Long story short got a cool billet thermo housing. It was however tapped for 1/8 bsp instead of 1 npt on both sides and I need an aluminum 3/8 barbIm coming up blank. Would like to keep it aluminum for consistency of metals best i canany help appreciated. Guy even said hed buy the fitting...
I am installing my billet housing when I drain my coolant. Id like to put in aluminum fittings but I dont know the hose sizes to orderer the right ones.I believe one is 5/8 but the other is smaller. Just need a confirmation
Here is the idea and I love it... the whole kit is over 1k but we only need dsm axle size! Someone with cnc capability could crank this out pretty easy.Its 2 "u" shaped wedges that bolt together with a place for a slide hammer to screw into.The slide hammer works if you can grip the axle. I...
This is a weird one. This sound only happens letting off the throttle. It almost sounds like a BOV in the video but its most definitely something metallic.I know the internet noise game is annoying but Im truly at a loss. Motor is brand new and didnt sound like this during heat cycling and...
New motor is in and drove it around for some break in. It is idling 10.2 through link and will go to 14 tob16 while mild driving.When i start climbing to boost it leans out to dangerous levels ao we just cruised.I tried evwrything in link to lean out my idle but it stays 10.2 no matter...
Put new motor in today and everything looks good except Im not getting power to overhead lights and radio... at least thats all so far.i stopped because my power to radio powers my oil gaugePulled fuses and all good. Im just not getting power to the cabin fuse box. Any of you electrical...
Heres a weird one... so I know timing is correct under the coverBut the fluidamper lines up with the corner not the "T"... the stock balancer is dead on "T"... is this normal?
Getting annoyed, has never given me this much trouble! Crank notch is either too advanced or too retarded, not sure what I'm doing wrong.Going to sleep on it but if you have ideas I'll post picsI might be there... 2nd opinion?
Not looking for a debate on right or wrong... I have my reasonsI know the pitch is m12x1.25 but I need the proper mm depth so as to not block anything that should be blocked.
Cirious if there are many of us that have just put in springs while on the car without checking measurements.Jafro showed perfectly why we need to do this but so many videos just show slapping new springs on a head.Whats your take amd experiences? Mine has to go to a shop either way
Im wanting to see pics of the manifold and exhaust set up on Morrisons stock replacementI notice the flange kicks up in the front which would change the o2 housing angle as well. Im trying to see how a downpipe would still bolt in with no modifications
I started taki g my head apart while motor is headed to the machine shop.I inspected my cam caps and they have scoring... my question is how much is normal?
1g awd auto always makes me feel stupid trying to get the passenger axle out.In the past ive had to put a clamp on it and hammer the crap out of it... this time i cant get it out no matter what.I need ideas please... also how can i prevent this in the future?Ive read using a chisel or...
I am having the worst luck with this car and at my wits end...Car has not moved at all and now while tryi g to pull the tcase the shaft is coming out of trans instead... never have I had this issue. Itd make sense if I was racing but car was just put back together... idled.. had rod knock...
Ok guys lets build a motor with me! Mines coming apart as youve probably seen. So lets build one together!This will be an occasional cruise around motor but built for 1/4 mile. Already has a built awd auto trans from IPT and ran e85 with 2150cc injectors. Tcase is braced and driveshaft is a...
With stock cranks seeming to be harder to find I came across a sweet deal on an unused eagle crank. $300 to my door.I have heard they need machining to work right... looking for experience so I know what Id be getti g into before I buy it
Short story.. after oil squirters falling out and getting some low pressure i fixed the issue... have great pressure but now there is low idle knocking.Im on the search for a new block and crank so I can have a spare short block.To my question..This is most likely a main bearing issue. I...
I know where to get full kits but I have to believe there is a source for just the lowers.Id like to keep a good amount on hand since these are almost always leaking when I help someone. My own most recently and after 6 months.Any sources appreciated
Sooo.. the short story is I relocated my alternator and im not getting any voltage out of the alternator. The idiot light also does not turn on.I verified continuity from the B terminal to the 80 amp fuse then all the way to the battery itself.I then verified ground continuity from...
