I am currently troubleshooting a 95 GST auto that I recently acquired. The car will not move in any gear by itself (OD off/on). I am however able to get it to move if I put it in drive and give it a little push. It'll start to move forward low idle. However, whenever the throttle is applied I...

What's going on guys. I'm in class (for Aeronautics) and we started talking about AFR's. My teacher stated that MAX power will be when your burning a little rich.. I've always thought running a little lean will make more power, but can't explain my reasoning aside from that's what I have read...

What's going on guys! I'm redoing my suspension, and it seems my bumpstops have crumbled like most. Unfortunately there not making the OEM bumpstops anymore.. So what Aftermarket parts are you guys using as a replacement? Thanks for any help!

What's going on guys, I recently acquired a new DSM that I'm diagnosing as it is a no start. I'm following the Tech article here on tuners and have verified fuel to the rail by taking off the (2) 10 MM bolts from the rail and having someone crank the car.My issue is at the FPR I can take the...

What's going on, I've recently been thinking about swapping wheel color on TheBadHabitZ. The black I currently have is a little to stealthy for me, and I was curious if someone could help me out and transfer this Bronze onto the car.Here is the link to the color I'm thinking.. If you have...

Hey what's up guys, been awhile. I am currently rewiring my knock sensor, and have a few questions. From my understanding the white wire (from the female side of the knock sensor pigtail, by the intake) goes to pin 78, while the black wire goes to ground. Does there need to be a specific place...

We'll guys, it's a sad day for the DSM. I got in an accident. I started to replace things wrong, and ran into a problem.. The subframe holes are bent, and won't allow one of the bolts to go in.. I'm unsure on how to tackle the situation. I've tried putting and old bolt in and pulling on it to...

Hey what's up guys, for some reason I'm having issue with my rear lower control arm. I'm able to remove everything aside from the bolt closest to the dif, I can't seem to push the bolt out. The gas tank isn't allowing it to be removed. I would understand if the hex part was towards the back, but...

Whats up guys, having an intermediate problem. It seems when im WOT I have oil that comes out. It looks to be coming on the upper right stud by the timing belt. Im a bit confused, as I thought the center right one was the only one that goes into a oil Gallery. Perhaps its somewhere else by the...

Whats up guys, im in search of another DSM, and came across this one. The outside really isnt my style, but from what im hearing the motor its self seems to have some work done. He said he purchased it off of his friend of whom built the car. He says that he has recipts, and will show them to...

This may seem like a silly question but I'm parting out a DSM and I'm trying to get everything I can for it. That way I can purchase another. I'm going to be scrapping the body hopefully getting some kind of money for the metal and was curious if it would be worth the time to take the insulation...

What's up guys, well i finally completed my Manny to Auto swap, almost. I have everything in, made sure TC was in all the way, everything was tightened to spec, fluid in everything, rear dif, t case, trans. I go to start the car up and it makes a hideous knocking sound coming from the trans...

What's up guys!! Almost done with my swap to auto thanks to this forum, you guys have been a big help, and a huge information database. Unfortunately I have a few questions that I can't seem to find. The Auto assembly has 3 wires, one for the gear selector, and the other two are for what? I am...

hello hello. Hey whats up guys I have a 95 GSX transmission auto that got shipped to me and during transit was dropped and the studs bent on the bracket that go into the passenger side motor mount. So I went to the junkyard and grabbed another one not knowing that the spider Trans Bracket is...

Hey what's up guys!! New to the Auto Trans and had a few questions! I purchased the trans used, and of course want to be sure it is in fair condition.1. What amount of play in and out is acceptable in the outputshaft. Here is a video of my current.2. I noticed this crack on the housing, I...

What's up guys, I'm in the middle of my Manual to Auto swap and figure a Cooler would be a good idea. Instead of going with the stock cooler, I decided I might as well just upgrade. So I went to the IPT site, chose our car and was looking at the coolers (about two weeks ago). I finally decided...

What's up guys, I'm looking to install my kiggly flexplate here soon and my oem 2g flywheel bolts, although grounded down seem to get stuck.. I figure the threads are mangled. I'm curious if anyone has ever tried the evo 8 flywheel bolts, as they as the correct length.. I'm just not exactly sure...

