So I noticed some of the bolts won't torque down so I retap it but it looks like is not enough. I heard you can use heli coil but i do not know the dimensions. I do not know if I'm correct do I have to get kit that is m8 * 1.25inch or am I wrong. I own a gs not a gst yup I know why a gs well...

Alright well I don't know what I did or what happened but is not leaking anymore so I couldn't identify where it was coming from the core or the bushing. But is not leaking anymore

So I did my valve cover gasket and replace the bushing where the bolts but then later on I keep seeing oil coming through the bolts and lil bit from the gasket. I torque them to specs but some of them they won't torque because of the spacers it has I bought from eBay used ones cause I was...

Well I did the pressure test I kept in the 20psi and left it there for like an hour and just lost 1 psi. I'm going to try it again just to be sure and later turn on the car let it warm up and look at the same spot just to be sure that is leaking from there and not somewhere else.

So my radiator is leaking due to overheating cause of the stupid freeze plug. So this is the part that is leaking from idk what it is called And I was wondering is there a chance to fix it or am I f***ed. If there's a chance do I replace it or what do I use to cover it up

well i started of by rotating the front tires to the rear and put the rear tires on the front since it was wearing bad on the edges you could start seeing the wires (i was cheap i didn't want to buy new tires but only one of them was new). Then i did the alignment which i only move just the toe...

SOLVED!!!! i don't know how to switch it solved but yeah i figure it out

the noise still comes from the driver and passenger side. it sounds it comes from the wheels. those quick left and right turns you can hear the noise

i did ended up replacing the left side only but i was still able to hear it

So I keep hearing this whining noise coming from the driver side or passenger but it's probably from the driver side since I hear it more. Anyways the noise you can't hear it when I'm on low speed but as add more speed the whining starts and gets louder as I keep increasing. i do hear the noise...

Ignore about the car won't start my dumbass forgot to put the ground side of the starter. But anyways about the slave cylinder is the bleeding procedure different I heard from some people that sometimes most bleeding procedures are different. I was bleeding it the same way as bleeding the brakes.

Alright so this is what happened. I replaced my tranny with a new clutch and throw out bearing. I started to bleed the slave cylinder but my dumbass was too concentrated on the slave cylinder that I forgot to go back and check the fluid level and most of the time i was pumping air. So, I...

by any chance do you know where to buy the reverse thread bolt cause i checked on mcmaster and they only have it till 40mm long and bolt depot only have the nuts on reverse thread and i don't know where else i can find it.

Is it a left or right hand thread?

Thank you! I really appreciate it.

It's a 420a idk if the 4g63 are different

Not bad I keep forgetting about that. Umm is the one that is driven by the power steering, crankshaft and a/c compressor

The one Tightens the serpentine belt

So apparently the adjustment bolt from the idler pulley broke because the bolt was stuck and it wouldn't move. Anyways I've been trying to look for it online to buy one but can't find any. Does anyone know what we sit to get it from or at least know the dimensions?

Sorry this was stupid I just needed to cool off. I figured it out when I was calm

I'm having problems putting the bolts back on from the flywheel to the clutch. I replace my tranny and the clutch when I put the tranny back with the clutch inside I couldn't put bolts from the flywheel to the clutch. I put one bolt when I go to the next one is not align to the hole. Do I have...

Thanks but I kinda figured it out I just got lost where the pointy one go and the small one

I'm putting the transmission back but I forgot where the bolts goes on to the bellhousing to the engine block. The bolts are in different sizes so I don't want to put it in the wrong Place. This is the bolts that came out from the bellhousing and the engine block. I just need to know where the...

Alright hopefully I explain this right. My car has an EVAP code I forgot what code is it. I believe it's P0455 is the one with large leak detected. Now every time my drive my car to point A to point B there's this strong odor which I believe it's carbon monoxide because it gets me light headed...

What is the torque specs from the bell housing connecting to the engine block?

I'm replacing my transmission I already have a used one. I have already replace the axle seals and the throw out bearing. Now I'm trying to look for a clutch like good one not expensive just the best cheap or normal clutch out there. It's a 97 eclipse gs m/t 2.0L 420a non turbo

what type of grease should i use? is white lithium grease okay?

I bought a used tranny and im replacing the clutch and the throw out bearing. I was wondering do i need to lube the input shaft?

Yeah the bell housing and the outside

I bought a used transmission for my 420a since my older transmission got messed up. I was wondering is there any products i could use to clean the transmission?

sorry about that im like new to this and i've been trying to find the post i've made but i keep getting lost so i gave up and made a new one

I'm looking to get some valve cover bolts cause i apparently lost some of them and i was wondering what are the sizes for valve cover bolts on a 420a. Is there a website i could get them? or can i get them on a store? if so, which stores do i have to go to?

I really appreciate that I didn't know where to go either home depot or lowes. Well i would definitely go to ACE hardware

Ooh ok. Well i appreciate the help.

Are these good? https://raceboltuk.com/product/flanged-hex-head-bolt-m6-x-1-0mm-pitch-x-40mm-long/ idk if this stainless steel are good for valve cover

Apparently i am missing bolts from my valve cover. Is there anywhere where i can get them? or what can i do?

I'm in a need for used transmission where is a good website to buy them at. I have not find any on the junkyard this cars you don't see them a lot in Houston.

No not really it shifts fine with no noise but like i said it only does it when it's on cold start and random when its warm on idle. The only time it grinds when i put it on reverse sometimes it does grabs it and sometimes it doesn't it grab it it just grinds.

No but sometimes when I put it in reverse it grinds so I retake it out and put back in. The noise only does it when it's on idle sometimes when I'm in the streets it doesn't do it. It's weird sometimes it just comes random but I know it does it more when it's on cold start.

So this is the noise it makes when the metal particles are hitting or whatever it is. usually this only does it when it's on cold start but now it starts doing when the car is warm sometimes. Anyways i'm putting a used transmission i just wanted to know what that noise is.

I would make a video about the noise when the metal particles which I believe is the particles or something that is hitting

Well I picked up the car and I accelerated and there was no noise. I guess it only does it when it's on ground. I forgot to mention that my tranny has been messed up cause I been hearing a noise I believe it's the metal particles hitting but that's been doing that when I first got the car. the...

yea sorry about that i forgot about that well i made it public already

I made a video if it helps.

There's this noise that gets loud every time i accelerate more so i have to go slow to unable to hear it. it's only the front not the rear since i replace the rack and pinion, the axles which has abs i don't know if that matters, the rotors, and the brake pads. i replace the brake pads first...

Thank you! I haven't try to look for a video but I really appreciate it.

What are the steps to remove the whole rack and pinion gear? I already have the new rack the rack and pinion just waiting on the outer tire rods. Any tips?

Apparently I'm on a need of new axles but they only have them with ABS. Will it still fit on a Non-ABS?

The only reason i need a new header it's because it has cracks and is tearing apart, so i decided to buy a new one but cant decide which one is a good one.

Are they any good headers for a GS 420A. Are DC Sports good or PaceSetter? or are there any better than those?