Good working 2g awd 5 speed trans with matching t-case with new OEM trans mount. Transmission case has a 2 inch crack near the front mount. I would recommend to weld it vs JB weld. $400 located in southern indiana. Thanks. Text would be better as I dont get on here much anymore. 8126393213. I...
Lightly used vrsf intercooler (10 miles) and a aftermarket front crossmember bar with poly front mount. Asking 150 for intercooler and 100 for crossmember. Prefer to sell semi local. PM or text 8126393213
Looking to clarify some information on 2g auto flexplate spacers. I've found some information on 1gs with autos that show a spacer between the crank and flexplate then a spacer after the flexplate before the bolts. I've found one thread on a 2g, which shows one spacer after the flexplate between...
A set of 2gb eagle talon fog lights with brackets $135 shipped and paypal.
95 manual transfer case with both seals replaced $150 picked up.
1g TB rebuilt last year, painted black but chipping away with ports welded shut. $110 shipped and paypal.
ETS Street intercooler in 4" for an Eagle Talon that retains that stock fog lights. Supports 500whp claims from Robert at ETS. $350 plus shipping and PayPal.
Question for anyone who has installed these to the inner cv cups. The kit comes with two packs of clips, one is a C-clip and the other is a thin lock washer. I know the C-clip goes after the tripod bearing, but what about the thin lock washer? Here is a pic of the pieces.
Need some clarification on 2g Prothane bushings. I found some older information that says the bushing are the same, just not the the roll stop inserts. Is this correct? The Prothane part numbers are 13-501-bl and 13-503-bl. I'm looking at replacing the mounts with Prothane bushings with an OEM...
As title states, does anyone make stainless steel 1g bov flanges? I found a few companies that make them out of aluminum, but I haven't seen any in stainless steel. I have a set of ETS intercooler pipes with a Greddy flange, and I'm looking to have it removed and have a 1g flange welded in.
1). Any boost, vac, or exhaust leaks?
Boost leak tested 5psi above your max boost with no leaks?
Yes
2). Verified mechanical timing?
Yes
3). Verified base timing?
Yes
4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: Ngk, over 1 year
Spark Plug brand, type and Gap: Ngk Bres 85)...
I drove my car to the store about 1 mile from the house, and I notice that the front end suspension started to make a lot of noise. The noise it self sounds like something is loose as in rattling and clunking sound at very low speeds of 2 mph or greater. Needless to say I parked the car and...
I have a question about Nabco clutch master cylinders. I know that Nabco was the OEM Mitsubishi part company used, and I was wondering if there was a difference between getting an OEM one for $120 and ones that are $60+ from ebay. I don't use ebay parts on my car but if it's the same part why...
Hi, everyone I've been looking for some front and rear full polyurethane motor mounts, only to find out that there isn't any good options. However, I found that black_gst (Adam) used to make some for 2gs awhile back. Currently he does not produced them anymore, and I've read a lot of problems...
I'm looking at ordering some bigger injectors. I've read that the FIC hi z 2150cc have some rust issues if left out. However, I don't plan to have them sitting out. Does the R.C.I 2200cc have any problems, like how's the tuning with them? I run mainly e85 with my current FIC hi z 1100cc. I have...
So I'm trying to install an ETS 7' street intercooler on a 97 Eagle Talon, and it's not fitting with the stock fog lights. Is there something special you have to do to retain the fog lights? Or does anyone have step-by-step instructions for a 2gb talon install? It seems the intercooler is too...
First off, sorry for posting this in the newbie section, but I don't know where to begin the search for this. There seems to be a metal line with nothing connected to it passed the transfer case and by the driveshaft. I'm looking for a leak and it seems to been leaking for awhile judging from...
I've got a question about some enkei rpf1 rims that I ordered. My question is will 17x7.5 +45mm offset fit just fine on my 2g awd? According to the website that I ordered them from it said it did. Also, will my continental all-season tires from my gsx rims fit? They are 215 50 17. Thanks.
So today, my seibon carbon fiber hood decided to say hi to me by coming up and smashing my windshield LOL. Luckily, I have a full coverage and already have someone coming to install a new windshield, but my hood is cracked and chipped. I will be talking to my insurance agent tomorrow, hopefully...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
No, tested at 25psi
2). Verified mechanical timing?
Yes
3). Verified base timing?
95-96 Cas 2g
4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: NGK wires, few months old less than 1k...
I'm going to install a gm flex fuel sensor with Russell push lock -6 an fittings. I want to know if I can just put it in the bottom of a fuelab regulator or do I need a Russell -6 an swivel adapter to give it a little more space? Thanks
Hello, I wanting to hear some thoughts from mk3 supra owners about their community and their cars. Yes, I understand this is a dsm forum but people can drive both.Background: My first car was a 87 mk3 turbo, and it was what got me into working on cars. However, it's been almost a decade since...
I'm looking at replacing my front and rear suspension besides the struts right now, and I have some questions on which to get. Extreme psi has the OEM front kit with knuckle for 130 per side and rockauto has Moog parts. Which is better OEM or Moog? Also which is better Moog control arms R-series...
