I believe I have read all of the threads involving fuel level wires and I have the wiring sorted out for the fuel level on the Passenger side. Fuel level is yellow with black stripe (mine seems to be just plain yellow) and small black wire is mapped to the black fuel level wire. I am not sure...

I am rewiring and replacing my fuse box that is in the engine bay. Based on the diagrams that are in the FSM the pin layout of the relay makes no sense, 1-3-4-5. Most micro relays are like the ones listed below, none are numbered like the relay in FSM. After figuring out the numbering I still...

In the past, I've had issues with getting RTV in the oil pump shaft seal drain hole in aftermarket oil pumps. As you can see in the pictures below, first is a 6-bolt ACL oil pump and the second is an OEM 6-bolt oil pump. The OEM pump clearly has an offset drain hole to keep from accidently...

speedgearracing had a close gear ratio for an evo 3 on their website back in the day. I emailed them the other day and they stated they still make them. Figured I'd ask before sending my money away, they do accept paypal so it's not a massive risk.Comes with 1st and second gear with input...

Has anyone done an install of a PMU like the ones listed below for their chassis harness? I would like to rewire my chassis harness to get rid of all I deleted separate it from the engine harness. Just wondering if anyone has already done so I could get some sense where to start...

Need help Finding the rubber cover that goes over wire connected to the alternator. Part in question is the item circled in blue.

I've been searching to fill the void that exist in the DSM transmission n world. The biggest problem I've seen is the 3rd and 4th gear hub and slider. The old Heavy Duty 3/4 from the 91-92 AWD trans is no longer being made and neither is the evo 3. I have found a shop that is willing to make a...

looking for a vendor "ideally a supporting vendor" that does type 3 hard anodizing. Want to test out a theory I had, hard anodizing the mid-case to give same affect as the boostin mid-case.

I was looking for some reviews on kirkey seats and ran across this project. Has anyone seen this before?https://grassrootsmotorsports.com/news/your-projects-nelson-familys-ls-powered-front-drive-dsm/

I selling a BW S364.5 SXE turbo with 68/76 turbine wheel and .82 T3 housing. I purchased it mid May and want to sell it due to me wanting to go in another direction with turbo selection. I want the new 35RI'll post pics when I figure it out https://flic.kr/p/2g8aFRn https://flic.kr/p/2g8aVht...

Does anyone tune ecmlink in the mid-atlantic region. For a reasonable price. I've been quoted almost $1k while getting quotes. Also does exhaust work as well if possible.

I know been a while so I have dove into LSD units on DSMs but my last experience was not very good. I have a FWD 2G with a KAAZ unit that got damage when removing the axle with the circlip. This seemed to be a very common problem with new brands selling diff's back in the early 2000's, I am...

Anyone know where I can get a new 3rd brake light for a 2G eclipse spyder?

I've heard that in Richmond that there is no requirement for auto inspection, is this true? If so what is it the same for other southern VA counties? I know northern VA counties require annual.

Asked for quote and this is how they responded. http://holinger.com.au/showroom/hmlWho's down! LOL

So I put down 450whp at 26lbs does that seem low based on my setup? Check my profile, not the sold one... GTX3582R .63a/r t3

Has anybody created an AEM infinity 8H jumper harness for a 2G DSM 95-96? AEM doesn't sell them and boomslang want's a fortune for them and will not share their pinout diagram.Created a diagram of what I believe is right. Most of the evo 8 and DSM pins are the same. information used creating...

I was browsing Pauter's website and I happen to come across these things does any have experience with these and where in the hell would you get a piston for it?http://pauter.com/shop/rods/mitsubishi/mitsubishi-4g65-1st-gen-rods/

So this happened today.. Finally git the car running after a bunch of upgrades. One of the upgrades was a JMF T3 manifold that I installed with some dorman bolts and ARP nuts. Had the car running in the driveway for a few minutes and by the time it got to operating temperature I heard...

I am doing a bunch of front end work and figured I'd replace the front hub bearing while I'm up here. I purchased a wheel and hub bearing assembly but the holes for the lug nuts are the wrong size. The issue with this is that my $130 ARP extended studs go to waste. I would buy OEM but they only...

So, I'm finally getting around to installing my DSS stage 5 rear axles and noticed they can't squeeze through the tunnel the OEM axles did. Is this normal, do I really have to remove the rear toe arm just to install these axles?

I am in need of some wheels that with fit my evo brembos and and I'm about to splurge on some 17x9.5 wheels. I know according to the chart 245/40/17 should be perfectly fine on a 2G but how much does it matter on this wide of a rim? I have a 2Ga so my rear knuckles have less clearance than the 2Gb.

As the title says, will motegi traklite 17x8 +40 wheels fit over EVO brembo calipers?

I want to know if it is possible to run 3" intercooler piping on a 2G short route kit. I want to know if anyone has done this before. i was checking for room today and notice the hole I cut has frame on the left and radiator on the right so it's not like I can just cut out more metal. This is...

I was wondering what everyone's experience or thoughts were on ebay BOV and wastegate flanges. They are cheaper than the manufacturer part and it doesn't have any moving parts to break like a turbo. I'm just concerned with machining of flanges to be sure they fit properly and if anyone has had...

I currently have a DNP T3 exhaust manifold and I am contemplating ordering the JMFab T3 version with 44mm wastegate flange. Has anyone went from the DNP to the JMFab exhaust manifold or even the shearer fab unit? I was wondering of it put everything in the same place so that I did not have to...

So I picked up a T3 DNP manifold last year never used and had it on the car for about 3-4000 miles. It hasn't even been 300 miles since I got the car back together with the new swaintech coating on it. I noticed a crack right by the wastegate, it seems like a very common place for it to crack...

