I have a 1998 eagle talon and I was getting the P0105 code and I did the vaccuum lines and I put in an AEM fuel pump. The car will run for a while and then stall and it stalls when you put the car in gear. There is a strong fuel smell and now the car won't start. Any suggestions as far as what...
I have a 1998 Eagle Talon TSi and I needed a three hose sending unit. I was wondering if anyone knew of any way to get around using the three hose unit? All I keep finding is two hose units and I am not sure if I can use a two hose unit and modify it? I am unable to find a new unit and I cannot...
I have read numerous threads on this CEL and none are any help. I am getting this CEL and I have tested the map sensor and was getting the correct reading. I put the vacuum pump on the sensor and those readings were correct as well. Any ideas as to what may be causing my car to stall and this...
I did a 6 bolt swap on a Gen 2 car with a Gen 2 head. I have replaced the crank angle sensor with the wire harness and I changed the ignition coils, replaced the spark plugs with NGK plugs, replaced the wires, the coolant temp sensor. My car starts with no problem and it runs for about 5...
I am looking to get bigger valves for my Talon 1mm over and I was trying to get opinions in which valves are the best to purchase. I was looking at Brian Crower valves and a few others and I am not sure which stainless steel valves to buy.
I purchased the black hall effect CAS and it does not match the plug that I had for my last CAS. Does anyone know where I can get a new harness for the hall effect, I have been looking and cannot find it. I have a 1998 Eagle TSI. Thanks for any help.
I am trying to install my Greddy Ultimate EManage and am having issues with the wiring. I am not sure where to connect all of the wires. I have the ecu harness out but I have to connect the rest of the wires. I have attached a picture and was wondering if anyone knew what it was a pic of. Thank You.
I have a Greddy Ultimate E-Manage and I wanted to know if I also needed an Apexi boost controller. I did have a boost controller prior to getting my E-Manage and someone took it out of my vehicle and I am not sure if my E-Manage if enough. Thanks for any help.
I have been trying to adjust my clutch and have been having issues. I tried to get the friction point at 2 1/2 inches and was not able to get it above 1 inch. I saw black gunk in the fluid and was not able to push in the slave cylinder and thought it was because I needed to replace the slave...
I was looking at a FP 88 turbo and I was trying to see if anyone had any insight into this turbo. If this is not a good choice any other ideas would be greatly appreciated.
I have an ACT2600 and ACT flywheel. I have been trying to get the clutch adjusted properly and I cannot get the friction point at 2 1/2 inches. I have tried to adjust the rod and the pedal and have had no success. I did see debris in the fluid and am not sure if I have to replace the slave...
Could anyone help me decide which electronic boost controller is better for me to purchase? I was looking at the Apexi and possibly the 420-a904 and 420-x905. Although, I am open to other suggestions. If there are certain specs that I should be looking for please let me know and I will...
Does anyone know what this piece is that is missing from my ECU? I think that this may be the reason that a cel came on with the p0100 code. I have also attached a few pics that will hopefully be able to show whether or not there may be any other issues with the ECU.Thanks in advance for the help.
I have a 1998 Eagle Talon TSI that I did a swap on. CEL with code p0100 came on and I took out the ECU to see if it has to be rewired. I do not know if I need a different ECU or if I have to hook up my E-Manage. I am not sure if I need the metal ECU because I have a black one with a plastic...
I finally got my car started and it ran for about 1 minute and then shut off. The engine light came on and the code that came up was 90340, camshaft position sensor. I have a crank angle sensor on my vehicle. I do not know if I have to hook up my e-manage system or if I have to adjust the...
I was getting spark and then I did not have spark in #1 and #4. I changed the coil pack and there is still no spark. I have recently had the electronic boost controller removed from the car as well and I do not know if that would have something to do with it. I know that the timing is...
I rotated my block 25 times and I put in the CAS. When I try to start the car it seems that it is going to start, but instead it backfires. I do not know if that means that it jumped time, or if there is something else that could have gone wrong. I checked the timing again and it seems that...
