The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Rix Racing

Search results for query: *

  1. kenuwine4g63

    AEM My Rpm gauge off[RESOLVED]

    Im running the aem ems v1 with a 12 tooth disk. My factory rpm gauge is reading off by maybe 1800-2k rpm. I tapped the signal at the ecu from the crankshaft sensor(blue/white) but the car wouldnt start. obviously the signal bypassed and went to the cluster. I disconnected the wire to the ecu pin...
  2. kenuwine4g63

    AEM AEM V1 trigger disk settings

    Im using a yoshifab 24 tooth trigger wheel in my green top cas. Car is a built 7 bolt with the ecmlink adapter for the 2ga to 1g cas adapter. I used the Triggerdisk.com settings to set it up in the AEM ems V1. Im still using the stock coils as well so its still wastespark not sequential. I have...
  3. kenuwine4g63

    EVOscan Linear ipw patch

    Whats going on guys. Does anyone have the linear ipw(injector pulse width) patch. Not the minimum ipw patch to lower the minimum amount of ipw. The one with the correction without the latency. I have one of them but it wont show the graph. The one tephra made has a bug in it from the site where...
  4. kenuwine4g63

    General 1G with 2g MAFand LUCAS 550S injectors

    I thought this balanced everything out..my car is extremely hard to drive when out of boost. I'm also running a fmic and a tdo5h 20g....the maf is not hacked. There is also no boost leaks the car bogs at idle and at cruise and part throttle. It sounds like a skip with some backfire..I can't...
  5. kenuwine4g63

    lean or rich?

    I just finished my setup on my 1g. Tdo5h 20g 550s 2g maf and fmic....the car has bogs in it when out of boost normal driving. As soon as I press the gas pedal the car bogs but picks up slowly. when boost arrives the car goes and drives normal anything out of boost and the car hesitates..if...
  6. kenuwine4g63

    ecu swaps

    Will a 91 ecu work in a 92....both turbo
  7. kenuwine4g63

    Weird check engine light

    Ok guys my check engine light is doing the wildest things i can imagine..When i first bought the car there was no cel, but the car had a blown intake manifold gasket. I replaced the gasket the car runs a million times better. Now the cel would come on while at cruise on the highway, i could give...
  8. kenuwine4g63

    Balance shaft bearing in oil pan (I Believe)

    I bought my eagle talon earlier this year. It had a rattling noise goin on like something bouncing around and a very loud wooooming sound. So 8k miles later its still there and i made my conclusion that its the balance shaft bearing. No if i re-time the timing and phase the shaft correctly would...
  9. kenuwine4g63

    Mechanical timing off at cam gears?

    Ok, I know there is plenty of threads on this but for futher notice and clarity I need some further opinions. I lined up my cam gears today to see if they lined up, they did! But, it looks like my exhaust cam gear is slightly off just by a hair. Tell me what you guys think. The exhaust cam gear...
  10. kenuwine4g63

    Loud winding noise on my 1g after 3k rpm

    Ok guys i have to update my profile i bought a 92 eagle talon tsi, it has 96k miles. But there is one problem, when im driving and i get to 3k rpm it makes a loud winding noise all the way till i stop accelerating. Even when i come off the gas and let the car rpms come back down you can still...
  11. kenuwine4g63

    Everything rebuilt no compression

    Ok guys i really do not understand what is going on. I have rebuilt the Head, the piston rings has been changed and cylinders honed. My car will not start due to compression. I have fuel and spark, and still nothing. Now the dowel pins face up on the cam gears, the timing marks on the cam gears...
  12. kenuwine4g63

    stuck piston

    My piston is stuck or jammed. Changing my rod bearings and piston rings. I put the ring compressor on my num 3 piston and started to put it in the cylinder. Got it to the head and got stuck. It look like its jammed and i cannot get that bad boy out. Any help would be great.
  13. kenuwine4g63

    rod bearings and piston rings

    Ok, I want to know how good are the ACL rod bearings. Im going to be replacing my piston rings soon and rod bearings. Everything stock size no bore or nothing. Who makes a pretty good set of piston rings that i could buy. I seen NPR but what are my other choices. I've been looking to but just...
  14. kenuwine4g63

    concerned about testing coil pack

    Ok, im having problems testing my coil pack. 2g dsm. Mainly with my primary resistance. It wont hold a steady reading. It'll go from 0.25 then to 0.00 and stay there. I do know that it suppose to be from 0.77 to 0.95. Im not sure if i should have the car switched to the on position or what. My...
  15. kenuwine4g63

    Bad starter?? Do not really know

    Ok guys i've been at this car for about 4-5 months. My starter does this-When i put my battery in(bad cell, but had it charged just to start the car, And no, with a good battery it didnt change anything) and started to start the car. It started turning over real slow then it'll start turning...
  16. kenuwine4g63

