The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Kiggly Racing
Please Support Morrison Fabrication

Search results for query: *

  1. snakeyes711

    1gb no power, boost,lean

    Ok, stock 6 bolt. Used a 2g mas, 580cc, maft tuner pro, s16g, 7" FMIC, 2" pipes. Innovate LM-1 wideband. ran great. I parked it for a few days after a family vacation, and when I started it back up after it never ran right again. New ECU, mas, turbo nothing changed.I removed all of the AM...
  2. snakeyes711

    Bad ECU? Lean WB zero power

    I'm guessing this is where I need to post. My DD 1GB has a bad problem I have zero power, almost no boost charge, and it goes lean around 5K...like massive lean falls on its face and I seen 18 on the WB... didn't do that anymore. The ECU pulls back timing to nothing. knocks like crazy. No power...
  3. snakeyes711

    WB lm-1 install

    I got a used LM-1 from a member, and received it yesterday. I used a small power invertor I have that has a aux plug, and checked it out. Worked fine. Sensor was good, and all. Is well. although I didn't receive an (analog out) cable for it, so I got a 3.5 sterio cable for it no problem. I used...
  4. snakeyes711

    logger wiring 12v mmcd

    What pin do you use to wire up a 12v wire to for the palm? Don't that then charge the palm? I'm getting tired of every time I really need to use it, the battery dies. I can't figure out the scheme I have for it. Does it need anything between the 12v signal, and the pin?
  5. snakeyes711

    Triad dsm group.

    I'd like to get up a dsm group in NC, based in the triad citys. Winston Salem, Greensboro, High Point. Areas. Anybody up to it?:hellyeah:
  6. snakeyes711

    14b into 16g, machine housing numbers.

    I been going over some numbers here. these numbers are from the s16g compressor wheel.14b compressor wheel is: (ind.) 1.695" (exd.)2.285"The stock compressor inside diam. is 1.725" +-.001"that gives the space between the wheel, and the housing 0.030"So I need to machine my housing out...
  7. snakeyes711

    Injector issue

    reant on!!! I'm pretty pissed, I got a injector kit and went to install it today got it all apart and realized these hard plastic tips for the injector were like twice as long as the old ones. I called them and told them, he said cut them, pretty much your on your own. As thats the part number...
  8. snakeyes711

    MAS screens

    Has anybody removed them, and kept them? I put mine back,a nd recently I noticed my LFT is way up in the 130's. I took off my intake pipe,a nd seen my bottom screen in the MAS is gone...I also noticed the compressor blades on the turbo are a bit chipped now. I think I ate my screen up, and spit...
  9. snakeyes711

    Riken Raptor Z rated?

    I got a guy that has 4 Riken tires that came off his Porsche 944. He went to a different tire. The thing is the tires are different sizes. two 225/50/16, and two 205/55/16. These are Z rated tires, and he has them for a price you can't beat. I'm confused as the size difference though? I guess...
  10. snakeyes711

    General reset ecu runs better?

    I only found maybe two threads after searching this , only one was from 2003, and none really had a concrete answer why after resetting my ECU my car seems to have more power. As in it pulls stronger. My fuel trims are hovering around Low 114%, mid 107%, high 104%. When I reset the ecu the low...
  11. snakeyes711

    Best "Quality fuel"

    Anybody tested different fuels in our cars? Whats the best fuel you've found to work for you. I've found that Shell, and some STP octane booster does wonders for my car.:thumb:However I used to swear by Amoco/Exxon fuel.
  12. snakeyes711

    stripped timing belt teeth

    I stripped the teeth off the belt at the crank pulley yesterday.:notgood: I noticed some extra noise by the belt area, and seen it was a bit chewed on the inside. It ran fine, I was sitting at idle at a light, and the engine just cut off. I rolled it back down the hill backwards into a parking...
  13. snakeyes711

    Future for tuning is here for turbo engines!

