does anyone ever replaced a evo3 16g housing from kinugawa down firing housing? They claim that it will fit, but need to know of anyone ever tried it. Any fabrication need to do with the internal wastegate?
been reading a lot but I'm still lost with this. first trouble I got into- downloaded ecuflash 1.44 and the 96531706 rom to my desktop but every time I try to open it, it will not load the ROM to the ecuflash. Am I missing something? can someone please go through step by step for me? thanks for...
is it possible to install freeze plug while the engine in the engine bay? one of the rear freeze plug came off. I don't feel like pulling the engine off. anybody tried this before?
Recently bought a punishment recirculated EWG O2 housing, now doesn't really align with my 3" downpipe. I'm currently on a market for downpipe and wondering if there's any other downpipe that would align with my setup? I know punishment racing downpipe fits, but is there any other ones?
Make's whistling or metal grinding sound when im driving it always comes out whenever im on vac around 15-17 inhg, it goes away when i rev or let go the gas or i get off the 15-17 vac.. It sounds like eeeeeng... Metal grinding or whistling?
can anyone here show me step by step how to setup my sd? I have mitsu style 4 bar map and iat with pig tail. I connected all the wiring but when I start the car, it runs fine then when I rev after i let go the gas pedal the rpm goes really low and running rich. I read the entire sd101 thing but...
can i use epoxy instead of welding a aluminum bung to aluminum pipe?
i need to finish my sd setup and getting it welded will cost me $75-$100 too much for just the bung. can epoxy handle it? would it work?
I search, but can't find any proper answer. I need diaghram and pictures where to grind it and wiring diaghram. I got a 96 sc2 alternator with 4 pins in it, I understand about not connecting the F pin. I can't find any oem pigtail on any junk yard, is there any other alternative and where can I...
Acl main bearings, which color goes to block and cradle? When I opened the boxe it Has yellow and clear plastic, I dont know which one goes to block or cradle?
can I used evo8 and evo9 pistons together? reason is that i bought a set of used evo8 piston, but 1 of them has cracked on the skirt. found an evo9 for cheap and wondering if I can used both together? also can i used evo8 rings with evo9?
I've been searching all day but can't find any answer. I purchased a evo8 piston and rods, now I need to know what else do I need to get or buy to get this piston/rods into my engine? i.e. rings ( what size and do i need the evo8 or 2g ), head gasket ( OEM? ), bearing ( what size and how many? )...
my ACT pressure plate fingers broke off, it even made a hole in my transmission. but my main concern is where the TOB located at, the finger made a deep scratches all the way around. I don't know if the transmission is still good I tried sanding it just to take the TOB out. you can see it in the...
Here we go, while driving one time, the clutch wont engage/disengage, so i readjusted the clutch through the pedal assembly according to vfaq, after a few hundred miles, i smell burnt clutch and just today while driving to work the clutch wont engage/didengage again, tried re adjusting the...
idle surge plus leaning. i test ohms 29.0 on all of them but when i unbolt it from tb to check if its moving. found out that when i turn the key on on position, it doe not move. does it means its shot?
Ok here's the situation, while the car is in neutral and try to rev it to 2000 rpm and try to keep it in 2000 rpm, the rpm drops down to 900 and up to 2000 rpm then down again, It's like I have a step 2 or anti lag but I don't. What would be causing this? I notice this when I was doing a seafoam...
2g creeps to lean from 14.7 to all the way lean on idle and while cruising. mods are E316g, walbro 190 rewire, -6an line from pump to fuel rail, aftermarket fuel filter. mods are up to date on my profile. i search here but couldn't find it.
ok i did BLT, replace fpr with afpr and im still...
2g creeps to lean from 14.7 to all the way lean on idle and wile cruising. mods are E316g, walbro 190 rewire, -6an line from pump to fuel rail, aftermarket fuel filter. mods are up to date on my profile. i search here but couldn't find it.
after replacing my battery, I started the car and while it's idling my wideband goes from 14.7 and creeps up to 22.4 and stays there until I rev it up then it creeps down again then after a minute it goes up again. what's going on?
and also my boost gauge goes up too. from 20 to 10.