So I just received my new replacement manifold because of a bad coating on the last one, and it has a knick in it were it was filed down. It can be seen from both sides, plus there's a hole in between the runners. However, I don't believe it goes all the way though. Here's some photos and would...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
Nope tested at 25psi takes about 5 mins to bleed out
2). Verified mechanical timing?
yes
3). Verified base timing?
yes
4). Ignition system
COP or Stock Coil: Stock coil
Wire brand and Age: Ngk
Spark...
I've recently installed a rebuilt Evo 3 16g by JusMX141 along with several upgrades, and I can't build boost at all in the 3k rpms or only 7psi in the 4k rpms. I've done several blts with only a few small leaks founded and fixed. Around 15-20psi on test there is a whine sound around the turbo...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
BLT to 20 Psi, only leaks above it at the intake manifold to afpr but bought small clamp to fix instead of zip ties.
2). Verified mechanical timing?
yes
3). Verified base timing?
yes
4). Ignition...
So I'm about to start up the new turbo, and I was reading about priming the turbo. I took the top oil feed line off to check if oil came out while trying to crank the car over and nothing came out. I remove the whole line but left the 90 degree fitting in the housing (can't remove it to save my...
Ok so I was installing everything back together and my vrsf lower pipe can't connect to the j pipe because it hits the dump pipe from the stm o2 housing. My question is will an ets j pipe and some different couplers move the pipe off and away from the dump tube or what are my options? I read...
I'm trying to install a walbro 450 e85 pump and need to know which wires I connect the walbro harness to. Which wire is for the positive and negative? Here's a picture of the stock plug in to connect to.
I bought a STM intake kit to run SD without a MAF, and was wondering what people do about the line for PCV on the valve cover? I still have the PCV valve going to the intake manifold. Do most just run a catch can for that line or should I get a nipple welded on the intake pipe to still run it...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
None only tested to 18 psi. I run low boost til upgrade
2). Verified mechanical timing?
yes
3). Verified base timing?
yes
4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: Ngk couple...
Where do I buy a turn signal flasher relay for a 97 talon? I replaced my turn signal switch today because my driver side turn signal wouldn't stop blinking. My flasher unit was making a lot of clicking noise while it was blinking, and I tried to replace it with one I got from O Reillys but it...
So I'm looking to upgrade my turbo to either a 20g or a fp hta68, and I can't decide which to get. I've been to talking to Justin on which turbo would be best for my needs, and if I go with a 20g I'm having him build it for me. My goals are to have a fun street turbo for DD as I don't race my...
I have a question about if I can install PTE 1000cc injectors with an Evo 9 fuel pump without an afpr? I'm only running 18psi or less of boost with a 14b turbo. I'm currently running Evo 9 560cc injectors with Evo 9 pump (rewired). Also, I tune with ecmlink. I will be getting a Fuelab 515 afpr...
I'm trying to install two innovate gauges, one wideband and the other a boost gauge. I'm using the same power locations as the old gauges were used in the fuse box. However, those were installed by the previous owner and I thought I had it right but my gauges constantly have power. My question...
So I have a chance a buy a wreck 99 non turbo auto with black interior and I'm wondering from the few crappy pics I got if all the interior is actually black. ( Yes I know it's actually black with gray in some spots.) Take a look at the photos and let me know what you think. Kinda looks like the...
I have a 14b turbo with a stuck manifold bolt. Snapped off at the top and I've tried the double nut method with no success. I don't have a torch to heat it but my question is should I have a nut welded on or just take to a machine shop? Hopefully this is the last broken bolt for now. Thanks
Ok so again this was like this before i got the car. Po broke one of the exhaust studs in the head and did a horrible job trying to fix it. What can I do to fix this? Looks like they tried to drill it out but with a big bit because all of the threads areally gone. Any suggestions would be great...
Ok so I was lied to about my exhaust from the previous owner about the size of 3" from o2 back. Well I took off the the o2 from the downpipe because the gasket was shot and notice that the o2 is a 2.5 and the downpipe is 2.75 but was using a 3 gasket cut to fit. Now the end of the dp is a 3 so...
I have a question about a 2g awd fuel pump hanger asembly. I removed my assembly to install an evo 9 fuel pump, however, it already had a supra tt pump but the connector to the pump was cut to hook up the wires to the pump. My question is would a walbro harness connect back to the assembly to...
I'm installing a new fuel setup next week and was wondering what would be a safe boost level for daily use? 14b turbo with a vrsf intercooler and ecmlink v3 to tune with. Fuel setup Evo 9 fuel pump rewired, new fuel filter, and 680cc fuel injectors. Will be also installing a new innovate mtx-l...
I'm installing a mishimoto radiator and slim fans with shroud. I'm wanting to know how to wire them up to where both come on without a switch. Any pictures or diagrams would be great.
I'm wanting to know which out of the two widebands would be best for ecmlink v3. Innovate 3873 DB or the 3845 MTX-L? Still debating if going to place in front o2 and simulate narrowband or just have bung welded on the downpipe or use rear o2 (no cat).