Hey guys, about 2 years ago I was in the process of tuning my car. Went through all the basic ECMLink testing stuff making sure it was mechanically sound, no boost leaks etc.Had the car close loop tuned and was beginning on open loop, when one day it started running poorly out of nowhere and I...
1). Any boost, vac, or exhaust leaks?
Vacuum and exhaust good visibly good, tight and all new. I don't have a boost leak tester.2). Verified mechanical timing?
Yes3). Verified base timing?
Verified CAS but i cant get idling long enough to set ignition timing.4). Ignition system
COP or...
Hey guys. Pretty sure I got this right, but it was hard to tell on some low quality pictures from older posts.Feeding my PTE 6176 (or 20g if I run that) off the 91-94 OFH (oil filter housing)’QUESTION: is my 90 elbow to feed the turbo in the right plug hole? Looking for the filtered one...
Note: Always balance your full rotating assembly when modifying a turbo, even if each part is individually balanced. See Justin's post below for a video.Just thought I'd share with everyone my latest project.Had an old small 16g sitting around from my old car, so I thought I'd learn how to...
Basically I need to know if the front subframe is the same on fwd and awd 1st gens.Apologies if this has been asked before I attempted to search but only have my phone and trying to get to pick and pull. Thanks
I need a 1g awd front subframe as soon as possible. Willing to come to you.Need a few other things as well like passenger front axle.shoot me a txt 360 461 5146 Thanks!
My mods include, B16g, 650cc FIC, 3" GM MAFT (blo-thru), AFPR (stock psi), PLX wideband, SAFC, MMCD dataloggerSo before I installed the chip, I had maft base on 6 (thinking it was v1.3) But I have v2.01 so that would be for 490cc injectors. On top of this I had about -10-15% on the SAFC...
I just ordered a datalogging kit so I can tune my car. I figured id put my 650cc injectors back in at the same time.So would I put 0's across the board on the maft and use only safc to tune?Or should I put the injector scale at 650cc on the maft (rest 0's) and then use the safc?
So my 94 AWD tranny is in pretty bad shape (synchros), and I have a 90 FWD GST parts car with a much better transmission.Basically I was wondering if I'd be able to just swap over the whole gearset from the 1990 FWD tranny to the 1994 AWD tranny, rather than buying a whole new tranny.Thanks
When pulling my engine recently, the wires got yanked out of a connection for my PLX M300 Wideband.It's the one that's directly connected to the O2 sensor. Theres 5 wires, grey, yellow, red, white and black.Could someone look at their's please and tell me how they go back...
Whats currently done to my car:Engine/turbo: Stock head(rebuilt OEM w/timing 3k miles ago)
Cometic MLS headgasket
Stock Bottom end checked, polished, honed by machinist. New rings/bearings and waterpump...
If you were like me and many others, than your headlights looked a lot like this...Luckily, Turtle Wax has a new, easy to use, cheap solution! Turtle Headlight Lens Restorer. This was the $8 dollar kit, found at Walmart or any autopart store I'd assume. There was also a more...
CURRENT PROGRESS::Well, months ago I had piston slap, and begin tearing my motor apart.Block was toast due to deep gouges in #1 cylinder. But I did found out my car had Eagle H beams and JE pistons...unfortunately also toast :(Anyways, picked up a stock shortblock from Evil94Evo had it...
Before I start, please don't say it can't be done or you're wasting your time.My car is a 1994 Eclipse GSX. I bought the car about 4k miles ago, and this is my first time tearing into it.I've researched for hours about the process of removing our engines, and for
1. I don't want to...
Having no start issue. Im Not getting CEL when key is "on" or at "start," however, the boost gauge will go to "0."Things I've checked:
-Getting spark at all 4
-AFPR reads correct pressure
-Getting gas to rail, havent pulled injectors and checked tho
-Used starting fluid, didn't even try to...
Background infoJust before buying my 93 Eclipse GSX, there was 1,700 in engine work done includingMachining of Cylinder Head
Replace All Timing Components and Thermostat
Crank Seal and Drive BeltsParts:
Head gasket kit
intake and exhaust valves
Timing belt tensioner and roller...