I replace upper and lower control arm, and spindle hub assembly now the car sits low. could it be my shocks are blown? it looks like i need an alignment the top of the tire goes inward. it has a stock spring. can someone tell me whats going on?
I replace upper and lower control arm, and spindle hub assembly now the car sits low. could it be my shocks are blown? it looks like i need an alignment the top of the tire goes inward. it has a stock spring. can someone tell me whats going on?
been looking and searching but no luck. I just put the AC back together and can't find the harness that connect to the ac compressor, I don't know if the old owner cut it off. where's that harness start from so I know what area to look from.
my tob is going out, because when I barely press the the clutch it make the woosshh sounds and goes away when i press the clutch all the way in. My question is can I replace just the TOB, because the clutch is less than 20k i believed. I haven't taken out the transmission yet because i'm not...
would 1g thermostats housing and neck fit on 2g head, just bought a water gauge and dont want to drill on my thermostats housing or the neck, somebody told me just get the 1g thermostats housing and neck because there's an extra hole where i can tap my sensor for the water gauge.
Just like the title says, how to install ac on 2g. I've been searching but no luck, I bought the car with no ac but he gave me the parts to put it back if want to, its getting hot here in cali so time to put it back, the only thing i'm missing is the compressor, but before I purchase the...
i recently install my mtx-l wideband to front o2 housing and spliced the brown wire or tap it to 76 or 75 anyway, I'm drilling a hole and put a o2 bung on the down pipe, now my question is where and which wire do i tap in the ecu? i know that the brown wire for narrow and yellow for wide. I dont...
help on evoscan.. trying to log but it's not connecting to the ecu am i doing something wrong? I clicked openport 1.3x, dsm/3000gt/ecl.MUTovrOBDII. I have 97 gst with 99 flashable ecu. and evoscan v2.9
I just log for the first time using the mtx-l innovate wideband that came with it, now whats next? I have flashable ecu and getting 2.0 openport soon.
big evo 3 16g
blitz intake filter and metal intake
6an fuel line from tank to rail
mtx-l innovate wideband
just installed mtx-l innovate wideband and on cold start it idle between 14.4-14.7 which is good, while driving it goes to rich 11.2-13.4 and when I let the gas off or while shifting it goes to lean 24.4. anybody knows whats going on?
I'm still waiting for the tactrix cable, anyway since I'm installing my wideband today I'm going to swap my ecu to 98/99 flashable ecu, now the question is do I just plug and play and the yellow wire from mtx-l wideband connect to pin 76 for o2 front sensor, again its a 97 so i dont need to swap...
I just bought a MTX-L wideband, I kind of confuse about the wiring. first, red wire, connect to 12v source ( which one is it? ). second, white to headlight power (which one)? third are the yellow and brown wire, it says for data loggers and ecu, where do i connect that if i'm installing my ecu...
when I push the clutch in and leave it in for too long the car will stall. It rarely ever happens, but when it does I just let the clutch out a bit to start it back up. can anybody tell me whats wrong.
when I push the clutch in and leave it in for too long the car will stall. It rarely ever happens, but when it does I just let the clutch out a bit to start it back up. can anybody tell me whats wrong.
i have a 97 gst and an extra 98 flashable ecu, what else do I need to complete the set up. dsmlink is too expensive. so pls tell me all the tools and equipment i need.
i have 97 gst, 16g big evo3 turbo, 3" intercooler piping, 3" down pipe all the way to exhaust, now the question is do i need to upgrade my fuel injectors? i have walbro 255.
i have 97 gst, 16g big evo3 turbo, 3" intercooler piping, 3" down pipe all the way to exhaust, now the question is do i need to upgrade my fuel injectors? i have walbro 255.