Hi,I am in the process of completing my setup. You can see the setup in my profile. What's not listed is turbo (scm61 or agp RS60T), exhaust manifold (DNP or SBR ported cast manifold), DSM Link, injectors (850 or 950) and intake manifold (????).I need to know what's out there for 2g's...

Hi,I was trying to install my dejon tool 2.5" upper intercooler piping with GM MAF sensor and tial bov. But looking at the picture, you see that I have hood clearance problems. Has anyone else ran into this problem with the same or simular setup? What did you do to make it fit under the...

Hi,I was bored this morning. So I thought why not do a comparison of the O2 housings I have. Test animal #1: EVO 3 O2 housing unported Test animal #2: nsindustries tubular O2 housing (ebay)The tests were done in a good manner with an accurate caliper and one of the best electronic...

Hi,I was wondering, if you can do the 1g cas mod without having it delivering the crank and cam signal. The reason why I ask is because I have a fairly new crank sensor. I was thinking to use the 1g cas for the cam signal and leave the yellow wire from the 1g cas unused. And use the 2g crank...

Hi,I have a hard time deciding which one to get. My goals for this year, is to get myself into low 12sec (12.2) and around 400-450whp. But I am still running stock engine, transmission and axles. So, I can't run to much boost. Say max about 20 street with pump gas, 25 track with race gas. I...

Hi,I swapped my 2g cylinder head with a 1g. I am almost done. But if I am correct I have to use the 1g lower radiator hose and the 2g upper one, right? Well, my 2g lower hose fits without any problems. So, here is the dilemma. I have to replace these hoses, because they are old and worn. Can...

Hi,I am changing my old setup for a new one. I was running a FP Big T28 and I wasn't satisfied at all. For now I am still running my stock 2g block with 1G head. But I want to upgrade to something "bigger and better". I am rebuilding a 4g64 block with eagle rods and wiseco pistons. My...

Hi,I am looking at a turbo kit with the T3 super 60 turbo. What kind of turbo is this? With what can you compare this? They have it listed as a T3 Garrett/Turbonetics Turbocharger 60 trim T3 Turbonetics compressor housing 3" inlet 2" outlet, .48 stage 1 Turbine housing, perfect for...

Hi,These are members that scammed me and others. ******************* I am filing a small claim against all of them. When the purchase is made through the internet use, you can file the small claim in your county. The filing fee is $60 per claim for my county (olmsted, mn). All the cost...

Hi,I would like to create this thread for everyone that is thinking or doing a 7 bolt 4G64 engine with the 4G63 head swap.The questions is to list all the parts you needed to complete the swap. If possible with part #, price where to get it. And to list the extra steps we need to make...

Hi,I am doing a 1G head on a 2G block for my 95 GSX. I have 2 1G water pipes and both don't have the connection where the 2G pipe connects to the oil cooler coolant line. How did you fix this eror and do you have pictures available? Are there any other things that I have to watch out for...

Hi,My car is a 95 eclipse GSX. I recently installed the HKS cams (264 in, 272 ex). I also swapped my throttle body with a 1G NT and installed greddy profec B spec 2 boost controller. These are the latest upgrades I made with my car. I finally finished the installs and tried to run the car...

Hi,I am sticking 264 in and 272 ex cams into my 2G stock head for the last track event of the year. I just want to run it 1 more time before the winter transformation to the rebuild 1G head. Just to make sure, can I ran the car with stock head internals and without adjustable camgears with...

Hi,My car is a 95 eclipse gsx. I have the 30-2801 AEM c2di module. After everything was connected, I ran the car with the adapter plug and everything ran fine. I installed the module and try to run again. It didn't. I checked all the connection. They are good. Checked for 12v and ground...

Hi,We all know that the best way to go is to swap a 6 bolt, but what about the new EVO VIII engine? The internals are rated a lot higher then any 2G. If I am correct they are rated up towards 600 bhp. Is there someone trying to accomplish this swap? If so, what are the procedures and parts...

Hi,I have problems with my boost levels. When I run, my pressure will go up to 17 psi and drop to 14 psi. I am worried to run higher boost levels, because of these spikes. Why are they occurring and what can I do to eliminate them? I am still running a mbc, but thinking to upgrade to a...

Hi,This is to the ones running race gas often or daily? I am probably going to run race gas on daily basis. But I want to know what kind you are running, does it harm your O2 sensor and for the ones in MN, where can I get a whole drum? Thanks,Sven

Hi,My car is a 95 eclipse GSX with the following modifications: - FP big T28 with 17PSI actuator - Greddy 24R FMIC + UICP + BOV - Ported EVO III exhaust manifold + O2 housing - Apex'I GT downpipe + catback + SAFC - FIC 550cc injectors - walbro 255 lph HP fuel pump - AEM fuel rail +...

Hi,I am rebuilding a 1g head (91), but the cams are bad that came wit the head. Can I use my cams (95) with this head? Thanks for the info!Sven

Hi,Does anyone have experience with this turbo, GT35R? If so, do you like it or not. Did you buy it as a turbo kit or single? From who would you recommend to purchase this turbo(kit)? What are the boost levels for street and strip? I found a nice turbo kit from AGP for $2500. It comes with...