I had someone send me a billet CAS cover but when it arrived it didn't fit because mine has a lip that the cover sits on. Cover has a groove built in. He swears his does not and is flat.Is there more than 1 style? Mine looks like this
****FOUND THE PROBLEM****I'm cleaning up someone elses mess and they had set boost cut.... I never use it so didn't even think about it!
*****I have been trying to help this guy tune his car remotely and we have things close, he is using coil on plug against my advice and already had one go...
Ive been trying to find what could have caused all this oil mess. It has drips running all the way down.It doesnt look like cam seals and wiping finger along the valve cover there is no oilIts stumping me...
Im hoping for some insight.Im painting my bay and the factory seam sealer doesnt appear to want to let the paint dry. After 2 days its still sticky.Any advice or do I just have to wait the drying out?I did scuff and clean everything. Its just the sealer im worried about after testing some...
There is 4 holes in the bay on either rail that should be plugged. I have 2 but couldnt find where to source these.Last owner had some sort of tape over 2 of them so that has to go
When installing this it looks like I have to relocate the ptu...my tensioner arm seems to be blocked by the bracket. Has anyone else had to do this and if so where did you put it?
Short story.. lost oil pressure(6psi) so shut car down immediately.Pulled motor to go over it and found this in the pan.Now I know there is a debate on yes or no to squirters so Ill leave that oit of this.Since our 1g squirters are now discontinued as of april 2022 can I use the evo 8s...
This was a butt pucker project. It took me 18 months to get this hood. 1st time it came shattered. So here we are 18 months and $1200 later and Im going to drill holes in it... it doesnt even come with a factory catch so no choice!Drill these holes out next to your headlight tabPut grease...
Im sure there is others out there but heres mine.This pan is solid. Thick flange that you will never dimple. Plenty of meat if you want to add sensors on it as well.Upon filling the trans back up I needed a full 8 quarts to top it off. This was not a full flush just a drain and pan swap.My...
I have come across someone who mainly produces honda carbon parts but if as a community we could get 10 or more interested in a part he will build them for us. As far as I can find we only have carbonetics and while good it took me almost 18months to get my hood and was shattered the 1st time in...
All of a sudden my car started idling at 10plus afr on tbe gauge with a cel. Link listed as volume air flow circuit malfunction. I then started looking and a bunch of stuff is all of a sudden greyed out. Everythi g is connected and car was fine a week ago when warming up. Hasnt even been driven...
I have my car apart and want remove the ABS harness (i know it runs through fender). I also know the door switch 2 wires are in there and there is some wires that look like they run behind the speaker (maybe actually go to the speaker?).What wires (and colors would be helpful) do i need to...
Finishing my seat belt conversion(b pillars on the way) but curious what this box is. The other side was the headache belt box... just not sure what this one controls. Might as well delete anything I can while im gutted
On to the next issue...Im doing a swap with canadian belts and of course these 30 year old clips are all disentgrating...Is there a source for new? Looks like 2 style of pop clips and one with center push style
I just received canadian belts from a member here. I know they worked in his car. But now that they are in my posession I cant get them to pull out more than 1/4 inch at a time. They retract fine. From all I have read they may need to be unlocked. Any one done this on these?
I couldnt seem to find much but I have the passenger seat belt that has quit moving. All door switches are good and turn lights on and off appropriately.What fuse(s) apply to this? Any help appreciated as I hate electrical.. but Ill work on it.
I got my middle section back from a shop and the plastic parts that allow the thing to screw to the trunk are missing. Is there a replacement for these I can order somewhere or am I stuck making something out of jb weld
Looking at aset if rotas bit i keep seeing threads about 30 and up offset. These are +20... will they fit?https://www.wheeltech360.com/ROTA-Wheel-Grid-Concave-15x8-5x114320mm-73mm-Hub_p_387.html