This was used about 3 times just for the sake of passing emissions. So, very low mileage.Please see attached picturesMake offersMy text number is 4o4-5o9-7418Thank you

Have a bunch of fabrication parts for sale.Exhaust manifold flanges, 3" v-bands, 1 1/4" stainless steel elbows, O2 bungs, -10/-6 AN aluminum bungs, 12" 1.5" sch10 pipe and a bunch of fabrication scrap metal. Please see picturesSee my other auction for the 3" hi-flo cat..Make offers on...

Made this a while back and it never got used so brand new. You can grind the welds and polish it, if necessary. Comes with a coupler on one side. This was originally designed to work with the factory radiator. Please see picturesPrice is $45 shippedMy text number is 4o4-5o9-7418Thank you

Have three 38mm tial knockoff wastegates. These are the good quality ones and are brand new with the tial logo on them.Please see attached pictures.Price is $60 shipped eachMy text number is 4o4-5o9-7418Thank you

Have a factory 14b/16g oil feedline with the banjo bolts.Also, have a 46" long -4 AN oil feedline.Make offers on anythingMy text number is 4o4-5o9-7418Thank you

Have a holset wh1c that needs a rebuild and two t3 factory housings. Please see attached pictures.The nice looking t3 housing came with an hx35 that I purchased from jusmix on here.Make offers on anythingMy text number is 4o4-5o9-7418Thank you

Pretty good condition crankshaft, could probably use a polish though.Can provide more pics upon request.Price $150 plus shipping

Please see pictures ask any questions and make offers on anything interested. Thank you.Text 404-509-7418

Have a lot of miscellaneous engine parts for 6 bolt turbo engine.1g rods with 2g pistons, arp headstuds and main studs, rear mail seal cover, main caps clearanced for a stroker, 2 squirters and factory bolts.Please see pictures. Make offers on anything interested.

Have for sale eagle h-beam rods with weiseco 2.3 liter .040 over pistons.Price is $50 for each combo. Only have 3 available.

For sale is a very low mile FP 8cm exhaust housing for 14b/16g/hta68 turbos. No broken bolts, comes with a clamp for cheap.Price is $125 plus shipping

Treadstone/turbonetics T3 exhaust manifold $150 plus shipping38 mm gatePlease text 404-509-7418

Very minimal use time, practically brand new. This was the updated version. Price $325 shipped. You get to save 50 bux over buying a new one.Please text 404-509-74One8

Have a lot of fab tools and materials. Jigs, purge blocks, flanges ,heat sinks, elbows, pipe...etc.See pictures, message me for other things if your looking for something.Please text 404-509-74One8

Please see pictures. Condition is good no damage or major scoring on the journals.Price $150 plus shipping and feesPlease text 404-509-74One8

Ceramic coated, 38mm gate. Price $190 shippedPlease text 4zero4-5zero9-7418

New turbo built by forum member jusmx141. $550 comes with factory t3 twin-scroll housing.If interested please text 4zero4-5zero9-7418Here is an original add from jusmx141:Price: $600.00Parts Condition: Brand NewNew Holset 7-blade 54/78mm HX35 turbocharger. This is a relatively...

Need to get rid of my old parts car, currently it's sitting in my brother's backyard and I need to move it.Only has about 160k miles on chassis. Comes with 3g eclipse wheels, 4 bolt rear end with axles, clutch pedal assembly rebuilt by Shepard. Has a lot of miscellaneous parts still on it...

Was asked to make a 5" aluminum exhaust downpipe and dump tube for a drag rb25 240 sxY-pipe for a 2100hp full street r35 with full interior and a/c . Lol

Hey there, trying to get out of the DSM game to free up some space and move onto a different project.Really just hoping to find some local people first before making individual for sale adds.I have two identical black/silver AWD '91 Eagle Talons. One is a parts car that still has a 4 bolt...

Need some suggestions on this.Haven't done anything to my talon since last November, other than just driving it. Which is good i guess, but naturally the car has developt a couple issues.One of them is it started to idle at about 12.5 afr but only after driving it for a while. The cruise afr...

Hey guys, long story short i used a ghetto shop to install new tires on my rx7 and they didn't replace the valve stems. Had a tire go flat and had to limp to the nearest place that actually ended up being a discount tire. They didn't want to reinstall the tire back because of the damage.I...

Just installed a VCE and removed t-case and driveshaft. Took the car for a test drive, it drove fine until i floored it and instead of roasting front tires it just free revs the motor. Feels just like the clutch is slipping. ( the clutch is good)What can cause that?I assume something broke...

Not sure if this has already been done before, but i thought it would be really cool to try make a true 3" exhaust. Here is what it looks like.. About 98% done, just need to remove the cat and replace it with the flex section instead. Also, might have to re-do the charge pipe so it doesn't...

Tried to boost leak test my car yesterday and noticed a huge boost leak coming from my 1g bov, as soon as, it sees positive pressure.Haven't found much information on this issue, surprisingly, except for this video:http://m.youtube.com/watch?v=du8fl1p8FVoThat seems to be the same...

Installed some coils with their own ignitors and now since there is no more factory transistor, the tach isn't working.Any way to get the tach working w/o having to go with aftermarket tach?

I have 3 front cases, all have what looks like straight cut oil pump gears. I would like to find out if these cases were actually designed for straight cut gears.The only markings that i see on them are "DOH" letters between main seal and oil pump gear, and numbers "500520" written next to...

