Hey everyone,
Does anyone know what style of connectors are on the AC fuse box?
Some jerk put a AFPR where it’s supposed to be and I’d like to make a patch cable to relocate the fuse box when I go to add it back the summer.Thanks.
Hey Everyone,
I am trying to piece together everything to put AC back in my car its a 92 6 bolt AWD.
everything online point towards this as the compressor connector https://www.ohm-racing.com/product/ac-1-way-connector-evo-x-evo-8-9-1g-dsm
however the only thing around the back of the intake...
Does anyone know what connector type is used for the fan thermo switch on a 1G? i had a wire get brittle and busted the connector trying to remove the pin.
Hey Everyone,
looking for ideas.
right now i have the clutch position switch un plugged and the starter relay jumped i am getting an intermittent no crank
when i probe all pins at the relay during crank, I am seeing battery voltage at one of the vertical pins (3 i think) but none anywhere else...
Shot in the dark, but I got a car with a wideband with no markings it goes into a aem gauge which I hope means it’s an aem ( I’ve heard they’re crap though) would anyone by chance know what model this is?
sensor is from 2012 era I tried looking at some sensors on line didn’t see any with...
Hey everyone I was prepping my cylinder head last night and made the mistake of spraying the deck with Chlorinated brake clean. I have black nitride SS intake and inconel exhaust.
are these valves junk now? Is it worth to continue?
Hey everyone,
i ended up getting these results for a piston to valve measurements. and in not quite sure how i feel.
INT EXH
10 BTDC 215 250
7 BTDC 190 240
4 BTDC 170 240
TDC 153 250
3 ATDC 140 250
6 ATDC 134 250
10...
Hey Everyone, I am trying to degree my cams.
I have a set a kelfords and I have an indicator on top of the piston and one on the back of the valve. I am also using BLE solid lifters with the lash set as close to zero as possible.My issue is I am seeing about 20 thou run out on the base cam.
I...
Hey I got around to making my fuel line for pump to fuel filter. I can’t squeeze the -8AN fuel line following the stock line location in between the chassis and the subframe. what do most people do? It looks like hose can fit but not fitting. Do people just drop the sub frame? Is there a trick...
Hey everyone trying to run some -8 PTFE hose for my fuel feed line.
i am just wondering the best way to go about these fittings they are a real PITA.
i've tried various grinders, saw etc. but from what i can gather the heat from cutting causes the ends to swell and cannot install the first part...
Hey everyone,
I am trying to time my engine with English racing oil pump pulley and i can't get the cam and crank timing marks to align,if my theory is right shouldn't the crank be slightly above the timing mark due to the circumference difference?
if i move it one more tooth below it moves...
Hey everyone,
my engine has been apart a long time and the person who took the engine apart (may or may not be me) did a bad job on bagging and tagging.i am trying to see if i got the correct specs on the tensioner arm bolt, tensioner arm and idler pulley.the FSM is straight up terrible...
Hey Everyone,
when my car last ran i had blow by issues.
so this time around i opted to tap the block to create a breather port, as i'm running much wider ring gaps and more boost.
The casting is a little thin here at the tap so i am worried about fitting material selection, i know brass is...
Hey Everyone,
i got a set or Eagle H-Beams that i am trying to install however,
instruction say to use ARP moly lube to 43 ft-lbs for 5.5-5.9" bolt stretch.
i am using the lube supplied (arp ultra torque) smothering the threads and face as instruction say,
43ft lbs gets me ~4 thousands...
Hi Everyone,
i am noticing on my ACL rod bearings that 4 are stamped on the notched side and 4 are stamped on the other side.
i cant find any indication on either being a top or bottom, does it matter what way you install ACL rod bearings?
they came wrapped in the same sleeve.thanks,
-Will
Hey guys I just finished up weighing my pistons, wrist pins, and rings and found I have a 1.5 gram weight difference max to min.do you guys think it’s safe to take the 1.5 grams of the inside of the pin boss?I was going to put a gentle chamfer there.
Thanks,
-Will
Been Looking to find a replacement set of rear calipers for my 1g AWD, anyone know of a place that stocks them or a friendly swap for them? it seems like most people just look to buy a used set.thanks,
-Will
Hey Everyone.
i got a new set of wiseco pistons and eagle rods with rings cuts eveything good to go.
i weighed most of my components (minus wrist pin clips and rod bearings)
what do you think, would you run this?
i am kind of worried about the 1 gram difference between pistons.
thanks,
-Will
hey guys I bought a set of supertech nitrided intake and inconel exhaust valves with the bronze valve guides to match. I can’t find any recommendations of the guide clearance. Anyone here know?
Thanks.
Hey guys, recently got a line hone for kiggly girdle, was looking at assembly and now I notice I have some light scratches on my thrust bearing caps. Would you run this? It looks like a bore gauge gouge. I can feel it, it it very faint though, not much rougher thank the hone finish.
Thanks,
-Will
Hey guys, im dropping off my rods to set my wrist pin clearance. The Rods are Eagle CR5900MA3D and Pistons are Wiseco K559M855.
im looking at setting up the rod wrist pin clearance to .001" anyone have experience with this?
i have a kiggly girdle installed, with a PTPE 6262 with Kelford...
looking to find a front driver side wheel speed sensor for abs, but i cant seem to find one anywhere. does anyone have a resource for this?
thanks,
-Will
currently rebuilding a 6bolt (bare block right now) with a PTE 6262, wiseco HD pistons and eagle rods.
has anyone run this cam with no problems on stock lifters/followers? will obviously be grabbing a set of aftermarket springs.
thanks,
-Will