The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Rix Racing

Search results for query: *

  1. obd issue/question

    Tried that getting nothing from the obd ..that's why I am asking what wires to tap into for the obd ...I am assuming all the wires have been cut already for other accessories.
  2. obd issue/question

    not sure what to do or where to start..1g talon buddy has whats called a chump car , 1g talon with every race option ..stock engine ecu.full roll cage , fuel cell ,wideband ,deleted head lights wired in led lights , switches to turn every thing on the car on including ignition ,fuel, wipers the...
  3. 1g weird issue happening

    post for a buddy 1g talon hx35 , 255 pump , s90 tb ,1000 id high z injectors , cob ,fiav del ,dsmlink v3 ,,sd omni 4bar map ,fprissue is :s90 ,1000 id ,cob ,fiav del, new fpr were just installed now the car will start and idle only when omni 4bar map , vac line isnt on (has its own source)...
  4. SLEEP THIS 10 sec fwd tame the beast

    Hit the track yesterday ....Bad news car shut off leaving 2nd gear (still using the n/t trans)...Ran 15.99 Will be ripping into it tomorrow to see what happened..hoping its mpi related , when i was trying to start it back up while coasting down the track it was cranking , couldn't hear the...
  5. help. my car dies all of a sudden..

    this just happend to my 94 4g63 last night at the track shifted out of 2nd and car died out couldnt get it to start again (within 10 mins) - ended up towing it home
  6. 2g talon engine problems

    picked up a new talon thats turning into a project ..Bought it with no keys at an auction , very clean all new parts , oil looked good ....Got a key cut go to start it , everything turns but the timing belt .. So i ripped it all down find out the timing belt was all ate up as well as the...
  7. SLEEP THIS 10 sec fwd tame the beast

    Finally finished the beast , after some set backs , some other minor issues ..Got it tuned and ready to hit the track tomorrow ,..Videos and numbers will follow soon after!!
  8. ecmlink boost control solenoid

    figured it out pin 105 for power and knock sensor for switched ground ,...hopfully that is the problem
  9. ecmlink boost control solenoid

    the fire ring was on right ,But the bcs is not turning on ..How do i wire it to the ecu ..pin 105 and ??
  10. ecmlink boost control solenoid

    maybe the firing ring is backwards ?? not letting it fully close .. will double check that to.i do believe that is the problem after looking at some pics
  11. ecmlink boost control solenoid

    Was having my car tuned today , for wot pull was only able to get to 5.5 (not bars) ...Going to be logging wgduty tomorrow , as well as checking to make sure the bcs is turning on ..but it might not be , because of wiring it was a n/t car then converted into a turbo car ..So the wiring may not...
  12. Last problem to fix , clutch noise

    when the clutch is pressed there is no noise , when the clutch is released its grinding ..I have changed the master the slave , and the tob 3 times with the oem , i have seen jacks video ,..Is it not adjusted properly?.., when i adjust it some its like there is no clutch cant get into gear ..How...
  13. Ecm tunning what am i missing or doing wrong

    I will try that tomorrow , Lc1 was calibrated awhile ago then removed until i finished my build couple days ago ,i will recalibrate it tomorrow ..Load scale in direct access was at 114% before i started , and reading in the 1g v3 dsml link no maf sd tuning pdf , it says Load scale tab: Leave...
  14. Ecm tunning what am i missing or doing wrong

    hx35 , rc 1600 cc injectors , 255 pump with rewire , SD set up , wideband1st log is still in open loop then goes into closed loop and starts going weird , 2nd log i adjusted the tps since the idle went to 2k once it hit closed loop ..What am i missing , what am i not doing right , what am i...
  15. Quick bov question

    anyone on the boost control solenoid
  16. 4 bar map sensor , housing replacement??

    it sheared the nipple off i will take pics while i am messing with it
  17. 4 bar map sensor , housing replacement??

    that is where i had just bought it from lol , i am sure there is a way to open the casing and put a new casing with the vac nipple , i will be grabbing some from the junkyard to play with ...If the omni 4 bar map sensors are that brittle , cant see myself buying another ..May go with another...
  18. 4 bar map sensor , housing replacement??

    well some how my new 4 bar map sensor , the vac nipple broke off ..My question is there a way to open the housing up and replace the housing with another one ..I have a 1 bar gm map sensor kicking around some where would the housing work .If it will how to i pull it apart ?
  19. wireing problem/ wideband help

    Well installed map sensor , to the erg pins ...I also had my wideband hooked up to the erg pin at the ecu ...Went to swap the brown wide band wire to pin 4 (white)-( oxygen sensor input) ...But i followed the white wire out of the car and its connected to the cas :confused: ..Only thing left...
  20. Quick bov question

    Now hooking up the ecmlinks boost control solenoid , How will i hook the hoses up ? external wg ..
  21. Quick bov question

    I will be using the ecmlinks boost control solenoid , haven't hooked it up yet
  22. Quick bov question

    Almost done the build and come to the last line the bov ...My intake was a n/a had a nipple tapped awhile ago for the bov line , i am now using that nipple for the sd map sensor ...Where else is a good source to run the bov line to ..Also just to make sure for the external wg ,.I run the lower...
  23. 2G Auto transmission issues

    not sure if you have the od button (overdrive ) push it to off then try it ..
  24. 1g hx35 intercooler pipe routing

    time has come to do the bottom ic pipe routing , any one have pics of how you did it ??
  25. SLEEP THIS 10 sec fwd tame the beast

    got the exhaust and wg dump tube done today , just have to finish off the ic piping and weld the bung for iat ....Then its time to get a tune and e85 hopefullyBig thanks to Alt custom exhaust
  26. 1G Couple questions

    thanks i will try heating the housing some , and grinding down an allen key a bit ... Any one else for the rest of the questions
  27. 1G Couple questions

