SO i got a full dyno tune for my 2g and im running a fp3052 with all supporting mods and it made 355whp 314wtq on a mustang dyno at 24psi. he brought it up to 33psi but there was no increase in power due to no timing so he tuned it on 24psi with peak 11 degrees of timing he said maybe im having...
I need to know what kit to buy I'm going to be running 93 pump with a fp3052 and I'm looking to push it hard. Will my wb255 be enough? My 880s? Thanks guys
Ok so I have been preparing my 2g for import face off at New England drag way and got it dynotuned on a mustang dyno and only made 318 corrected hp 333 uncorrected hp whatever that means and around 300tq on a downfireing 20g running 30psi I feel like I should of made more can anyone chime in? He...
Ok so I just got dynotuned and my excedy stage 2 is slipping at 298hp 310tq won't get past that ### the damn clutch slips I didn't resurface my flywheel maybe that's it? But what is weird is there's no clutch smell the car still pulls hard just not what it should. It's pulling like it has 375hp...
So I bought a parts car with Ross pistons and the lower end was machined .30 over there mounted on 1g big rods but I want to order nice rods what rods would I need to order just stock size manleys? Thanks guys
So I picked up my 90 Tsi for 500 dollars all stock 127k on it and I need to rebuild the motor due to lower compression, rings are junk. I just need to know everything I'm going to need to replace I know I need piston rings rear main seal all new gaskits head studs main bearings timing components...
after i installed my pte880s my cars air fuel ratio was all out of whack i got it kind of in line if someone could just check this idle log and tell me if its safe thanks guys
i need to know if everythings correct when i go wot it studders i hope this log uploads if not let me know how to upload one thanks guysheres a wot 2nd gear pull its real laggy then breaks free probably around 5500 i need advice can someone dumb down the ecmlink website lol
so after my 7 bolt sucked in more water then the atlantic ocean had to offer i swapped in a 6 bolt but i want to shoot for bigger and better things now i feel i have the supporting mods to go bigger then before. my 7 bolt put down 292whp 288tq on 19psi droppping to 16 through redline on 93...
Ok so I have my 2g just 6 bolt swapped it it runs and drives fine but wen I go to pull boost Afr drops down to 10 and lags for a couple seconds then pulls pretty good it's usually around 3 3500 rpms where should I be adjusting I also have 280 cams w valve springs and retainers the problem only...
so i took out my front 02 sensor and put my widebang sensor in its place i wired it into number 76 pin and the wideband reads but my dsmlink throws the check engine due to 02 sensor but besides the fact wen im 30 percent throttle it reads in the 14s but as soon as any more then 30 percent the...
So I live in mass and am going to be driving to California soon ### I don't want to part with my baby lol I recently sucked in water and lets just Say my 7 bolt let go lol so I swapped in a jdm 6 bolt did the timing belt with all oem timing components put a mls head gaskit arp head studs bc280...
so i blew my 7 bolt in my 95 tsi and im putting my 6 bolt in i was tuned on ecmlink, when i swap the settings to 6 bolt will that tune carry over to the 6 bolt block? should i retune it or is it safe to drive? its a jdm motor and i put bc titanium valve springs and retainers and 280 cams in what...
So im ordering the combo from extreme psi but what hg thickness do i order and what size bore on the studs its a stock 6 bolt im putting 280 cams with titanium valve springs and bc retainers i dont kno if that makes a difference. I need to know asap thanks guys.
alrite so i was driving on the hwy and i put it in neutral to stop and guess what hahaha it wouldnt go back into gear. if the cars off i can put it in gear and turn it on and it will drive just cant switch gears.so i think the clutch is still good.i had it towed home and looked at by a mechanic...
So i bought my 95 tsi a few weeks ago and it has launch control. The kid told me the ecu is chipped so does that mean its chipped for link? Is there any other ecu mod for launch control? Let me know thanks guys
So i was lookong into an auto 95 gsx for my girl as a daily someone macked her car but i test drove one and is it normal when i put it in drive the car diddnt roll itself? It only got going when revved to like 2k? Also felt real sluggish acceleration wise he said it because the awd is harder to...
i have my 95 tsi with the original motor at 135000.It runs mint no complaints but i want more power out of it.As of now it has a 16g ,650s ,wb255 ,injen intake ,full 3in exhaust ,chipped ecu for launch control and tuned on safc.i have cams but everyone keeps telling me the motors not worth it so...
so my cars heat barely works i have to leave it on full blast to get any heat lol. i usually drive all city but yesterday i did a few pulls on the hwy and the hear was blareing out like it normally should.i get back in the city to normal driving and nothing again. people have told me i might...
So i picked up a blue 95 tsi a week ago and tonight i just picked up another blue 95 tsi haha i just figured i would post it because i thought it was funny im beginning to hoard these cars i picked up my 94 tsi for 2gs my 95 tsi for 2500 and this exact same 95 for 500 it has a bad motor but i...
so i bought this 95 tsi awd and it runs like a dream and mechanically sound.it has 135k on it but it must have been rediculously maintained.it has a 16g,wb255,650cc inj tuned on safc it had a make shift intercooler setup but just bought a ssac fmic.its running 21psi and drops to 20psi but pulls...
just bought a 95 tsi and the dash lights dont work and the heat and air dosent blow.what do yous think fuses? its too dark outside haha thanks guysit also has a mean idle surge haha any input
95 talon tsi awd, 135,xxx miles,car is in decent shape runs and drives good, its got a stage 3 racing clutch, 16g, wb255, short shifter, light weight flywheel, 650cc fuel injectors chipped, Apexi S.A.F.C, cold air intake. manual boost control, exaust temp and boost gauge, turbo timer, 3 inch...
im about to give up on my talon a few months ago i pulled the motor to drill out the broken bolts for the intermediate shaft bracket and put a spacer in the spot where the ac bracket was suposto be.And guess what....wait for it.....they broke again so im pissed off lol....i just want to come to...
When i drive it sounds and feels like my driveshaft is slamming around under my elbow.Is there sompthing suppose to be there preventing it from doing this? Let me know asap thanks guys and one more question will bad motor mount make the car lose power? thanks again.
this is my budget. ive read the upgrade paths but want more imput just let me know and im looking for 300-350hp.my motors a 99 7 bolt with 20k original miles and tranny to go with it so its healthy lol.so just hit me up asap thanks guys...
i have a turbo xs mbc and sometimes it holds 13lbs but sometimes it will just pull right to 20lbs but it falls on its face its annoying?Is there anyway to fix this? Whats a good fuel system upgrade and cost for it because im getting a bigger turbo soon?
I just got done pulling out the motor and drilling out the halfshaft bracket bolts put everything back together made sure a hundred times the vac lines are connected right and still only 7 8 lbs im used to 14 even installed a mbc still nothing. Turbos got no play at all im stumped. Ive tried 2...