I broke my gen 2 tbrottle body elbow and I was wondering if anyone knew if I could use a gen 1 elbow until I upgrade the intake manifold and throttle body. Thanks
I have and gen 1 block in a gen 2 car with a gen 2 head. I lost the oil feed line for the turbo and I am trying to figure out what line I have to purchase. I removed the balance shaft. I do not know if the line should be to the oil filter housing or to the head. THANKS.
I am trying to hook up my gen 2 oil cooler on my 1998 Talon TSI with a gen 1 block and gen 2 head. The bracket is from a gen 1 non- turbo and there is too much room. I do not know jf I have the wrong bracket or the wrong cooler or if there is another piece that I may need in order to complete...
I have a 1998 Talon, with a 92 engine block and a gen 2 head. I was wondering if I would be able to use a 98 stock oil cooler off of the old block. 2nd, does anyone have a diagram on how to hook it up. It has been so long I want to make sure I do it properly. Any help is appreciated. Thanks. WTF
I have a stroker kit in my 1998 Talon TSI with a 6 bolt motor and a gen 2 head. Everytime I try to put it in time the crankshaft gear keeps moving 3 degrees down from the marking when I try to put the Kevlar belt on. Is there another way that I should fbe trying to get it in time? Not quite...
I have been having an issue with my Eagle Talon. I have a 98 Eagle Talon with a gen 2 head and a 6 bolt block. I have been unable to get it to start. I did get it started on time for a few minutes and when I shut the car off I could not get it to turn over again. I thought I might have a...
:banghead::banghead:
I have a 6 bolt block in a gen 2 car with a 98 head. I put the vehicle in TDC and I lined up the CAS sensor, I got the car to start for a few seconds and then it shut off and it would not start again. I believe that I wired the sensor properly, although I am not too sure...
I have a 6 bolt turbo Eagle Talon. I was replacing the timing belt and had turned the crankshaft numerous times and the engine turned normally. After I tried to start the vehicle and it would not turn over. I thought it was not timed properly and therefore I tried to turn the crankshaft and I...
Do I need an oil cooler for my turbo? Currently I have it hooked up without an oil cooler. I am almost done with my Talon and I want to make sure I have it hooked up correctly. Thanks.
I rebuilt the motor in my 1999 Talon and put a gen 1 motor in with a gen 2 head. I finally got everything done and got the car started. When I shut off the car and checked the oil it was a milky consistency. I believe that I may be mixing antifreeze and oil. I am thinking that the mixing may be...
I have a 2G car and a 1G engine and a 2G head. There was a crankshaft sensor on the engine and I needed to have the CAS. I purchased a new CAS sensor and a wire harness to hook it up. The wire harness that I got has three connectors. One of the connectors fits the CAS at the head. Can...
I have a gen 1 block and a gen 2 head in my 99 talon. I bought a 92-94 cas and harness. I am trying to install the harness and I cannot find what it connects to. I have been looking online and it seems that one plug is the cam sensor plug and the other plug is the crank sensor plug. If someone...
Installing a Greddy Blow off Valve on my 1998 Eagle Talon TSI and I was trying to see if anyone has a diagram of how everything should be installed. Help would be greatly appreciated. Thanks.
Does anyone know where I would be able to get a water pump pipe for my 1G turbo Talon TSI? I can't find it in the salvage yards and only saw one on EBay and it is for a 2G and I am not sure that it will fit. Thanks.
I was wondering if anyone had any idea of where I could go to get diagrams (pictures) of a Big 16G being installed. I am having problems finding where to buy the oil supply line and water pipe assembly and I am trying to find the banjo bolts for the install. I have a 2G head and a 1G block that...
Which flywheel is better to purchase? A ACT flywheel or Fidanza. I have heard good things about both and i figure I might as well get whichever is better since I am putting in so much work to my Talon. Anyone with experience with either, your info would be greatly appreciated.