TPS & base timing are set propely but just stopped and there is no control on it.TPS < 1%
Base Timing 0 degreesIdle % vs Target table does not work. I mean, if I do any kind of change in the idle tap, nothing happens. That's my problem. It has the calibration setup but I can't adjust it...
SorryThat's my tune, file above drive linkThe car is running but idle problems, bad idle cold starts, no A/C adjustment, I did the screw adjustment warm engine to get stable idle at 1050 rpm.I already tried AEMpro 450cc calibration file and idle just never change. the IAC Valve is good, I...
ok, this is my street tune. I just escale the map to use 550cc evo injectors. However idle valve does not respond to the software. Idle % vs Target Table does nothing. Also pin 7 that is supposed to work with switch 3 for A/C compesation does nothing. The oem A/C request works positive signal...
Does anyone know what's the AEM v1 PNP 1g board circuit?I'm having some problems with the idle. When I try to change something it does nothing. I already replaced the IAC also check vacuum leaks. All good. The problem is something in the the board I thinkThanks
Hi guys I see some people running bkr7 spark plugs. But the ceramic of the spark plug is a little smaller than BPR spark plug models. Can I still use bkr spark plug with the stock spark plug wires? Is that a problem?
Hi guys,I've been reading about flex fuel,I just want to know more information, if someone has done this system swap, if there is a guide of something.Thanks
Hi Mello. Sorry for delay on replying to you.
I've been testing many things and finally I found what was wrong.The AEM V1 PnP sees that the A/C is always ON but it's not ON, so it always compensate, that's my problem.So I decided to check my A/C options. The thing is that the OEM A/C...
Hi guys,I've been struggling with my AEM EMS v1 on my 1G 4g63 trying to configure the idle correctly, however I could.If someone knows how to do it properly or have a file so I can do itThanks
hi guysI finally installed my AEM EMS v1, but I can't connect to the ECUI tried 2 cables Serial to USB
CH340 driver and prolific USB serial driver but didn't workI am running windows 10 laptop trying to connect AEM pro.i really need helpthanks
Hi guysI would like to delete the internal wastegate of my 14b turbo. I have a 2g exhaust manifold.I've been researching and I see 2 options.1- Weld on the longest tube of the exhaust manifoldI don't like this one because I know it has to be where the 4 tubes are toguether2- Weld it...
I been researching about this o-ringit says MD030764 part number 33.4mm diameter, however what's the thickness? I need to know all the specs of this o-ring, if someone can let me know please.
I don't know where to plug the signal output from the map sensor, I see 2 pins 12 and 16, where should it go?I mean i'll run it speed density but pin 12 says ignition timing adjusment, and the other one Plug and Play barometric pressure sensor, i am confused
Hi guys I'm about to install my AEM V1 plug and play on my 4g63t 1g.I'm currently running stock ECU + maftI'm wondering where do I plug the signal from the map sensor?. I'm confusedIt's a 3.5 bar AEM map sensor 3 cables.Also if you have any advice for the installation and the first...
@Darren Thomas Racing 4g63t 1g, it's a galant swap to 4g63t f5m31 fwd. I'm currently running non eprom ecu + maft 450cc 14b turbo, basically stock but I want Speed Density IAT
@Darren Thomas Racing hey bro I am about to run AEM EMS V1. do you have some file you can spare me? I am new im excited about tuner pro. but I have to many questions things to learn
Hi guys, I need an start up calibration for a 4g63 1G stock for AEM EMS V1My car is a galant swapped to 4g63t 1G it has the stock ecu 1g galant vr4, however I am about to use AEM EMS V1 plug and play, but I dont have an start up file help me pls