Hi,For everyone running faster then 11.99 with a 2G. Do you guys (and girls) have a roll cage? If so, which one would you recommend. Are there different sizes for the bars? Thanks for the info.Sincerely,Sven

Hi,I have a 1G head and I want it installed on my 2G. What do I need to modify? What are the do's and don'ts? I am also going to purchase a 6 bolt. After I converted the 1G to my 2G can I reinstall it on a 1G block without any problems? If someone can sent me a link of pictures that would...

Hi,I am searching for a equal lenght tubular exhaust manifold for a 20G turbo with the waste gate mounted to it. The waste gate is preferable the Tail 38mm. I don't want those $200 quick break shit! I looked into DN performance one, but they use a 40mm waste gate.Thanks for the info.Sven

Hi,Does anyone have a fuel cell in their 2gen? How did you install it? Are there any problems you ran into? If possible, can you sent me some pictures?Thanks,Sven

Hi,I have a 95 eclipse GSX. I replaced my suspension with Tein basic coilovers and SPC front and rear camber kits. The car is lowered to the Tein basic specs 1.4" in front and rear 1". The distance between the wheel center and fender edge should be 13.5". I can't check that because my car is...

Hi,I have a 95 eclipse GSX. I am replacing the rear swaybar with a suspension technique swaybar. It should clear most of the 3" exhaust, but not mine! I have issues with the clearance between my apex'I GT catback and the swaybar. Has anyone else run into this problem? And what did you do to...

Hi,I have a 95 GSX with a big T28 turbo upgrade and some major modifications. I am thinking to get a rebuild / ported cylinder head. who has one, do you like it and would you requiment it? What to get and what not? What to watch out for? And so on... I know there are a few companies like...

Hi,Within the next month or 2, I am upgrading my complete suspension? But reading the forums lately, I am getting confused about what to get. First I was thinking to get KYB AGX with skunk2 coilovers, camber correction kits (probably from specialty products), probably lower the car to max...

Hi,Where can I find nice body kits? I prefer websites that are respectable. Also, I prefer the quality to be better, than the price cheaper! I like so far the Hen style Buddy club 2 with the wings west commando style wing and possible Aerogear BW2 style or X-1 style fenders.Thanks...

Hi,I started to hear a knocking sound (like gears not matching) where my 3" downpipe meets my transfer case. The noise is not coming from inside the transfer case. And I noticed that my downpipe is rubbing against the transfer case a little bit. When you shake the downpipe or move the...

Hi,My setup includes a FP Big T28 (I was running 20PSI of boost) and the supporting parts. I have an autometer lunar mechanical oil pressure gauge. My question is what max oil pressure will I have at which RPM's? I read a forum in which they stated not to go over 60 PSI. My car will have...

Hi,I just bought the autometer lunar EGT gauge. I am wondering where do I need to install the probe. Autometer says "For turbo engines to install it 1-2 inches from the turbo exhaust outlet." But I have been reading about people putting it in runner #1. So, where does it actually go now...

Hi,I am running a FP big T28 and wondering what the best quarter mile time is. What is the highest amount of boost you can run with the stock side mount intercooler?Thanks,Sven

Hi,I just received my BOV, but all the instructions are in Japanese. There is also no schematic to hook up the hoses. So, I need help with hooking up the hoses and how to tune it at the right setting. I will be running 15-16 psi on the street and 19-20 on track, if this might help...

Fuel pump rewire kit available at DSMotorsport.1) First thing I did was, disconnecting the battery. 2) Then, position the new relay were you want it. I placed it at the bottom of the fuel tank cover plate, under the back seat. I secured it to one of the bolts. 3) Run the new power feed...

Hi,I am installing my apex'I GT catback to my apex'I GT downpipe. I also replaced my stock O2 sensor housing with a EVO III housing. I have problems lining them up. It seems that my downpipe is in a different angle to match with the flange of the catback. With twisting around, I was able to...

Hi,I have a 95 GSX. I bought the Upper intercooler kit from GReddy. Can I use the universal BOV type S without modifying anything or do I need to buy the kit for my car?Thanks for the help.Sven

Hi,My car is a 95 gsx. I am looking for some specific items. Body kit: buddy club 2 Wing: wings west v-line custom wing w/o light or erebuni GTR style wing #159 Do you know where I can find these items? And how much they cost? Is there someone with these mod? Can I see some...

Hi I have a big problem. I have a 95 gsx. And saturday is a new race event. My crank pulley is broken. The outer part is slipping on the inner part. I am trying to take the pulley off, but I can't put any force on the inner side to hold it still and to break the nut loose (that connects to the...

Hi I want to know which ones you prefer and why. So please help me out.ThanksSven

Hi, I have a 95 GSX. And I need a new clutch. My 2 choices are MB1-HDSS and MB1-HDR6. Which one would you prefer and why? Is there a big difference in engaging them? Because I found some information telling me that the HDR6 is harsh to engage. What do you think? Thanks your the info...

Hi, I have a '95 gsx. And I am searching for pictures of 2g with tenzo ZT6 or 5Ziegen fireball rims. If someone has one or knows a website were I can match my car with those rims, please contact me. Thank you.