    Finishing off my hx35 install and deleting a couple things1st: How or what do i use to block off the , turbo coolant feed line on the t-stat housing it is B: in the pic2nd: went to pull the plug / block off plug (off the bottom of the ofh) for the oil feed.. its in there so tight it...
  28. 1g talon high to low idel / vac when put in gear

    Found the problem dis morning ..kept going over the logs noticed the air flow was low , swaped in a new maf and air filter , fixed the problem ...Thanks
  29. 1g talon high to low idel / vac when put in gear

    it isnt the egr fixed that i have dsmlink so i tossed that in adjusted the tps , timing is spot onNow when i start it , it gradually drops rpms and dies out (with in a 1 min) ..And still drops vac when put in gear down to about 4-5 i tested for boost leaks none at tb, injectors , ic etc I...
  30. 1g talon high to low idel / vac when put in gear

    just did a blt , couldnt find any , but did notice the egr has no lines going to it , can that be the problem hereAnd where do i find the 2 hoses to hook up to the egr ??
  31. 1g talon high to low idel / vac when put in gear

    will be doing the blt tomorrow , any one else have any ideas The weird thing is it only happens when putting it in gear
  32. 1g talon high to low idel / vac when put in gear

    not my car in my profile, its my brothers car 1991 awd auto , turbo - with manual ecu and 450cc injectors ..We did try swaping in the auto ecu still had the same problemProblem is when started (warm or cold start) idels around 1500 vac is about 9-10..when i put it in gear ( drive , reverse)...
  33. Do I have a blown head gasket?

    put a new t-stat in , and test your old one ..Boil some water drop the tstat in see if it opens ..Try a different rad cap also maybe yours is shot I just finished doing a head gasket on my brothers (coolant was flowing out like a water fountain ) -checked the coolant no oil , checked the oil no...
  34. sd install wires wires

    just didn't know what way to wire it in , to much reading had me running in circles
  35. sd install wires wires

    got it figured out
  36. sd install wires wires

    maybe i am reading to much, going in circles.. have egr delete and just uninstalled gm 3" maf and translatordoing a gm iat , 4 bar map installIat tap in at maf connector green and orange stipe (pin 8) ,.Green and black stripe pin 64 bar map is where i am going round and round port a 4...
  37. SLEEP THIS 10 sec fwd tame the beast

    Quick update Installed the rc 1600cc injectors , will be wiring up sd tomorrow ...Still trying to find someone to fab a vband to dsm exhaust 02 housing ,..Once all that is done get her tuned , And track time !!!
  38. water fountain of coolant

    Car: 1g talon tsi auto quick break down , been having serious coolant problems with this one ..Had to replace one after another ..Top rad hose, both coolant lines to turbo , bottom rad hose , another coolant line to turbo , .. Today it blew a coolant hose going into the ofh .Temp was just a tad...
  39. Coolant in oil

    Is the car running hot ? pull the lower timing cover, it maybe from leaking water pump.
  40. need some advice what to look for

    checked the coils they are fine on the other side , still have to replace them of course ..Well got the head off today .... The head gasket was still good WOW keeping this strong head gasket ,still looks brand new lol...But of course the timing slipped , bad , bent valves Almost all of them...
  41. need some advice what to look for

    Started ripping into it today , Wow the spark plug wires melted in the holes had to smash all the plastic off to pull a plug , just to do a compression check ..No compression ..Ripping of the head to check the damage , head will be off in the morning ..I cant believe the whole car didn't burn...
  42. need some advice what to look for

    the head gasket did not go already tossed coolant in double checked the oil , That seems fine ..i have spare heads if it is the problem ...The story was the guy was drunk started it for heat woke up and car wouldn't start , rad blew ..Only 113,000 kms also
  43. need some advice what to look for

    brother picked up a 1990 awd turbo talon .... Rad was blown whole top , was gone..Car was over heated plastic over spark plugs and timing cover was melted .... Tomorrow i will be ripping into it the wires behind the vc are fine all wires to cas are fine ..The car will not start , i will be...
  44. SLEEP THIS 10 sec fwd tame the beast

    Ordered SD and Boost Control Solenoid from ecm last night , Wow by the time i woke up it was already shipped love it :thumb: Started gutting the awd , will be attempting a full wire tuck , removing absThe last 2 pics does any one have any idea what that is ???
  45. SLEEP THIS 10 sec fwd tame the beast

    After talking to some people , i will be ordering sd and Boost Control Solenoid On a side note i ordered the t3/t4 to dsm flange 02 housing ..Went to put it on and of course the flange is not for the hx35 , so i have to get one cnc'd and custom fabbed ..In the end $300-$350 02 housing lmao it...
  46. SLEEP THIS 10 sec fwd tame the beast

    After some thinking and talking with others , I decided it was time to pick up an awd car , tossed up a post for an awd with blown engine since funds are tight , 2 days later someone posted an awd with #4 piston spun barring , engine and driveline out ..Decided to take the gamble , engine came...
  47. SLEEP THIS 10 sec fwd tame the beast

    Sorry didn't see your post , no Full break in is done 750-1000 km's per clutch
  48. 16g boost issue

    It ended up being wg shit the bed , and bad mbc ..Thanks guys :thumb:
  49. SLEEP THIS 10 sec fwd tame the beast

    Quick pic update , mounted it for a test fit ..Pulled it off had the hx35 ported , picked up the 38mm wg ,..Just waiting on the 5 bolt to dsm exhaust flange in the mail ..Waiting on warm weather to put in the new valve cover gasket
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top