The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners

  • Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;)

Please Support RTM Racing
Please Support Morrison Fabrication

Search results

  1. BrokenTsi

    ECMlink RCI 2200cc injectors wont start or idle correctly

    Hey, its DrewJ. this was just brought to my attention as we were just discussing this on Ecmlink forums.When I get some free time, I can remote in to your laptop and check the tune myself. Since these injectors are 2nd hand, we don't know for sure how the original owner treated them, or if...
  2. BrokenTsi

    PTE Turbo reliability discussion

    Which PTE turbo?: T4 6466 DBB Balance shafts?:No Ported OFH?: Yes Where are you sourcing oil from?: OFH Size of feed line and restrictor?: -4AN feed line w/ PTE restrictor it came with Has the turbo blown?: NO How many miles did it or is it lasting: 2k miles, never seen under 40psi making...
  3. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    Good to know. I'll probably toss an evo sensor in there and try it out. Thanks!
  4. BrokenTsi

    1G End Case broken

    The only fix is to replace the end cover after re-torquing the 5th gear nut. :thumb:
  5. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    My car is very noisy. Tubular Kframe, solid rear bushings, built tcase, solid driveshaft bushings, etc.
  6. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    From what I was told, they are the same.. I don't care, I don't use either.
  7. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    No. Magnus V3 is 6 bolt only.
  8. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    I'm just going by what this dyno does against another dynojet that has seen the same cars. Calculations say 905 on another shops dynojet. I don't really care what it reads, I reference everything to a mustang dyno anyways. But thanks for the compliments. I don't speculate, I race and get...
  9. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    Simple patch harness and for those who use a knock sensor, bolt in a 2g knock sensor.
  10. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    I will not be changing out this turbo for a very long time. I will run 8's next season on the 6466, just gotta change up a few things on the car.STM's RS made 860 on 6766 at like...50psi. The 6466 has 6266 spool, and will make more power then 6766 until the 6466 is maxed out. I still got...
  11. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    I made the pull to 8500.
  12. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    Unless its a PPG dogbox, all "built" transmissions are stock transmissions. Nobody can make the gears stronger. Its a stock rebuild by Raif @ RRT. Also, my car isn't that heavy. Maybe 2650 witout me in it. That really helps.
  13. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    I only used the dyno at STM. My buddy at Mtuned convinced me to to put an Evo 8 ecu and helped me out with the tuning. The tune isn't conservative. My small runner manifold and unported head keeps me from making 800 at this boost level.
  14. BrokenTsi

    6466, Evo 8 ecu 772/530 Mustang dyno

    I just wanted to post my dyno graph on STM's mustang dyno.quick mod list: 2.0 aluminum rod, wiseco 1400HD 9.0:1 6466 open T4, .96 housing unported head, 1mm+ valves, ST duals, FP5R cams Magnus V3, stock TB Dragnfly T4 manifold, 1.25" runners Race Components fuel system, 2200cc injectors...
  15. BrokenTsi

    6466 Dyno

    DrewJ 1g Talon PTE 6466 9.7 @ 154 Evo 8 ecu - YouTube
  16. BrokenTsi

    WCF Roll Call List... Nov 1-3 at MIR

    I'm trying to make it.
  17. BrokenTsi

    21st ANNUAL DSM/EVO SHOOTOUT

    New Personal best... 9.69 @ 150. 6466 T4 on Evo 8 ecu. :)
  18. BrokenTsi

    21st ANNUAL DSM/EVO SHOOTOUT

    The RCI jackets at Summit Racing are affordable and do the trick.
  19. BrokenTsi

    New stock 7-bolt block record

    Are you stock 7 bolt block as well, urban smoker?
  20. BrokenTsi

    New stock 7-bolt block record

    You are correct.It's a friendly battle which has been very fun. Will comes back from Afghanistan tomorrow and then it's nonstop work in the garage until we get to the track to try again. :thumbup:
  21. BrokenTsi

