So basically I’m confused as to what this issue could be, anytime I hit about 65-70ish under somewhat heavy throttle, it feels as my right side of the car is almost skipping or shuddering I guess would be the best way to describe it. I don’t really feel it inside the car but more so coming from...
Just curious what you all are using for your cv axel replacements, I just recently got a new driver side axel from o’reillys and just putting miles on that to see how it’ll hold but they don’t carry the passenger side so I’ve been looking elsewhere, looked on advanced and autozone and I don’t...
Alright so I just got my car back from engine builder and dyno last week and everytime I start my car and it’s in low rpms I can hear this clacking noise, I’m not 100% sure if I’m just tripping out and this is normal or what but I just wanna know what you all think. I’ll add the video.
So I’ve been trying to get to the bottom of this issue and would like some opinions on it as well.So I took my car home from our shop about a month and a half ago and on the way home it got a bad misfire sounding like it was only firing on two cylinders, I thought it’s the crappy iridium...
So I just recently got ECMLink installed in my car and got it running as it should. On my log it is showing my AFR to be lean at idle, also I have an AEM wideband gauge and I spliced it into pin 76 for the front 02 sensor and when I select the front 02 sensor as my input pin for my narrowband...
This car man… these things make me lose hope. Anyways, so I’ve been fighting my idle and I went to test it out today and started driving and made it about 30 feet when all of a sudden I heard what sounded like my cam gear cover rubbing against the cams, then my car died, the engine is fine and...
Alright so after finally getting clutch in my car I took it for a drive, started great and was idling at 850, let it warm up then started driving, once the car got hot and I’d try to come to a stop then the car just dies, I can start it right back up and if I’m holding the gas then it’ll stay on...
So I replaced my fuel filter when the engine was out of the car and since I got the car running, the bottom line on the ff is leaking. I’ve tried looking for the crushwashers for the filter but I literally cannot find them anywhere. Where did you all find them?
Alright so my car has never had fans on it since I’ve gotten it and wanted to change that, so I got some mishimoto fans for the 2g and they have plugs on them but I’m thinking I might have to hard wire the driver side bc it seems the connector was cut from the harness, I’m just unsure since...
Alright so I’ve been fighting with this clutch since I put the car back together and I just can’t figure out what’s going on. I have a brand new clutch, pressure plate, flywheel and tob in the car, the master and slave cylinder were recently replaced, the pushrod in the new master cylinder was...
Alright I know there are a million threads on this but I can’t seem to find any full answers just partial on it. Since I got the car the oil pressure gauge has not worked and I’ve had that on my mind, the car just had too many other issues but now I’m on it. I have a brand new OEM sending unit...
Alright so I just started my car for the first time last night since the rebuild and everything went perfect and it sounds good and healthy. I had to bleed the clutch today so I pushed the car into the bay and just wanted to start it up to hear it run again and so that’s what I did, started the...
Alright so I put the motor back in the car and I’m hooking up the lines off of the filter housing and I cannot figure out how the line runs(the one that has the hard lines), I’ll post a pic, what I’m basically asking is does it go under a mount or how does the line actually route? I should have...
So I blew my car up about a month ago and have since then pulled the motor out of the car and have it fully pulled apart and ready for the machine shop, I’m planning on getting a new crank, rods and piston heads along with cams and a valve spring kit and intake and exhaust valves, so pretty much...
Alright so I wanted to start a new thread about the idling in my car. When I start the car it idles at about 1800 then shoots up to ab 2000 rpm’s once it’s warmed up, I checked my tps it’s getting 4.62 and 5.07 volts when it comes to pins 1,4 and then 3,4, when I got on my scanner app with the...
So I’ve done a lot of work on my car and it’s almost starting, I got it to turn over one time and now it’s just crank, I know it’s my timing because I lined up the gears and they didn’t line up right, it wasn’t off by a lot but I know the slightest miss in the timing won’t allow it to fire, so...
I’m trying to get my car to start atm and I recently got the car and the previous owner that worked on the car completely messed up the harness so I’m currently going through trying to fix everything I see and I’m pretty sure the wiring from my starter relay is the problem for my no start and...