    Does any body get Hot Rod magazine? They have a article this month on a 2.0 liter turbo engine with direct injection. They say the fuel rail pressure is over 750 up to 2,200 psi!~!WTFYou can buy kits for some cars now. Like Saturn sky, Solstice, Colbalt, HHR just to name a few. They claim...
  14. snakeyes711

    intercooler install DIY pics

    I figured I'd post this here for youo guys to check out what I'm ready to do this weekend.I got a FMIC from CXracing. I got the 28x6x3 with 2" inlets. After I did some researching about what size to get thats what I ended up with.As for piping I looked at a million kits, even CX quoted me...
  15. snakeyes711

    FTo2? LTF high,

    Today I removed the lower honey comb, and the FTo2, an low fuel trims went haywire? Also the o2 sensor was reading 0.00 volts at idle. I could tell it wasn't running quite right. The FT o2 read 100% at idle. but at cruise it was up to 167% at times?Should I replace the honey comb or let it...
  16. snakeyes711

    Double intercooler?

    I been thinking on getting a front mount. I've been studying on how, an dwhere to route my lines for it. Then I came up that I could connect the two intercoolers together, and run the stock one too. Has anybody done that or would it just be too much of a drop for pressure to do it?How I'd run...
  17. snakeyes711

    new alternator brushes

    I didn't know where else to put this at, and didn't hit anything on a search about where they sell alternator brushes. Anybody?Thanks in advance!~jake
  18. snakeyes711

    Great! timing jump

    Yesterday, I was playing around in a old parking lot after it rained. I accidentally missed a shift , and revved the engine to 7,500k. Then car didn't feal right after that it'd build boost, but there was no power. The engine didn't sound different. But it did sound like the #1 cylinder was a...
  19. snakeyes711

    i really need to know how to remove the axles

    A small crow bar, and find a place to pry where if you put pressure its not going to break anything. It takes a bit of coaxing to get them out.
  20. snakeyes711

    blown turbo/ rebuild? or buy another?

    Its blown gotta be now today It sounds like a vacuum cleaner when if it boosts at all. Then thats followed by white smoke out of the exhaust. If I boost at all it'll smoke bad. If I keep it in the vacuum side it doesn't do bad just puffs at idle.So should I rebuild? I can get a kit on Ebay...
  21. snakeyes711

    wHATS WRONG HERE?

    Sry about the caps there. I can't understand whats wrong here. With my logger plugged in It streams data. Only when I upload it to the computer it looks weird in open office. A few weeks ago I logged a run, and it showed columns for each param. Tonight it logs this now.RoadSurge.com - CSV...
  22. snakeyes711

    MMCd Debug?

    Upon researching this topic, I only came up with a few hits none of which address this. I understand MMCd completely, well almost I can't figure out why, or what debug is used for? Is it only for making sure the ecu is communicating? Or can it be used to fix problems?In my debug I see about...
  23. snakeyes711

    Oil in coolant? turbo maybe?

    Ok, a few weeks ago I started noticing trace of oil specks in my coolant. My first guess was the head gasket. After doing some research, I found that the oil cooler its possible to pass oil in the coolant. I drained all the fluids, and found the oil cooler was finger loose. So I took it off, and...
  24. snakeyes711

    oil in coolant..turbo?

    Ok, a few weeks ago I started noticing trace of oil specks in my coolant. My first guess was the head gasket. After doing some research, I found that the oil cooler its possible to pass oil in the coolant. I drained all the fluids, and found the oil cooler was finger loose. So I took it off...
  25. snakeyes711

    (VID)Does my turbo sound like a wood chipper?

    I can't find anything searching about this sound. LOL forget the lawn mower sound my flex pipe is leaking. :ohdamn: The camera makes it sound a lot louder for some reason. Yu can't hear it if your listening under the car.heres the linkYouTube - 100 1937
  26. snakeyes711

    done with maint.

    So, after buying this basket case its coming together nice. So heres what I have done so far.New transmission Changed fluid in tranny, case, and rear diff. new Transfer case St. 1 exedy clutch both front drive shafts attached rear drive shaft, and got it bolted in. Timing belt kit/new pulleys...
  27. snakeyes711

    Manual Tranny swap problems

    I'm trying to put my transaxle back in, and running into problems. I can't get it back up in there to line up straight. The back corner hits the clutch housing, and the part where the axles slide in is hitting the back of the control arm. That part is almost impossible to remove without removing...
  28. snakeyes711

    new DSMer!

    Whats up, my names jake. I just got a new(well new to me) Talon TSI recently. Its tthe AWD model, and man it needs some love. First off I'd been looking a dsm's from here clear across Tennessee in hopes of scoring a Eclipse GSX. They are rare as hen teeth around here. Closest one I found was...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top