What's up guys, swapping my Manual non lsd dif with an Auto Non lsd I picked up. I had a few questions, for one what is this plastic piece that's on top? I can spin it, is this kind of like an overfill?.. also in the other picture you will notice that the axle doesn't quiet go into the dif all...

What's up guys, I keep reading that our AWD Auto Trans takes, ATF +4 Dex Merc, Spec II Spec III.. I'm beyond confused at this point. I have 6 quarts of Dex/Merc at my house, which would be great if I could use those.. if not then I was going to pick up this. The picture below, I would assume...

What's up guys, pretty simple question. Just curious in what orientation does the Pilot bearing get installed.. as one end is thinner than the other.

whats up guys I got my car about a year ago with a 2100 Street disc and an OEM flywheel. Shortly after I got the car it started slipping. So I replaced it with an act 2600 Street disc and OEM flywheel resurfaced and stepped to meet the 2600 specs. After the clutch was installed I did the normal...

whats up guys I've grown tired of my manual transmission due to the fact that I have to replace the clutch after about a year of track/street use. So Instead of using the money to upgrade my clutch I think would optimal to switch to automatic transmission. It seems that there really isn't a...

What's up guys, I'm in a little bit of a bind. For quiet some time now my CAS has allowed my car to start, and other times not so much. If I tap on it it will crank up shortly after. Well today it decided to quit all together. I can tap it but it will only start idle for a second, and die. I'm...

hey whats up tuners I had a quick question I'm getting ready to sandblast my 2g GSX rims. I'm unsure if I need a clear coat after I didn't notice any clear prior to getting the car the rims were not shiny. Is this is this a necessary step after sandblasting in order to prevent them from rusting

hey guys I'm currently having a clutch problem I have a2g GSX with an act 2600 clutch and resurface flywheel which is about a year old. From the beginning I was having problems getting my car into gear if I adjust the clutch properly I can get into a gear and drive but if I went wide open...

What's up guys, I can't seem to solve my problem. I stated getting flutter recently on my 1g BOV at around 25 pounds. I have no boost leaks, replaced all vaccum lines and reseated my BOV just to make sure it was all good. I'm at a loss of what I can do to get rid of this flutter, it's only when...

What's up guys, upon searching I thought I found my answer, but it was followed by another.. Does the "air" hose just vent to the air? I don't plan on smogging my car, so will it be okay if it's left as is? Here is the thread, and here is a picture of the canister. I'm looking at the nozzle to...

Sup guys, just curious if anyone has a magnetic wall.. I lose bolts all the time when doing builds and was thinking it would be much easier to label things if I had a magnetic wall to stick bolts on and write what they were on the top.. Anyone have something sinular?

Hopefully this is the right sub section.. Well I purchased a 55 Gal drum which had methanol in it but had been sitting for some time.. I see what looks like gunk inside the barrel, and was curious the best way Togo about cleanin it so I can then use it for my e85. Should I use some kind of...

Whats up guys. Thanks for stopping by, I'm upgrading my brakes to the Outlander BBK. I am buying the bracket and rotor. I know that the GSX and outlander use the same caliper but I would like to purchase new ones, I'm curious if I should go OEM for rotors/Calipers or will the good ol Duralast do...

What's up guys! I purchased my PR kit which came with the Knok off Greddy and of course the intercooler. The upper pipe has slots for the knock off, and a 1g. I currently have the 1g on there with some RTV and the gasket but when I perform a BLT I get air that wants to come out of the holes made...

Hey what's up guys, I recently bought some new hardware and started threading them into the turbo. Well when taking them out one of tem dexided it was going to be a PITA and cause tention. I had to use a cheater bar to get it off. Well coming to the last one (with new hardware) it went in until...

Hey what's up guys, I'm just trying to see if anyone has any pictures of their door jams and side skirts.. I recently took off a body kit the PO had on and am a bit stumped. I put the OEM sideskirts on but it seems as if they should be molded to the car (inside the door jam). Also, is the front...