    Bad battery cell with no start

    I just found out i have a bad cell in my battery. My car does not want to start for nothing, i have fuel spark and compression. Could this bad cell cause this. The mpi RELAY has been replaced, but is there a MPI FUSE?? I've heard there is one by the positive cable on the battery and i can not...
  17. kenuwine4g63

    Wont start for nothing..Everything replaced

    Jesus!!! This car will not start to save humanity. It is a 95 talon with the original 7bolt block. The head has been rebuilt no leaks no nothing. Im using a 1g green top cas(jnz tuning-harness) head gasket is fresh. I have replaced the MPI fuse, engine coolant sensor, fuel pump, injector...
  18. kenuwine4g63

    quick 1g cas question

    OK. i have a 1g cas on my 95 dsm. I didnt switch the pins at the ecu, i switched the two blue wires at the igniter plug(Red/blue, blue/green) to invert the signal. Do i still have to do the pins at the ecu for the injectors?
  19. kenuwine4g63

    reused felpro HG

    Alright quick question, car has not started for a long time due to head replacement. I bought a felpro headgasket, i have had it torqued down 3 times. The first time the car jumped time and bent valves. I didnt drive it this was on a rev when i put the car back together(didnt tighten the...
  20. kenuwine4g63

    2G no start after head change?

    Ok guy i searched and searched and cannot find/figure out the problem. I came to the conclusion that i have no spark..AT ALL..I just put another head on the car due to my last one bending valves. I have compression but no spark. I have a volt tester that messures all resistance and voltage..When...
  21. kenuwine4g63

    Tell me what u think..No compression??

    I think my valves are done. They dont seat against the head..Dosnt this sound like no compression..http://www.youtube.com/watch?v=tu4hkil71tU
  22. kenuwine4g63

    cracked valve guide

    Ok, now i have a cracked valve guide where the valve broke off in cylinder one. Its cracked on the side like a straight line. What could be the dangers of driving with it like that. If i have to replace it then im going to get rid of the car.
  23. kenuwine4g63

    Its over....motor locked??

    :cry::cry::cry:Ok just got finished putting some antifreeze and (Royal purple)purple ice into my radiator. I cranked the car and it turns over, it cranks, i rev it to about 4.5k to 5k and screetch there it went. Oil on the ground and metal shavings:notgood: I was so happy after a whole month...
  24. kenuwine4g63

    battery negative wire

    Ok guys i have a black and yellow wire from the negative side of my battery that is attatched to nothing. I just replaced the head and dont remember this wire being bolted down to anything. The motor does not turn over the fuel pump only comes on. Could this cable cause my car not to run??
  25. kenuwine4g63

    camshafts wont turn

    Ok...in need of some good help. I just replaced the head on my car, so i have it on and i started to do the timing belt job. I have the belt on snug/tight and proper but i cannot get the camshafts to turn. I honestly made another mistake and was turning the crankshaft and "slip" there it went...
  26. kenuwine4g63

    Valve keepers

    Ok guys my arms, hands and back is killing me:cry:..I've been installing the springs, valves, retainers and keepers in my other head. I've been using the needle nose pliers to install the keepers. Today im officially done with that im in pain..what other DIY options are out there to install thes...
  27. kenuwine4g63

    ok..97+cas

    I have a 97 cas that i wan to put on a 95 head. Ive searched and searched and the only thing i come up with is for the 1g cas with the 4 prongs as the 97-99 has only 3 prongs. How would i go about wiring these up.Does anyone know??:confused: C'mon guys
  28. kenuwine4g63

    I would love to see this at theatres(the full version)

    http://www.youtube.com/watch?v=5FOrU-bTaJwThis was a pretty good mini movie i thought you mitsu heads would enjoy:thumb:
  29. kenuwine4g63

    auto tensioner arm held by a bolt???

    Im a noob when it comes to timing belt changing on a dsm.:D Its not hard as long as your marks line up and your auto tensioner isnt leaking, But i have a question and im a lil concerned about this. Theres a bolt thats against my tensioner arm(i guess applying pressure to keep the pulley against...
  30. kenuwine4g63

    Broken fuel rail bolts

    Hey guts, i just broke two of my fuel rail bolts to the head. Whats the bolt size and pattern. I know it has to be m??x1.25, but "m" what, and how long. Another thing what will be the best thing to get the bolt out of my head, both are broken flush against the head. Could a drill out do the job...
  31. kenuwine4g63

    no more chrome

    Ok guys i need to know how to get chrome off of the 5 spoke gst wheels. Im not really a fan of chrome on a DSM so I want to paint mine but they are chrome. What could i use to get the chrome off because its pretty thick. I was thinking the paint stripper wheel would work but i have no idea, does...
  32. kenuwine4g63

    boost fluctuating

    Alright guys did some searching and nothing specific. I just purchased a Hallman ES mbc, im runing 15psi on a 16g. My boost keeps fluctuating like it will go to 15 then back to 12 then back to 15 very rapidly threw 2nd all the way out to 5th gear. Has this happened to anyone and if so please...
  33. kenuwine4g63

    liscense plate slang

    Ok guys im going to get my metal liscense plate this thursday and i want a custom one. Im very undecided of what i want, I just want to see some creativity from you guys as what i should consider getting. It has to be car related. Heres a couple im thinking aboutnonvtec e316g 24psi4u...
  34. kenuwine4g63

    wastegate arm stopper

    Simple question where could i get another washer that goes after the wastegate arm to stop it from coming off or what could i use in place of it. Ive tried alot of things and no help!! Is there a vendor i could order them from??I need some help guys my wastegate arm keeps coming off..
  35. kenuwine4g63

