The 1g 7 bolt has been out of circulation for a while. The only picture I've found is on STM and it looks about as thick bodied as this new one with a bit more bending of the nozzle. https://stmtuned.com/products/mitsubishi-oem-oil-jet-squirter-for-1g-7-bolt-dsm?_pos=10&_sid=430d6021d&_ss=r
I recently pulled my oil pan on my 2g piston 1g rod motor to find a broken squirter nozzle at the bottom. Motor was assembled 20 years ago before there was much info on 2g pistons possibly hitting them. Fortunately it's only 1 of them but I suspect I've spent the past 2 decades driving with it...
I don't believe it, they still have the 90-92 gaskets in stock as well. Never would have expected that. I just ordered, we'll see if they actually arrive.*EDIT* Nevermind, just got an email stating it is discontinued and order is being refunded. I'll have to look and see if the 2G gasket...
The lower plastic timing belt cover has a rubber gasket that gets hard and brittle over time. Mine is missing random chunks. Has anyone found a decent replacement for this? I could go the route of just buying an whole new OEM cover but for now on this motor I'm hoping to just get a decent...
Would leaky valve stem seals have any adverse effects on tuning and wide band readings? I've had a hard time with a wide discrepancy between 02 reading at cruise vs on boost. I can tune cruise properly but then run lean under boost, or I can get the top end right but then cruise is rich. I...
I was referencing a thread from last month on the same subject here: https://www.dsmtuners.com/threads/resolved-help-wire-up-a-fuel-pressure-sensor.516386/I'd rather use the MAS 5v if it's all the same, I already have cut into that harness to wire my 2G MAS. I figure I can just splice of the...
I'm looking at old threads on this topic but still am uncertain about getting a good 5v source for the sensor. I have the cheapo made in china 0-100 psi ebay sensor. Car is running V3 with 2g MAS. At this time I think my only available input is the EGT which is logging my WB now. I plan to...
Yes the Supra pump is old. It was bought off an Supra owner so not new when I bought it. I'm sure it's over 20 years old now. Stock lines, Spooling up FPR (if you remember those). ND 720's that I had cleaned and flow tested but that was a while ago. Fuel pump is already rewired. I've been...
Thank you for posting this info. My setup is pump gas but I've been dealing with these same problems for a long time. My car runs great at cruise and around town, easy to tune, then once boost hits my WB Factor goes up to like 22%. Changing base fuel pressure didn't fix anything. I had my...
MB196420 is definitely not the clip you are looking for. I just ordered two thinking they are the plastic/nut clip you snapped a picture of but they are a completely different part. As far as I have found, I don't think that clip you are looking for was ever available to purchase separate from...
Ok so for the archives if anyone else runs into this:The best way to get these in is like this- the top of the bumper where it pops into the hood has a flared top that looks like it should push into the hole in the hood. Trying to push and twist will just shred the top and ruin the part...
I'd like any good ideas for replacing the 1G hood bumpers. I'm talking about the non adjustable round rubber bumpers attached to the hood. Either some aftermarket solution rigged up to work, or a good method for installing the factory parts.The replacements that Mitsubishi amazingly still...
Has anyone had any luck getting the 1g seat belts to bolt up to the Corbeau bracket? I have the lap belt on just fine but the retainer for the shoulder harness isn't even close to working. Right now my options are looking like letting that retainer just dangle from the belt and bang around or...
Definitely some great ideas here. I'd be all over OEM replacement trim pieces, interior panels, etc. Here are a couple that I didn't see mentioned, maybe I just missed them:1. A dual gauge pod for the 1G steering column like the one for the Evo:2. OEM quality headliner material...