Im lookin for the 3d Model of the 4g63 so I can pull it apart and actually see what is what.. Perhaps it was the car itself but I remember seeing this not to long ago. I thought it was on vfaq but I can't seem to find it, can anyone point me to the right direction/thread?:hellyeah:

What's up guys, got the car about a year ago now and decide I'm finally tired of the remote alarm start, and I want to remove it. The provlembeinf is I'm in the middle if a turbo swap (waiting on turbo). This is a problem because courage veing a remote start I'm assuming if icut somewhere it's...

What's up guys.. Well, just got everything installed and was so stoked! I figure logging would be a cinch. I'm having a problem with my MTXL wideband logging inside of DSMlink. I have seen countless threads about putting the brown wire into the 76 pin if you have the wideband in the front 02. I...

What's up guys, I'm currently working at the Shell Station there at 41/Grangville while attending school.. I was talking with my boss about the possibility of 92 octane, being that it's to uncommon around here. She agreed to talk with the owner of the store about it. The problem lies with...

What's up guys, I'm currently working at the Shell Station there at 41/grangville while attending school.. I was talking with my boss about the possibility of 92 octane, being that it's to uncommon around here. She agreed to talk with the owner of the store about it. The problem lies with...

Hey guys I'm lookin for a place that sells 92-93 octane in the Lemoore or Hanford area.. Fresno if I have to.. Or a way to get it, the 91 here really limits the tune.. Maybe buy it by a barrel or something.. Anyone around here have a suggestion? I tried to search for a gas locator but tht did t...

This may sound weird but I recently got dsmlink, and had the launch limit at 4000. I launched it with the exhaust off (because it was being welded) and it was amazing! I put my exhaust back on today and launched it and it now wants go stay in the friction zone for a bit before it takes off.. I'm...

Hey guys, got my MTX-L not to long ago, about 3 month now was running great until a couple days ago. I randomly got a e3 code, for wire short or possibly bad sensor. So I replaced the wire to the gauge as well as a new sensor.. Same problem as before. Solid ground and power.. I've read a few...

Hey guys, well I was removing the door cap to move it lower, to match the stock OEM front, and back bumpers (previously a bodykit) and the spot in which the plastic's would fit in actually broke off, from age I'm assuming.. so now I'm stuck with trying to figure out how to put them back on...

Hey guys, well I have a few questions.. My car is throwing the code p340, but it doesn't throw it when it's trying to start, it will toss it wheny car sputters in the higher rpms.. Figure this was a fuel filter and its being replaced.. But any idea as to why it would throw it then rather than...

Hey guys, for quiet some time my car has always had a "studder" before it starts as Shown in the video (listen closely). But recently when it starts up it feels like its running on two cylinders, and after a couple seconds of being on the gas a tad (in nuetral) it will rev up and idle as normal...

Alright, I just got my wideband in the mail and figured it would be straight forward.. Unfortunately for me it's not. I understand that the wires areRed - Ignition Wire 12vWhite - Is to dim the light, which I'll be grounding insteadBlack- Ground wireYellow- Analog out 1Brown- Analog...

Whatdup guys! I decided yesterday to take out my Amp, take out the tail lights to fit my bumper and gut my car. I took out ALL wiring associated with the amp. I put a 15A fuse inside turn the lights on for the dash and tail lights and it pops almost instantly. So I figure okay, pull the...

I've seen countless threads but none really adhear to my countless situation. I put in a new PP,Act 2600 Clutch, Machines the Flywheel stepped it, new pivot, new slave, SS line, new TOB, fork, clip. All OEM Well now my clutch is SOFT, ive bled the clutch countless times, and have properly...

Hey guys, just a quick question while I'm putting in the new ACT 2600 clutch and street disc.. I have a new fork, pivot ball, slave, flywheel bolts, OEM TOB, retainer clip. The flywheel is resurfaced and machined to spec of .612. My question is should I throw a 1mm washer under the pivot ball...

Hey! Replacing my clutch and these boots decided to go on me, just want to make sure that this video is a good Step by Step, figure it would be better to be safe than sorry.. I found the kit he was talking about as well.. Any inputs appreciated!YouTubeCV Boot Kit | 1997 Mitsubishi...

Found a few threads on why there would be one AKA Track. But the job that was done was half assed.. Quiet a bit of wiring issues. Anyways my question is other than track is there anything else I should keep this for? I also might update this if I find a few more hack jobs if that's okay.. Least...