Iv been thinking about the benefits vs annoying stuff when building e85 motors. Id like to hear personal experiences with it.I can start with mine. Its superior good stuff for cars that are mostly build for power and not daily drivers. Iv been using it prolly for last 8 years in my dsm and iv...
Hi!
Im having weird problem with cold start oil pressure. Car idles fine, my electrical aftermarket oil pressure gauge reads normal but suddenly drops few seconds to zero and back to normal. Dummy light does not come on however. It happens couple of times until engine is warm and wont happen...
Hey. Does anyone know if 1g and 2g share any parts like steering gear pipe that runs fluid to passanger side? Mine is now mostlikely cracked as its leaking. I think there is no oem number for this pipe so either need correct used oem pipe or diameter of pipe and fittings size.Thanks!
I would like to hear ppl experiences with lifespan of tuned motors in dd with mods and how many miles driven.My current motor is:
E85 10.5:1 wiseco hd
Fp green @18psi
Liquimoly 10w-60 full syntethic.
Bs delete and pretty high oilpressure (105psi @7krpm)
10000 miles on daily driving.
No...
Heya!
Whats your intake for removing catalytic converter? I was running 3" catalytic converter got tired of it as i was thinking its pretty worn out and restricting after it has been under car for 3 years. i was pretty suprised how much lower end torque this removal made (pretty noticiable). I...
I just wanted to create thread about this common issue with these cars. This is a problem that will create alot of frustration untill you really get problem pointed out in to altenator (having volt meter in dash is a great idea). Melting altenators has bring alot of idle and tuning issues to me...
Hi!I have been trying to wire prosport wideband in to ecmlink v3 today as narrowband sim. I soldered 0-5v in to ecu pin 76 and analog output ground in to sensor ground pin. In ecmlink ecu input page i did set front o2 as narrowband sim and selected front o2 as WB and saved all the changes. How...
Hi!
Im having some major problems on cold starts with e85 10:1 cr. I fas fine running this setup a year ago but now my issue is not firing cylinders 2&3 on cold starts. Iv got new coil new plugs new ngk wires new power box next to coils. Tried different gaps on plugs. I can get car running...
Hi!
Any one here running enkei rpf1 on 1g awd? I am interested to find out experiences between different width wheel and offset combinations. Im thinking of purchaising either 17x7.5 48 offset enkeis or even 17x9 35 offset.
The problem is that i do think that mostlikely there will be huge...
Hi! Im looking to buy driveshaft with all parts including carrier bearings and mounts for 1g awd dsm. I cannot find these parts in europe anymore and im missing all parts from front transfercase to rear diff. Been trying to search internet but all i can find is aluminium driveshafts whitout rear...
Hello!
Iv been having some "issues" with fp green flange threads. Seems like everytime i take turbo apart from manifold it breaks threads from turbo. Its anyoning to pull manifold out to repair thread with helicoil. Never had problems with mhi turbos. Any work around this issue as i dont want...
I probably have a minor head gasket leak to coolant. There is stream of bubbles after burbing system well. Also tried taking injector plugs off and crank engine. Still some bubbles. Still need try leak down to verify cylinder number. I suspect my block or head surface was not machined enough...
Has Any one installed MD015988 on spring to their car? Interested of outcome. I have evo3 ofh w/o porting and idle is fine 14psi. Seems to shoot around 100psi at 7k with 5w-40. Just looking to get it around 80 without lowering idle oil pressure. Any good ideas? How much 30w oil affects? Thanks!
Hi! Is there list of oe numbers of thermostats. I asked mitsubishi oe parts dealer and they said there is only 180f thermostat. Im Running mishimoto cooler and idle temps are normal 190-208. When im driving my temps drop to 180. I wonder if its faulty thermostat or too good cooler. I would like...
Hi. I was wondering what world be safe timing map for new engine with 10.5:1 cr and e85 fuel. Is it ok to use stock 2g map or do i need to lower it with this high cr. Just need to break in before dyno adjustment.Thanks.
I had to cut my front bumper to fit larger cooler. I did not like the idea of just cutting extra material out as it would leave upper part of bumper missing. I made new cover to fill gaps between bumper and cooler. I still have bumper to paint and install it but here is what i have done so far...
Not able to view ecm tuning website. Have been trying to check some injector info but not able to open their pages. Any one else with same problem or just me?
Hi!
I would need exploded view pictures for 1g transmission.
Car is 91 gsx and transmission is KW5M332NPXV. I'v been looking for it around internet and i'm either stupid or there ain't too many around. I bought car that has this tranny disassembled and i need to put it back together...
If there...
Hello!
I'm looking to buy tsi awd talon 2g 95 in Europe but i think i might need paperwork that states its emission approved in usa to register it in my country. Is there anyplace i could try it get it from in usa? Is there any stickers in enginebay that states approval?Thanks!
Im upgrading to diamante front brakes. I have everything else (pads, discs and rebuild kit for calibers)
Still wondering what oem brake hose would fit in to sigma caliber and 2g brake line. If some one knows oem
part number i would apritiate it, cheers! Tried to research but could not find oem...
Where can i find front o2 sensor with only 2 wires coming out?
my 95gst oem sensor has only 2 wires and 2 pin connector in it so there is no heater.
I would like to find one with right connector so i would not have to cut wires, but every sensor seems to have 4 wires.Thanks
Hi!
has anyone re-routed metal coolant pipe in 2g that goes to oil filter housing?
Can you replace this oem pipe without taking taking out bolts that hold turbo in exhaust manifold?
I don't know would it be bad idea to run coolant pipe next to oil pan to other side and then straight up to...
Hello!
I would like to know if any one has any experience with evo 9 pistons valve clearance in 2g. I did measure c/r 8.3-8.4:1 on stock hg (0.0511) with evo piston. I want higher c/r with these pistons, and as they are about 0.070 lower from the piston head than 2g piston, i could mill out...