So everyone says that 1g and 2g transfer cases are physically the same. I know 90's had different splines for the smaller output shaft and the 97-99 DSMs has different ratio's but what is the difference between these? The upper mounting points are very high the first one, what are they out of...

So my car has been down since October for a rebuild and I was finally ready to fire it up today when I noticed that when I attempt to turn the engine over, the wheels turn. The wheels turn when the car is in neutral and when the clutch is depressed. Only thing that was done that could affect...

I installed a new 2G rear diff, axles, solid diff bushings and subframe mounts over the weekend and I ran into one issue that concerned me. When I attached the driveshaft to the diff it was a tight fit compared to the removal. I am concerned that I drove the solid diff mounts in too far and the...

anyone order from dsmparts in the mid-Atlantic region? I ordered a clutch, flywheel and a fork from there and it came literally the next day. Anyone else have the same experience? Seems like they have a wherehouse in the area.

Anybody check out the new GTW turbos? The price looks great and they are using ceramic ball bearing center sections now. Those prices make me feel like it's 2007 all over again. I ended up buying a GT35r and having it upgraded with a GTX3582 wheel, I'm kind of having buyers remorse now...

So my motor blew up in October and the engine is almost completely rebuilt. My next order of parts will be my turbo and a something for a clutch. I need some advice on what to do before I place my next order. The car came with a 7-bolt and I am switching over to a 6-bolt so at the bare minimum...

As the title states, will a SC61 compressor cover fit over a GT35r? I am planning to go the GT35r route and would like to have the HTA or GTX version but I'll save that upgrade for later. For now I plan on buying the Genuine Garrett CHRA and picking up the turbine housing that fits my current...

babyviper submitted a new DSM Profile :AWD spyderRead more about this vehicle here...

I've seen a lot of ball-bearing turbos on Ebay replicating Garrett ball bearing turbo. When the first GT35r replica came out we soon realized it was only a journal bearing turbo. I pretty much stopped paying attention to Chinese made turbo until I saw these start showing up on the market. They...

So I brought a DSM a couple months ago and I got the temp registration. By the time I got the car running and to my house the registration had expired. Does anyone know of a good Maryland inspection station that does safety inspection. PM me with the info, thanks

So i have a pretty massive oil leak and its probably because its bent. I had to pry the oil pan off from the rtv holding on so tight. I would like t get a new pan but I can only find brand new OEM, straight from the dealer. Does anyone know if an aftermarket company sell one like Dorman or Spectra?

I am looking to install braided steel from tank to rail later on this week and when I was putting inmy trans last night, I noticed that there isn't much room where the stock feed line runs. Does anyone have issues running -8AN feed with a -6AN return through that hole?

I am sure many of you have installed transmissions from the ground and I am wondering what everyone has been doing. I have always owned FWD DSMs and I recently picked up an AWD spyder a few weeks ago and had to do a clutch install. I usually set the trans on my chest and chuck in in there. For...

If some one needs help with a dsm in the South Jersey Area:rocks: pm me :thumb: :talon:

:talon:Hello every one......... I built a car for someone and would like to take it to a good tuning shop. Im from N.J The fighter is a 95 tsi awd 6bolt with ss valves, B.C 272 cams, stock intake manifold mls gasket, arp head studs, wiseco pistons, manley rods, arp main studs ,remove bs...

Hey, Guys I found a video of a Electric talon its a 1g . This would be cool to see if it could be push to run some numbers LOL. :talon: YouTube - Home Made Electric Car [url]

Well i built my girl freind a 97 gts spyder converted auto to manual . My problem is the car will not boost past 9-10 psi !!. mods are crower 264-272 14b turbo 7cm, willy 255 pump , afpr 43.5 psi.ngk non protruding 7es plugs 3' down piple 3' exhaust test piple on, hallman bc. jeff (dsm chips)...

Well i built my girl freind a 97 gts spyder converted auto to manual . My problem is the car will not boost past 9-10 psi !! :sosad:. mods are crower 264-272 14b turbo 7cm, willy 255 pump , afpr 43.5 psi.ngk non protruding 7es plugs 3' down piple 3' exhaust test piple on, hallman bc. jeff (dsm...

Well i built my girl freind a 97 gts spyder converted auto to manual . My problem is the car will not boost past 9-10 psi !!:cry:. mods are crower 264-272 14b turbo 7cm, willy 255 pump , afpr 43.5 psi.ngk non protruding 7es plugs 3' down piple 3' exhaust test piple on, hallman bc. jeff (dsm...

I'm not here to be a hater of bash the company but I think there new website just sucks. There's no other explanation for it. unless I am completely missing something here the website before was real nice. You could find fuel kits rod-piston combos now when you type in the make and model of your...

You can see my setup in my profile but just to break it down I have a sc61 with a Turbonetics cast manifold. I have a Tial 38mm wastegate off runner number 1 and I had the boost set to 20lbs. Even with the boost set to 20lbs it still crept to 26lb in 3rd gear. I then figured "what the hell" lets...

So, I'm trying to finish up the car and I am having problems when I boost the car past 6000rpm. i get smoke out the exhaust when i boost past 6000rpm and I don't think it is engine related. I have checked the plugs after boosting and they have no oil deposits on them. i would switch to getting...

I always wondered what shops meant by stating a head was not streetable. For example slowboy's stage 6 head and jacksonautomachine.com stage 4 CNC head. Just to give you an example to what I call streetable, I drive a 98 talon with a journal bearing sc61, no cat, kaaz lsd that locks up all the...