acdraindrps - did you ever get to fix the P1495 code? I'm facing the same issue right now. I've already replaced the Leak detection pump and didn't have any luck. It is time to drop the gas tank thinking i may have the same part that needs to be replaced.was hoping to get some feedback from...
Thank you VelocitaPaola!I will look it up and see if I can find a picture. In another thread it was described being a part that had three hoses going to it that can dry up over time and cause a leak. I'll see what i find! Again thanks!next step is to get the tank down and see what is going...
I've read in other threads that the gas tank has a vent valve that is located the top of the gas tank.Does anyone know the model number for this part? 98 Eclipse GS.
Still struggling with this code...I've gathered some information, on the behavior of the car. Can someone validate the information provided?I traced the sensor wire from the LDP and found it under the back seat near where the gas pump is.I checked on each of the pins the voltage and...
An update for everyone.I finally got a chance to look at the car. I didn't drop the tank b/c everything is pretty rusted below the car and i didn't want to break anything else.I did take out the vapor canister purge solinoid and make sure it was ok. Visually inspected it and cleaned it with...
Thanks for this! I'll check it out.Can someone confirm though if the LDP is near the gas tank on this car? Seems I need to get under the car to soap it up a bit also to see for any bubbles that may be occurring.
Hi everyone.I understand that there are other threads for the P1494/5 codes, but none really have a solution posted.I have a 1998 Eclipse GS and I have the code P1495 that is appearing now. I was having 1494 and 1495, I cleared the codes and now only P1495 is present. It comes up almost...
800 bucks later.... I just did the timingbelt and water pump since it was right there. Magnet is now out :)I'll have to take a picture of it and post it.
I got a borescope, it's diameter was 17mm and didn't fit in the sparkplug hole.
No store around me had a thinner camera.I did try those grabbing things. But since i dont know where the magnet is in the chamber, its hard to find anything to grab on to.I did cut one of those up through to...
We'll I'm about 99.99999999% sure its in there. It had grabed the socket that was in there and when pulling it out, only the tool came out. No socket or magnet.I ended up getting the socket out but the magnet is in there.Last try. I got a 16lb magnet which won't fit in the sparkplug...
Yup, just a 420A. If anything I can do the timing belt and water pump as those will be right there.We see unless the tech finds another way to take it out.
My girlfriends dad was trying to help and dropped it in.I did not see a magnet in the socket, check also for it.Unless I can get a camera in for sure to see, I can't know and will haf to take the head out.
I did not find another area that was a better fit for this thread , if one exists please move it.Regarding the fire I don't have any torch like that. Camera did not work. Was not thin enough.Maybe a shop has a better camera.Gonna try to make an electric magnet.
It was 5/16 socket. Went to tighten the valve cover bolt and it fell off my socket wrench right through.Got a camera but don't think it will work it's 17 mm diameter.
I had a socket fall threw sparkplug hole into the cylinder.While taking out the socket the magnet on the end of the telescopic tool fell off.I later got the socket out. But don't see the magnet or feel it as I stock a coat hanger it to feel around. Any idea how to get it out? Will...
almost sounds like your sound.For mine i drove it again and its for sure from right site, like a crack crack sound, i turned off car and let it roll a bit and it still made it, the road was flat so its not suspension.Any chance this may be something with my tran?Will try to check...
Hi,in the last few days, my car has decided to make some noise from the right front.The noise sounds almost like a wheel bearing but the sound only starts once the car is rolling. If i accellerate or hit the brakes the sound goes away. The sound starts to happen when the car warms up a...
Finally did some scanning in my car since i didnt drive it for a bit.Some of the stuff i pulled with my scanner from the freeze-frame the code was tossed at:Engine RPM: 832
Load Value : 4.7%
MAP Sensor: 43KPA
Coolant temp: 163 degrees Fahr
Long Term Fuel Trim 1 : 24.2 %
Short Term...
My scan tool won't show me live readings. Its an Actron cp9175 i think is the model number. I can see what the fuel trim is through at the time that the code was thrown because it creates a freeze frame.
Per the sensors it shows that the o2 sensors are both ok. I'm thinking its prob a vaccum...
bump to the post.I'm still seeing the code come and go. I've checked my o2 sensors with my scanner and it says that those are all ok.I do get a freeze frame in the cpu and I'm not exactly sure how to read it. but one of the fuel trim values doesn't look right.Any tips?
Looking for ideas guys.I have this code on my car appear for a few days now. I clear it and it comes back after couple days. I have not noticed any performance impacts or any issues with the car driving. I have a 2GNT 98.Any ideas? thanks.
Ok, I suppose for now the problem seems to be resolved.It turns out that the issue was not my alternator fuse.
The alternator is also working well, once I got the car started, I pulled the negative line from the battery and the car ran just fine.What did I do to resolve the issue?
1...
I wasn't able to find any pics of where the alternator fuse is on the 2G N/T.I did check the fuse box in the engine bay and i did not see any fuse blown.
The positive wire does not get hot.Some other things i noticed.Now when I went back i turned key to on, the lights on dash were dim and slowly got stronger, but when i would go to crank, the lights would die again. with no key in the car, when i hit my hazards, nothing happened.seems...
Hey guys,yesterday my car died and i jumped it just fine. Got home (drove it for 20 miles) with out any problems, turned car off and went to start it, again the car had no power. Went to jump it again, the wires were all correct red on + and the black on the negative pole.After a few...
Ok, well I took it out to a shop as I had said, I'd like to believe that they bled it correctly. I'll look under the dash again today. I looked this morning and noticed that when I hit the clutch it has pressure in it but it hits the firewall. So I think your write that it needs to be adjusted...
Hey guys,Question, 10 days ago we had a very very cold night. I parked car and was running fine shifting all ok. Next day as the day went by the shifting got harder and harder, eventually i couldnt shift unless I turned car off. Took it to mechanic and said i had a leak in my master and...
I have looke all over this forum for this information but i can cant find it.I have a 98 2gnt and need to verify that those only have 1 type of tensioner. a 7-bolt.thanks
Hey guys, i was going to order some bolts for my header, i might not get the dealer ones b/c a buddy of mine said they can get some that won't loosen after i put on the new header but i need to know the size for the bolts that i need. do you guys know off hand what size they are?sdsdsd...
well i got the stuff now cant really get rid of it. i have the greddy header and the evo exhaust is the one that is 60mm all way through and tip is 70mm if i remember correctly is that the one ur talking about?
yeah i got someone getting me a gasket and some new bolts incase any break. Thanks for your help everyone just wanted to make sure i got everything and i am taking it to a shop my friend owns one hes gonna put it on for me.
well i have an aem CAI intake so far, and some ngk spark plugs didnt get the wires yet. i wanted to put the exhaust on first. im not sure what my hp is now, shouldnt be much should be around stock b/c the intake i dont think adds hp maybe a couple, even though i noticed a difference. but i want...
Hey guys whats up just got my greddy header and greddy evo exhaust for my 98gs. What else will i need to install the exhaust, im going to keep the same catalytic converter for now. if someone has done a similar mod please give me some pointers before i run off and change it.
sdsdsd
Hey guys, i want to change my interior lights on my 2g, i read the one about the blue lights but wasnt sure what i have to do. do i just take the lights out from the buttons and put the blue bulb on it? but then what do i do with the 330ohm resister? and howdo you get the hvac out i was having...
hey guys, whats up, i took part of my hvac area apart today to try to see if can find the lights but i couldnt take out the hvac itself out? how would i go about that? also i saw that some of the switchs have little lights in them i just unscrew those lights out and unsolder the old leds off and...