I will take the ridicule. However, I am posting this. I got scammed by Steve Kinsinger. Even after I was warned by Ludacris. However, I am leaving this here for others. Do not be fooled by his buddy buddy demeanor. It is a con. Do not listen to his stories of the good ole days of...
The reason I am doing this write-up is because there is literally no information on this throttle body's wiring. It comes with no diagram of any sort. Now before you say, "well it tells you the car it is meant to bolt into". Do not waste your time. This is not a bolt in affair even for the...
Ok so I am starting this threat to document the full install and fabrication of a Willwood pedal set along with a brake master and clutch master. I will document the entire installation. I am doing this because I looked high and low and could not find information on it being done. I know Luda...
I have decided to change my engine management setup. I am selling my Link ecu. Not ecm link but LINK. It will come with two expansion harnesses original box. This a
EVOLink (IV-VIII) - #EVO8+
I am asking 1,200.
Again this is a new unit.
I have an HKS EVC6. I bought it a while back. I've decided to go another route. I have the original box and instructions. I've seen them new from 5-700. I'll take 400 or better offer.I also have an aem wide band. I have the original box. $100
AEM Electronics Wideband Air/Fuel UEGO Gauge...
I would like to sell my ecmlink ECU. I need to upgrade. It will come with the cable. It was just sent in for a checkup and had an updated chip put in. I have the paperwork. I'd like to get $650 shipped.
It has come to my attention that I have the wrong half-shaft bracket. I need a manual 95-96 bracket. Please let me know what you have. Also please make sure that it is what I need.
So i just finished my build. I got the car idling. I noticed the timing at times will stay at 7.0 degrees. Then at other times it jumps to 18-19 degrees then falls below 0. I have a black top with a kiggley crank sensor. I read there are guys that have this set up and doing just fine. I...
So I have a 6 bolt swap. I have a blacktop so the signal is inverted. I also swapped the wires at the ecm. When I replaced the cas, i put all of the marks on point. So here is my question. If I set TDC to factory #1 cylinder. Yet because I swapped wires, is it still #1? Which call do I...
Listen guys, I have asked msd, who was no help, how to install the msd dis2 in a dsm. I have seen the diagrams and they do not account for the transistor. I see the wire that goes from the transistor to the coil plug, which is black with blue stripe. Also the black wire that goes to the little...
I am trying to run an in line vacuum check valve between my distribution block and brake booster. i would like to find one with -08 ends or something that i can weld them on. Is there any suggestions to my problem.:confused:
Hello guy and ladys. I am loking for a place to purchase all of the rubber stripping for my 2gb talon. Car is getting painted and I don't want to put the old stuff back on.. I would also like to know where to purchase the p:Dlastic pins for mounting them. Any help would be appreciated.:D
Hey guys some of you may know this build, others may not. But I moving this build here so it Can be found. I value opinions very much. I have put a lot of time and money into this build. Her name is grace, Here Is the link to the blog. For now on I will be posting progress...
:hellyeah:My BeastOk so I love cars, but I love games and computers aswell. So I had a beast built.
Intel i7 extreme processor i7-980x
rampage 3 extreme edition mb
dual galaxy gtx470 grafics cards
3 raid wdre4 hd 500gb
1 baracuda 500
12gb ddr3 corsair extreme ed memory...
Ok, here goes....after getting ripped off by a local shop I have decided to build my own car, and thus far it has been a success. What I don't know I Google, and I have paid close attention to detail, and tried to build a dsm, not only I could be proud of but we all could. Some thing you may...
Ok, I have just gotten my hands on a 2g talon awd, tsi I supose, it has a blown head gasket.....but thatws fine, I have a lot u goodies on my 2g eclipse, but the talon is awd, the body on the talon is ruff but everything is there, I have been quoted upwards to 4000 to swap the awd stuff on my...
I did not know where to put this, but any who, I am looking for an engine dampner kit, my friend has one on his evo 8, and I cannot find on for my 2g, does any one know where I can find one.
I just built a strocker motor using a 2.4 crank, I wont go through all of the mods to many, but we tried to start it and it was backfiring through the intake. The intake was hot and the exhaust was cold, so we noticed that the cams were 180 off, so then we tried to start it again and it is...