    16g mbc turbo XS HPBC slow spool

    I have a question. I just got finished doing a boost leak test and got all of them taken care of. My evo3 16g hits full boost at 3800 rpm on 10psi. Now with my actuator arm, will it cause a problem if it was not twisted to where it would slide onto the flapper. I have it where i have to pull it...
  36. kenuwine4g63

    Boost leak test failed

    ok guys, i just made a boost leak tester today with a 2in male cap and a 2in pvc female pipe. Drilled my hole threw the cap put the valve stem in sealed it with pipe glue(cement). Then i went to autozone and bout the spectre coupler that comes with the two clamps. I put it on my car hooked up...
  37. kenuwine4g63

    gauge cluster Fuse keeps on blowing

    Ok guys my gauge cluster fuse keeps blowing...and i know the gauge cluster fuse is in company with the tailights. Ive done the 2gb eclipse conversion on a 95 tsi talon so i had to adjust the lighting in the rear. The fuse is a 15 fuse, so i went and bought some 20 fuse and it keeps blowing them...
  38. kenuwine4g63

    16g spools like gt42r

    Whats up guys. My 16g spools super late on 15psi. In 2nd gear it creeps to 15psi and by the time it gets there its time to shift, so i have no power. I also noticed that it howls. I do know that my down pipe is not all the way on. Could that leak cause my turbo to spool super slow and howl like...
  39. kenuwine4g63

    Boost no steady????

    OK guys...EVO 3 16g, 2.5 inch exhaust fuel pump rewire. OK, my mbc is set to the lowest possible wastegate pressure(10psi)..now it will start to fluctuate on wide open pulls it wont stay consistant. It'll go from 10 to 13 back to 10 and 13 and so on. If i turn it up it does the same thing just...
  40. kenuwine4g63

    Throttle body wont close

    OK guys. Ive had this problem for a while. My throttle does not want to close. When i drive the car and come to a complete stop my idle goes higher and higher. So after doing some searching and testing simple enough(I thought) my TB is not closing. After a drive it would be idling at about...
  41. kenuwine4g63

    Resolved 2g TSi EPROM ECU - 2g GSX Eclipse EPROM ECU

    What's the difference between a 95 auto EPROM ECU and a 95 5spd EPROM ECU?Will the tranny difference be the difference in the ECU? When i swap them things go wacko? The original ECU (in the car now) looks ok, but the other one looks better than the original one.As soon as i swap the car...
  42. kenuwine4g63

    Car revs slow

    Whats up guys. I just recently bought a 95 tsi talon with 2gb eclipse conversion and i cannot figure out the problem with the motor. For starters it sounds like its cammed at idle and when i rev it the tach goes up so slow and when it reaches 5k it dosnt want to move like it gets stuck. It idles...
  43. kenuwine4g63

    Cas blocked off

    Ok, i just bought a new dsm for $1200. It only needed a turbo, but before installing everything i realized it didnt have a cam angle sensor. Where the cas goes its blocked off with some kind of plug. Is it like this on the 7 bolts. Its a 95 Talon tsi with a 2gb eclipse gst conversion. And...
  44. kenuwine4g63

    I hate to ask-honda question

    I didnt want to post this but im stumped :banghead:and the guys at hondaclub.com(i guess) dont know anything but bodykits and so on:notgood:..Im a DSM man but my mother just bought my brother a civic and the speedometer is not working. If anybody knows anything about speedsensors on Hondas...
  45. kenuwine4g63

    Where can i get a data logger

    Wussup guys. I was wondering where could i get a data logger or pocket logger. All of the loggers i've seen have been for the 1g dsms and the 2g dsms no one makes. Where could i buy one. I have a 97 gst with a 90 6bolt swap. thanks
  46. kenuwine4g63

    bad mbc???

  47. kenuwine4g63

    something funny

  48. kenuwine4g63

    wut u think, im curious

  49. kenuwine4g63

    bad mbc???

    I think my mbc is bad. I try to set it, but it gives me different boost pressure in each gear. Im trying to set to 14-15psi. I'll end up with 9 in 1st, 17-19 in 2nd, 11 in 3rd and so on...need help should i chuck it:hmm: Ohh yea the bottom nipple goes to the actuator and the side nipple goes to...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top