please get the right ones lol

+1

+1 much cheaper than an engine lol

act 2300 is a good PP to start with just make sure you dont use a 2700 if you are a 7 bolt on stock internals as you might crank walk. As far as the 6 puck disk, I had one on my G35 and it was great, just took some getting used to. Breaking PP fingers is relatively uncommon, or atleast ive never...

could be the wires that feed the signals from the sensor.

Either get stock injectors or tune it!

I have a 16g and went EWG with punishment racing recirc housing with no problems holds boost rock solid. Just make sure you either cut out flapper or weld it shut depending on where you put EWG. Make sure if you go that route you get a good piece (tial, turbosmart, etc)

you can find running engines pretty easy for about 400-700

check a fuse LEDs overpower standard fuses easily if theyre not the proper wattage

yes flywheel and starter plate then good to go

looks are not always accurate, on my 98 gst the belt looked perfect then shredded while driving.

If it is a 420A block then it is good for use as far as I knowjust make sure you use the proper internals and parts

misfires maybe?

falken ziex are decent tires for DD and mild performance

redline 75-90

clutches are same, you chould check out southbend clutch they're pretty good and inexpensive

I have some things waiting to be installed and im wondering if my setup once tuned will be able to support 300whp.PTE 880cc injectors Wally 190LPH Evo3 16g w/8cm fp housing PR FMIC kit Extreme psi Intake tube/filter Ported Evo3 mani full 3" turbo back exhaust EcuFlash/ceddymods tuning...

Really loud= external wastegate with atmosphere dump+3" turbo back exhaust.Loud= 3" turbo back exhaustKinda loud= 3" catbackNot so loud= gut cat and cut muffler off

Thanks for your input, the whole bottom end pulleys and all are new lol

In a couple of months i will be PCSing from utah to aberdeen,md. It is a 2200mi drive, i am wanting to drive the eclipse because it handles snow much better than my g35. Im in the process of rebuilding the engine, i have a real mhi evo3 turbo i just rebuilt, and im swapping all hoses/belts for...

Ahh thanks alot had me worried it was messrd up lol

Im rebuilding a MHI big 16g and i opened it up and found that there were no small snaprings inside holding the bearings in place, there appears to be a small lip that holds them. I dont recall ever seeing that before however my last rebuild was on a 14b. Anyone know if i should be concerned or...

Might be brass fitting on back of gauge or you could have a crack in the plastic.line

Found a good kit many people on here have been buying, importevolution sells 11p kit and everyone had good things.to say about it. :D

so i found these for $60 would these be fairly decent compared to cracked and falling apart rubber? Silicone Radiator Hose Kit for Mitsubishi Eclipse DSM 4G63T 2G 95 99 Blue | eBayand these for 75 https://www.rtmracing.com/xcart/product.php?productid=18751&cat=1730&page=2

possible that part of that shredded belt got wrapped behind the pulley? had similar thing happen on my old 300zx

I have glowshift boost, oil pressure, and water temp they're pretty accurate i compared to a buddies autometer for the boost gauge and they read the same. As for AFR i have the innovate MTX-L and i love it. The AEM isnt bad either i used that in a previous DSM

i just looked at that, and it looks pretty good. I think thats what ill go with i like the black/blue combo that i was finding looks pretty decent.I also found a site called siliconeintakes.com and they seem to have some decent things on there as well i may just pick up some vacuum hoses...

Thanks, btw you have no idea the number of ebay things hiding under that hood lol im amazed it lasted as long as it did lol. Btw dont EVER get an ebay timing belt lol

So im trying to clean up my engine bay and im going for blue/polish look, anyone know where i can get a blue silicone recirc tube and most vacuum lines? I dont want ebay stuff, im in the process of deebaying the previous owners mistakes (pos turbo blew lol)

you could use the 20g compressor housing, however that would partially ruin the purpose of a Bastard 20g since the 20g housing has a downward exit and no jpipe