So when my 2 12in l7 subs hit the volt gauge goes from 14 volts to 12 volts and that's only s 800 rms amp n the amp I wanna run is 1500 rms at 2 ohm stable amp requires 1 gauge wire with 150amp fuse.n my amp is 650 CCA with stock wire to chassis n alternator n audio shops say to run big 3...
My 420a 2g stock alternator is 90 amp. Will I b ok to get a 150amp high output alternator without frying wires or shorting things out my amp takes up 2 150 ampere kicker 1500.1
Will a A578 transmission kit cast is nv-t350 fit my eclipse 2.0 non turbo 5 speed 2nd Gen says it will fit 00+ pt cruiser neon sebring stratus let me no if it will fit my car thanks and my transmission says nv-t350 on it
The cams r in the way and I have had a base 420a model leak oil out the head gasket I'd replace the proper way. And the back battery side the head bolt actually is not deep enough that's a chrysler mess up so I drilled my hole deeper to fix chrysler mess up u should just replace it new head...
Yep I got some Mopar atf+4 and I have another transmission as a spare don't no if it if good I drained gear oil out of it no shavings and pop ed the bell housing off no chips in any gears from what I can see so I may try using it and I'm going to but a new input shaft bearing and output shaft...
To much work for me. What year dodge neon manual transmissions will fit 95 eclipse fwd non turbo. Cause someone I no had a neon transmission in his 96 eagle talon eSi. And will their be shavings in oil from shift fork
Yes the shifter base moves back n forth when I tap on accelerator n let off and what u mean by pop it and what retaining nut r u talking bout transmission only has 120,000 miles
Car shifted fine and today it pop out 5th gear 3 times other gears are fine and the srs light is on as well now let me no fwd non turbo manual transmission
Fwd 2 g eclipse got alignment done s pulls to left guy said camber is off and is not adjustable the alignment was supposed to be $60 he charged me $25 so here is the deal this is before alignment left front camber -0.3 caster 4.1 toe 0.96 right front camber -0.9 caster 5.5 toe 0.89 total front...
Nv-t350 manual transmission fwd where is the input shaft bearing located as well as output bearing is one on the bell housing but on the back side cause I see a roller bearing their
I have a nv-t350 manual transmission and I took bell housing off the gear case and where the input shaft goes into the bell housing their is a roller bearing what is it it conect to the shaft sleeve on bell housing
So if I take bell housing off the input shaft bearing is on the bell housing but to replace it I have to Crack open the transmission it's on a fwd nv-t350 manual transmission
The input shaft bearing is on the bell housing pop open the case and pop roller bearing out of bell housing n put new in not going to require a rebuild unless u toasted ur transmission LOL hour job if it's already out of car the output shaft bearing takes a while that's in the drivetrain
2.o non turbo 2nd generation manual transmission. Inside the bell housing where the input shaft is what is the roller bearing on the back side of the input shaft cause I opened it up and and it's on the bell housing let me no what it is and where is the input shaft bearing located,pilot bearing
Try to get under the car and look at the back side of head gasket mine leaked oil so I replaced it with MLS head gasket and take the timing belt inspection cover off to see the timing belt with that many miles it may need replacing/also check rack n pinion
I replaced 2 Gen fwd steering rack boots and my alignment is out of wacky I'm going out of state on weekend what's the best place to set the inner tie rod nut how many turns I have to much toe in I turned the nut 24 times which is to many my tires r squealing and outer tie rod was 13 turns
so i replaced my nozzles on my hood cuz their wasent any when i bought the car so i replaced the hood nozzles and hoses.my washer fluid will not spray idn why the washer light is not on in the car so thats a good thing i dont hear the pump kicking in but if that was bad i would assume that the...