Using p/n 30-4110. I’ve read there are better widebands for this but this is what’s on the car0-1v can be sent to the ecu but default setting is 0-5v. Does ecmlink allow the 0-5v when you enable narrowband simulation? Or does it still need 0-1v regardless?Is 15 seconds enough of a startup...

Not sure if I'm having this issue because my wbo2 settings are incorrect (what shows in link vs what the gauge reads are not exactly the same (link shows richer)) or if my nbo2 settings are incorrect (switch point I went off the instructions but not sure about delay for the front o2). I also...

If you have a spare oil dipstick, this is the mod for you. Buddy gave this 2g one to me for free but I have a 6 bolt so I couldn’t use it. I had the idea to simply cut off the end and then took off any sharp edges with a dremel and a flap wheel.I park my car outside and dirt, leaves, debris...

I spoke to someone at Mitsubishi they sent me a link to put in a request. She said this is the correct link to use as it will go to actual agents:https://www.mitsubishicars.com/contact-usWhen you go to that site, scroll down and you’ll see a drop down menu. Radio code trouble is the option...

I had an aftermarket Pioneer single din and installed a 3000gt radio. I believe I only have that big white plug that goes into the radio and it’s all that I used with the Pioneer.I now have no sound from my speakers. Am I missing something?Edit: Speakers aren’t stock and the stock amp isn’t...

I had an old AEM UEGO wired to front O2 for narrowband simulation. I noticed in my logs that it wouldn't move from .8vI decided to put the stock front O2 in (brand new Denso), connected the stock wire back to the ECU but by accident left AEM wideband gauge assigned to the pin even though in...

FWD trans if it makes a difference. Busted the clutch line about two weeks ago. Replaced the clutch line, bled it as best I could and was able to move the car around the driveway.Decided to adjust the clutch pedal by the cruise control switch (pedal was sitting high the switch was backed all...

I assume not but want to double check before I go to tighten everything up and bleed this thing.I messed up the stainless line and saw it bolted to this fitting that was then bolted to the slave. I connected the new stainless line directly to the slave instead.

While replacing the front motor mount I found this spring sitting on top of the trans where the shifter cables are hooked up. Anyone recognize where it’s from?Fwd manual trans if that will help

I’ve been having a bit of an issue with the car running and noticed my timing is slightly off. I took everything apart to redo it but noticed the side motor mount bracket won’t allow me to insert the long tool to compress the auto tensioner. I ended up loosening the tensioner pulley which...

So maybe I’m doing something wrong here but this is driving me crazyI have a 1G N/T TB on my 6 bolt swapped 2G using the 2G TPS. I usually adjust the TPS after unbolting the TB and loosening the throttle cable. It’ll be at .63 then after I start the car and turn it off and check again it’ll be...

I’m having a similar issue. Tried a different coilpack and PTU. Went to cut/extend PTU harness so that I could bolt it to the intake manifold and white wire just fell out of the connector. De-pinned it and soldered a new wire onto the pin. Put it back together, cut/extended and bolted to the IM...

When I bought the car both slim fans were connected to a toggle switch along with the wideband, boost and voltmeter gauges on the a-pillar. I cleaned all that wiring up and now have the gauges come on with the ignition. I was going to wire the fans to a cleaner push button style toggle but then...

This is the second time I’ve seen someone with one of these. I love the look of it especially on this Talon but owner isn’t sure what it is.

I still have to call the few shops near me but I’m looking to have my mains align honed after having ARP studs and Kiggly girdle installed in a spare 6 bolt block I have that’s disassembled.Located on the border or NY and NJ. Willing to travel. I just want the job done right.

I found a 6 bolt short block about an hour away that has pistons, rods, stock crank and no balance shafts. Lower pan, front case, water pump and timing components are on there also. I’m going to check it out this weekend but..1. I don’t have a pick up truck so considering removing the pass...

Ordered this lock set from Miller Imports since my key only worked in the ignition.Went to swap the ignition lock today and noticed the new one is a little shorter than the old one (new left old right). Looks like the cylinder at the end is in a different orientation as well.Is there a...

So.. since putting my car back together I noticed I’ve got a knock at idle. I intend to pull the oil pan but I imagine a bearing has spun. I plan to take the head off to be tanked (already have new lifters on the way) and I’m probably going to get another short block just to play it safe...

If I’m reading this diagram correct, looks like previous owner tapped into the lock switch and ground? Why would this be done?Under the kick panel I can see the added ground wire (brown) is broken and the added power wire (red) is connected to some blue wire but I can’t see where it goes.

For whatever reason the TPS was flipped the other way (picture shown) and reading 1.3 or 1.4V car off. I got it flipped around but can’t get it lower than .80V and am using ecmlink V3 to check voltage.Is there anything I can adjust on the TB to get closer to .63V?

This is the only decent picture I have of my intake manifold. I don’t see a bracket for the PTU or a spot to even mount one.Can I extend the wires and mount it on the firewall?

This is the Build Thread for 95 Talon TSi. Reply below.

In a little situation here.. This is my first DSM. When I bought it the passenger side handle was completely missing. I bought a pair of handles to replace both but haven’t had a chance.I’ve never had an issue with the driver side but I closed the door today and it won’t open back up. The...

Can’t find the post now 🤦🏽‍♂️Wasn’t aware they made bodies of these cars

I want a “beefy” look on the car. Found some AD08Rs locally for cheap but they’re 255/40. Based off research that size is pushing it especially as these probably run wider than a standard street tire. Anyone have personal experience with this combo?Wheels are Vors SP1s with 245/40s that need...

First thread! Going to be completely honest, I don’t know shit about these cars ;) I’ve had several 4th Maximas for over the past decade (currently have one with a semi built cammed 3.5 and another that was turbo currently working on a new kit and a fully built 3.5). Those cars are my bread and...