mitsu style turbo (14b and s16g) since I've owned my car. I'm now upgrading and going with a 57 trim t3/t4 hybrid turbo. I'm trying to get my manifold and O2 set-up correct. I have a guy I might be buying a manifold flanged for a...

I just installed a 255 and the import evolutions afpr kit with guauge 6an lines and all. When I turn the key, my gauge is at zero then when I try to kick it over it takes a few seconds and then finally after somtimes hitting the peddle a little it'll kick over and start. Then the fuel gauge...

What's up? I'm looking for a dyno shop around Indiana. Doesn't matter if it's in Ohio or Chi-Town either, if they are close to the border. I went to a place here in Indianapolis and wasn't happy at all with the service or quality of work. They really didn't do too much in increasing the power...

I just installed my S-AFC and used the instructions I found on the forums to figure out the wiring and all. I tuned it, then turned my car off and all the stuff was gone and reset. Any help? I used the red wire for power the orange and pink for air flow and the grey was ground if I remember...

So I put on a small 16 g and curved the wastegate so that the intake didn't hit it. When I got it on though, it kept hitting the uicp. So we kind of turned it so that the filter comes to the side of it and the whole setup isn't stright. It looks weird and didn't know if anyone else ran into this...

After reading a few posts I noticed a lot of people saying not to get a FCD. I have the HKS FCD, actually just bought it. Here's my mods I just got and I'm putting on:Installed: small 16g ported and clipped Extremepsi UICP 1g bov Weisco forged pistons ported 2g manifoldGetting...

Just installed a small 16g turbo. I also have a Greddy intake with 2g mas and filter. When I was trying to put the intake on the wastegate pipe was hitting the bottom of my intake and there was no way I could put the hose on the wastegate. I know a lot of people on here have upgraded turbos and...

Does anyone know a link where Ican find the diagram that shows how to splice the 2g mas into the 1g wiring?thanks

I'm about to do a major upgrade to my ride. I'm about to get/have a ported and clipped big 16g, 550 injectors, 190lph fuel pump, afc, Dejon Tool 2.5" blowthrough GM maf system with translator and piping, almost chrome color, fp 4" intake with 2gmas and apexi filter/adapter, ported 2g manifold...

Thinking about getting this 2g eclipse 95 turbo fwd that has the 7-bolt. I've heard about the crankwalk for this year. Is there anything you can help me on of what to look for and so forth...I don't feel like getting a car and then bang done for. I know it has about 130k. Should I pass? It...

I have a FP 4" intake that when I took my stock intake off I noticed the coupler is way bigger than my turbo. Is this made for an upgrade turbo, or can you get a coupler to ft???Thanks

Okay, another thing i'm wondering about is my new intake I bought. I have the Greddy Type rs bov which vent out. So right now on my stock intake i have the bov return tube capped. Now when i put this new intake on that ill eliminate the bov return and I won't have to worry about it anymore...

okay here's the deal, i was getting some repairs done to my car and I had just bought this upper intercooler pipe off ebay that came with a Greddy type RS bov, and a new throttle body. I had the mechanic shop install it. They said it took them 2 hours to get on and that they were having a lot of...

All right, I'm looking to get a new BOV and uicp. I once had a TurboXS RFL, but it was too much and I didn't like how it didn't recirculate. I'm looking at a Greddy Type S, and I know this is common. It's off ebay. Is this a good choice with nice sound and reliability?Also, I once I think...

What's going on? Well, I just got a credit card and was curious how many people use these to get there parts? Also, i was wondering if you did have one, did you get small things or big like a fmic kit...and so on. I'm about to get some things for my ride and didn't know how good of an idea...

This is happening more and more often, but when i push down on the gas my car starts to sputter or bog. Sounds like the car is shitting or something. There's no go and it feels l9ike if I pushed on it my engine would blow. Some times if I catch first gear wrong it does this in 1st, 2nd, and then...

I live in Indianapolis and wanted to see if anyone's down for a meet? I'm on break right now from college and I'm sure a lot of you are too.So let's get something started and maybe do the traditional Hooter's meet??? Give ideas for day and time!Chris :dsm:

okay I started my car today, put it in reverse and when i was letting up on the clutch i heard a sound that sounded like air leaking out or something?? So what the hell is that??? Then i put the clutch back down it went away, i started to let back up and there it was. Same when i was letting...

Not sure if this is a dumb thread, but I love the way nitrous can scare boys with the purge valve. I have a buddy with a WS6 and it has a 150 shot. I got the idea form a honda page I was looking at and I know DSM's can show them up. So if you have pics let's see what u have and how many have...

Sometimes when I punch it and the turbo is boostin hard I hear a sound that sounds like a loud scream from the engine...Is my turbo going bye bye???? :dsm: I have a vacuum leak right now too if that helps...Hope you guys can lead me the right way..thanks for your time

My spark plug wire is popping out. I thought it could have been the wires or the valve cover. When the car is on it will slowly move up then pop out. Of course this makes my car run like sh*t and I want it to stop. Everytime i drive my car i push it back in and while i drive maybe 5 minutes or...

My problem is pretty simple, but I have no clue why it's doing it and if there's anything that can be done to fix it. My spark plug wire that's closest to the timing belt cover is popping up. It normally does it when I smash on it, but when I first had the car I never experienced this problem...

I have a vacuum leak coming out of the ....well hard to describe but here I go...On the throttle body there's this cylindrical piece that points up. My car was dying and shit and I could hear this awful leak. I put my finger over that piece I described and the leak stopped and my car would...

Okay i've picked up that the FWD cars have a stock open differential. I just blew my tranny and wanted to know if i need a LSD. I saw on BMTranny that they have a custom LSD that converts the stock to a LSD. Is it worth the $$ and is it a reliable product?Chris

Do 1G's have a limited slip differential stock???Chris

i have a 90 turbo fwd...I';m looking for a new tranny and wanted to know if getting a non turbo tranny is bad..i have a Stage 2 racing clutch too..Chris

Real quick...I cut the canister on the air filter and now my air filter bangs up on this metal piece and it's eating through the filter and denting it...Any quick tips?? I have an old tire tube cut out and standing between the two, but didn't kow if there are any better ideas..Thanks:dsm: