I ended up working with DSMPT on getting the parts I wanted. He really helped me out with making sure of what I wanted. The machining is going to be done locally and I have an option for side work to reduce the cost. I'm not expecting race shop quality however the machinist has expirence.So...

Like danl said the knipex pliers are next level. I'm a diesel tech and sometimes I risk impulse buys. One of which turned out to be a set of those pliers. I even got the 36" pair. So helpful!For me I'd say the power probe tek pod light set. (PPMWL1000).

Ok I'll check them out. Need to do more research on o-ring setups though. Called boostin' and got a wonky quote. Still open to whatever at this point. About how much did you pay for one head between shipping a core and return shipping?

Thank you sir. I'll make some calls and post what route I ended up going

Hey guys I tried browsing through the sponsors at the bottom of site page and didn't quite find what I was looking for. I'm looking to spend 3k on a head for a 6 bolt but don't trust many of the options listed by googleI want 600 whp for the block I already have built. I don't wanna build my...

This one runs at 3600 rpm at all times

Found some basic wiring diagrams however these run off of lp gas and the controller is proprietary so I'm not sure if the pin out means anything but still kinda cool. I will be looking for the engine manual. Maybe I can get the shop to order it 🤔

Thanks I'll just keep going.

Hey guys just having a lazy Sunday trying to figure out the best stuff to polish this aluminum smim. Any suggestions? My friend has a vapor honing cabinet but I'm not sure it will fit.Also I don't know anything about this intake. All I know is it's old. Any information would be greatly...

so the funny thing is I have a full Service Manuel on it and this one was produced in 2015. I'm going to dig up as much info as possible. Maybe even post some schematics and diagrams that would help anyone out.Double post sorry. This one is hilarious when it starts up. It has a coolant...

So this was new to me. I was at work out in the field and I Service and repair generators of all sizes. Everything from personal 5kw Hondas to quad supercharged and quad turbo 16 cylinders.Then I'm at one and I realized the model number on the block. I was like wth? Then I looked at the valve...

Update: roughI had some more correspondence with them and as best as I can figure from some snap on one key resource is the main ecu has parameters for adjustment and execution for all other 14 computer modules on it. The tune for the trans is also controlled this way. My trans may have...

Update: no Bueno.So I had paid a 3k deposit upfront and made arrangement with them for shipping. I pulled the trans in 10 hours with my fiancé, roped it to pallet and sent it off.They got the unit and tore into it and it had been damaged pretty bad so my quote was revised to 5700$ that...

By chance do you remember if your throughout bearing and or the pilot bearing were the same width as the replacement parts?

Yes sir! But be careful how far you open the lowere bleeder because if you put enough vacuum on it, it will suck air past the pipe threads on bleeder

Hey there I'm not to active but I have dealt with this as well. I stayed late on a Friday night at a shop I worked in until the sun came up on Saturday trying to bleed a dsm clutch and I got it! The manual says you have to have a clean bottle of fluid with a hose running off the bleeder into it...

There aren't any real junk yards around here. If I did get you one of those center sections I'm not sure if the blades survived the dump into the roll off. Also can a 4g63 turn something meant for a 15 liter efficiently? ...but seriously

The owner at my shop used to try and be frugal with parts but he has grown frustrated with junk sitting around. He even tried to sell all this stuff for nothing. When it didn't sell he tried to give it away and still none wanted it. In this bucket there are 4 large ball bearing turbos, 3 cat...

Does it count if the car had been sold to me without knowledge of any mods on it?10 years ago I was looking for my first dsm and I found one in Minneapolis for 2500$ only issue was it had a bad alternator and and needed a battery.I lived in north Dakota at the time and thats 5 hours to...

WOW I love this forum, I scrolled down and clicked the link to jacks. Thats good stuff. I ended up calling them and spoke with a lady. She told me about 6 weeks is average turn around time and that they are flexible with payment at beginning or end of build.Thats pretty cool in the case of...

Alright I'm glad to hear your experience, Im Going to email them and I will report back

I was browsing the ralliart specific forums and there is no traffic or recent posts about it. I was really wondering if anyone here had any first hand experience with pulling the trans, or using jacks transmissions rebuilt units.For a new trans from dealer is 13k. The parts guy laughed over...

Hello all, I'm fairly inactive on the forum but I I do own a dsm. My second one actually. I also own a 2010 Lancer ralliart I traded a bike for for.Its been tuned to 270whp at map but maxed out there because the clutches were slipping. And not long after the dreaded p1832 code came up and...