The car just started doing this a few weeks ago. It drives and works just fine other than that, so this issue never became a priority but is still annoying. lolBasically, when the car starts reaching a full operating temperature the idle rpm's start going back and forth a little bit and...

Trying to figure out what could have caused this. All bearings look good except the thrust bearing. The oil clearance was .0015"-.0017" measured with a bore gauge and double check with plastigauge. The engine spun freely with one hand and without extensions. Thrust bearing journal on the...

I'm rewiring all of my interior gauges/devices and want to get an advice on what is the best switched 12v source to hook up to the fuse block.The fuse block has 6 (30Amp) channels, most of the accessories are going to be bulbs and switches. But there is going to be probably more than 8 of...

I'm rewiring all of my interior gauges/devices and want to get an advice on what is the best switched 12v source to hook up to the fuse block.The fuse block has 6 (30Amp) channels, most of the accessories are going to be bulbs and switches. But there is going to be probably more than 8 of...

Started doing this today and it's driving me nuts lolI have been raising boost slowly on the 14b from spring pressure, got up to 14psi and everything felt and looked great. Than today, raised boost again up to 15.5 psi and logged almost 34 lbs/min with AFR's in the mid-low 11's, then on the...

Trying to figure out what these wires are in here, the yellow and grey ones in the pictureThank you

I need to replace the copper line on my mechanical oil pressure gauge. I found a place that sells the line for $20 Braided Pressure Gauge Line Kit - Speedway Motors, America's Oldest Speed ShopCould someone tell me what sort of fittings would i need to use to hook it up to the gauge and oil...

I'm running a factory PCV system with a see-through fuel filter between valve cover and turbo intake pipe. I ran it this way for a while without any issues, until now. I'm 30 miles into an engine break in and just noticed there are some kind of resin looking pieces inside that filter...

Trying to figure out if this is responsible for the leaking oil pan on my brothers car. I hooked up an oil gauge today and the oil pressure is good. So then, i tried to unhook the breather tube on the valve cover while idling and it seems like it's pushing some air from there. When the engine...

I have a long driveway to back out of with a 2.3l and a 14b, the reverse gear feels like it's on steroids and makes the whole powerplant shake every time i press on the clutch and don't rev match.It's kind of annoying, are there any tricks to tone that down a bit?Thank you

My brothers car has a stage 4 pressure plate and clutch on it. The clutch grabs right off the floor, which i don't mind at all and actually prefer it like that.However, the only concern i have is when the front wheels are off the ground (with the t-case removed) and the car running, when...

Trying to figure out where this leak is coming from. Here are a couple of picks:Now, i understand that some exhaust manifold studs could leak sometimes but i'm just not seeing it. The one on the far right does look a little wet but it does not look like it's leaking around the stud...

Hi,i need to replace all four of my turbo bolts with different ones. I would prefer not to use heli-coil if i can, so i can't use OEM thread and pitch bolts.My plan is to find some good hardened bolts that i could re-thread into the turbo housing.Has anyone dealt with this before...

Hi,is anyone familiar with this kind of module? Trying to figure out the wiring on this thing..It uses a regular 5 pin bosch relayThis is what i have been able to figure out so far:Red - 12v main power Blue - fan Orange - fan or switch ?? Small Black - thermosensor Black...

Hi,is anyone familiar with this kind of module? Trying to figure out the wiring on this thing..It uses a regular 5 pin bosch relayThis is what i have been able to figure out so far:Red - 12v main power Blue - fan Orange - fan or switch ?? Small Black - thermosensor Black...

Hi,i have heard it is possible to change out rod and main bearings from underneath the car. I would like to get some feedback on doing that, hopefully, from someone that has actually done it.I already have pulled the oil pan and was wondering if there anything else i have to take off...

Hi,i'm trying to hook up a 90 oil cooler on my '91. I already have -AN lines from an aftermarket oil cooler. Can anyone help me with what kind of an adapter i need to make this work?It is going to be just like the one in the picture at the end of the line, except it needs to go into...

Hi,i was doing a leak down test on my fresh engine. For the most part everything seemed fine, the readings i got were all between 10-13% which is not bad for a new engine.However, the very first time i tried testing cylinder #3, i got air escaping out of cylinder #4. Tried to do the...

Can someone give me some tips/suggestions on cleaning out the cylinder head, please?My main concern is the exhaust runners. I poured some gasoline in them to check for leaks and now the carbon build up is flaking off. I'm worried it could damage the exhaust propellers.What would be the...

Was getting ready to drop the head on the block when my dumb ass decided to lay it down on two blocks of wood. I guess, i forgot that it had valves sticking out as it was already put together by a local shop.Anyways, a moment or so later i heard a slight clinging sound. Immediately...

Is it OK to take it apart for cleaning? Any tips or hints? I don't feel like breaking it or anything so just wanted to double checkThank you

I keep getting about 0.0005"-0.001" of endplay runout.Tried to re-torque all the mains except the thrust bearing cap, then torqued the center cap to 10lbs, pryed on the crank back and forth, turned it over and did the same thing. Then i torqued it to 20lbs and repeated the same process...

I just had to do this and thought i would post up a How ToEven if you have a machine shop doing all the work for you, double checking their work is your responsibility!I went to a reputable machine shop in my area that has done at least a couple of real high hp DSM's. I brought them my...