hey guyscar 2.3 stroked 98 gsxi have problem with warm startups after my PTE 1000cc instali have Dialed in injectors good cause my fuel trims are in the -+5 areaso when the car is warm i have to give it a lil throttle on startup and for like 1 sec i see black smoke from my...

hey guysmy car 98 gsx with 2.3 stroked engineso yeah i started tuning with ecuflash 2 days ago i instaled my PTE 1000cc injectors dialed new injectors in pretty good because my fuel trims low are almost 0but my Aem uego shows 16.8 - 17.5 on idle ??in WOT its showing good...

hey guysso i got my 2.0 open port cable today and i went to the garage instal my PTE 1000cc and flash my ecu with ceddy modsmy engine is 2.3 stroked btwi changed injectors scaling to 940and latency i did " select all than add to data and i put .450 "my table looks like this...

hey guysi found a good thread on 3si forum about evoscanHow to: Tune Scaling and Latency tables for larger fuel injectors using ECUFlashi started reading this and post #2 and #3 says that evoscan values for fuel trims are incorrect ?is this true ?? Does someone heard about it...

Hey guysi build 2.3 stroke engine and im thinking of putting it in my car this week.But i know stroke engines likes lower timming.Im looking for someone in chicago that knows how to tune with evoscani will evan pay you for a basic tune just the timming .ill drive by your...

Hey guys.Im building a 2.3 stroker right now and i need some torque specs to do it right.I need torque specs for main cap , remember that im using 4g64 (2.4) crank, are the torque specs the same what 4g63 crank is using ?Im not sure here thats why im asking you guysThe crank was...

Heyy all :DIm about to buy a block to do my rebuild (winter project ) and i dont know what block should i get ? i mean what year of the block ? with the thrust bearnings ? or split thrust bearings ? To dont get the crank walk issue later.I want to build 7bolt block .so guys what year of...

hey guysi have a questionim building my block ( winter project ) and i need to buy new used crank.and i dont know which crank to get evo 8 / stock 7bolti was looking for stock 7bolt crank but then i found some evo 8 cranksok so now my guestionwhat is the good and bad...

hey guysi need your helpim doing short block build and i have to know if i can put 1g 6bolt rods with some Forged pistons like Wiseco , JE or Ross Pistons IN 2g 7bolt block ?? is this passible ??no compresion change ?is the 6bolt rods are the same lengh as manley h beam or...

ok im changing my piston rings in my 98gsx and i dont know which way to put them on top ? thats the ring #1which way on the top ??please helplook on pic

hey guysi have one quick questioni just did valve job and put new piston rings in my engineand i want to know the Torque spec for the rod cups bearnings?it is 98 gsx 7bolt engineand i will be putting back my old bearnings !thank youany one ??i dont know because im putting...

hey guyssDoes someone here have cometic MLS or felpro MLS or mits oem mls head gasket for sale ??i live in chicago and i need a new gasket for saturdayor does someone knows where i can get one in chicago ?? what shop does sell them ?thank you so much

hey guys :Di have two questions.whitch head gasket is better ??felpro MLS or cometic head gasket ???and i have cometic head gasket right now in the car and im going to pull up the head on monday to do the valve job, and im just wondering if i can reuse my cometic head gasket ...

hey guys i just get the vag 409.1 cable and it works with evoscan . and i log my car :(when i drive like 6/10 pulls i get 35 count of knock and the car is like not moving / its bogingbut sometimes i get 0 count of knock and the car is pulling hardwhen the car is cold ill always get 35...

hey guysi have a guestionwhy my car sometime feels like the turbo has a lot of shaft play ?? the turbo is new and it doesnt has any shaft play at all .its like when i drive in 2nd gear at 2.500 rpm and than go WOT the turbo will boost fine but the car wont have power, like it will statrs...

Hey guysmy friends eclipse 96 gst is done :/ the crank went badd :/quick question will the 98 gsx crank will be okay with 96 block ?? i readed somwhere that 96 block and crank is a lil differend what 97-99 block with crankthxx guys for infoo

hey guys i have a quick question about oil in transmisionim about to buy Red Line oil to my 98 gsx manual transmisionand im not sure which one to buy :/3 quarts of MT-90 ?? or 2 quarts of MT-90 and mix it with 1 quart of MTLwhat do u guys think ??my transmision has...

Hey guys I would like to know what are the symptoms of timing belt jumped?What is happening to the car if its jumped? How to check if it jumped?BTW my car lost like 40% of power and I need to check my timing belt if its ok .thanks a lot guys

i have a problem with my 98 GSX . So my car is running rich , i can say that becasue i smell gas from my exhaust and i get low gas millage and the car just dont pull hard like it used to :/when i look on my scan tool and when the engine is cold it says "(closed)open loop"and when car is...

i have quick question to you guys so im just wonering what Compression Ratio pistoms should i use for my 7bolt build ????9.0:1 ???? or 8.3:1 ????is it looks good ?? < Wiseco Pistons and Eagle Rods >it is gonna be my 350/400hp DDthx a lot for help :D

i have a free 1g NT TB and idk if its worth to install it on my 2g gsx ?? does the 1g TB really add much or any performance ????? what do u guys think ?????thx a lot for help and advice :thumb:

Hi guys . I was just wondering if this is normal that i have oil in my cam angle sensor ??? i have 98 gsx and the 2g CAS i dont see any o-ring in there :/ it should be ??heres a pics<a href="http://s459.photobucket.com/albums/qq320/dawid4444/?action=view&current=IMG00209.jpg"...

Heyy guys , yesterday i got check engine light so i went to my garage with my laptop and check engine light ,after that i check my intake temperature and it was TOO HIGH :/ it was 127.4F(53C) !!! anything above 84F(28.8C) or below 34F (1.1C) we will lose one degree of timing , so i know im...

It is based on this articlehttp://www.dsmtuners.com/forums/articles-electrical-wiring/329825-foglights-without-headlights.htmlbut when you do it like i did ,you will not need to remember to turn off your foglights separately . The foglights will furn on when you turn on the tail lights and...

ok so yesterday i was driving back to home, and i have VERY low gas, and about 0,5 miles before nearest gastation my car 98 GSX starts to sputter because there was no fuel at all :/ :ohdamn: ok i got to gastation some how :/ and after, the car runs normal . And today i got error code :/ I...

hi guys :D I am going to buy some Ebay exhaust system for my 98 eclipse gsx awd . And i undecided which one to buy :/ there are many of them on ebay :/ so im asking you guys to help me find good one that goona fit my 98 gsx and its gonna be 3in and looks like n1 exhaustim asking to fit my gsx...

hi guys im just wondering if can i put test pipe on my stock exhaust in my 98 gsx ?? will it sounds better ?? more hp ?? idk thx anyway :):hellyeah:

Hi everyone :D just looking for a little photoshop help I am thinking about which color I want to powder coat my wheels hmm i thing flat black or brown or dark gray or goldAnyways please help. Thanks a lot \ Here is the pic I would like edited.anyone please

i have 98 GSX 7bolt rebuilt engine and i just want to make sure that the torque spec for crankshaft bearing cap is 18ft/lbs ??. i found it at manual but to me is lil weak :/ idk thx for answers :DDSM :D

Other than a boost leak, what could be causing my car to stutter/hit fuel cut at only 10 psi.I just recently installed hard IC piping and a Greddy RS bov. I did a boost leak test and found some leaks at the injectors. I replace those injector seals and it still do that :/ and if i rais the...