    21st ANNUAL DSM/EVO SHOOTOUT

    I've raced in DSE the past 3 years. I'm OK with the exhaust rule. I say BRING IT. It will make the competition a little more fun. It will also bring in all the guys who should be in DSE, but were forced to race Quick 16. Maybe a turbo size limit needs to compliment the possible change of...
  22. BrokenTsi

    Low Timing and Still Knock

    Nice work on troubleshooting this issue.I suppose the next step is to replace the ECU. There is nothing on our engines that will tell the ecu to retard timing, other then the ECU itself. Good luck, and keep us posted.
  23. BrokenTsi

    Low Timing and Still Knock

    Ecmlink assumes you are at 5* mechanical base timing.During the areas of knock, according to your wideband and assuming that the log reflects what is on the gauge, doesn't seem too lean to me. You are barely at any type of real load at 3400rpm, however I can tell you that are most likely...
  24. BrokenTsi

    Low Timing and Still Knock

    Something is definintely wrong. You have your knock sensor disabled until 3400rpm which is right where you start to read knock on the datalog. So its probably detonating or reading false knock right from the get go. I dont see an issue with the amount of timing being ran during spool up...
  25. BrokenTsi

    Official Bench Racing Thread (how fast is my car/how much HP can I expect)

    I used to have almost exactly your same setup, but with eagle H beam rods, and I had that engine for 20k miles and trapped 133+ consistently on a 30r @ 33psi.A customer of mine, has scat/mahle 6 bolt with a 6262 and has been running big boost for years. Never been to the track, but I think...
  26. BrokenTsi

    New stock 7-bolt block record

    *quick update*We've been very busy, but we're still running the stock 7 bolt. We're fixing to put it into the 9's this summer.Will is currently deployed to Afghanistan, but he'll be back soon...then its GO time. :thumb:
  27. BrokenTsi

    Why/Why Not Meth/Water?

    I ran low 10's on pump/meth. It was sooooo much fun on the streets. I ran 35psi daily. I'm a big fan of it.
  28. BrokenTsi

    5th gear pops out

    Its easy to do. Jack the car up, remove the wheel, drain the fluid, remove the case, notice how your 5th gear is probably trying to push itself thru the end case because its loose, replace the nut or at least torque it back to spec for now, and reinstall. 2-3 hours if you work slow...
  29. BrokenTsi

    6466 Dyno

    Nice work! I have been strongly considering this turbo in the vband housing for 2013.
  30. BrokenTsi

    I went 6.4. :p

    I went 6.4. :p
  31. BrokenTsi

    HTA GT3586r vs twin scroll gt37r on built 2.3L

    For 650whp, I would do 3586HTA, especially since you want it to be streetable.
  32. BrokenTsi

    New stock 7-bolt block record

    We're gearing up to give it another go real soon!
  33. BrokenTsi

    Compound charged talon wins DSE

    I got paid $75 for 3rd place if that makes a difference..... :/
  34. BrokenTsi

    Fuel Pump Wiring

    That's exactly what I'm thinking. The black/white wire is a power wire for the fuel pumps. I was trying to see if there was more to this story. :p
  35. BrokenTsi

    Fuel Pump Wiring

    Is this a car you just purchased? When was the last time it was running?
  36. BrokenTsi

    helicoil the intake side

    so do I, I just use the stock bolts with my Magnus intake, seems to work fine.
  37. BrokenTsi

    helicoil the intake side

    Im assuming you're referring to the head. There are 2 sizes. 8x1.25 and 10x1.25. Which one needs repair?If its the 8x1.25, I've repaired them to a 8x1.25 using the proper heli-coil kit.Same goes for 10x1.25.Basically, when you heli-coil it, you're drilling it out large enough to...
  38. BrokenTsi

    Compound charged talon wins DSE

    Aww snap! Now this should be pretty cool. Another auto compound turbo car? (god dammit)
  39. BrokenTsi

    what catch can are you running

    +1 more for Calan. I have mine bolted to the front of my transmission.
  40. BrokenTsi

    Found my culprit for my detonation, melted pistons, blown head gasket

    so how aggressive was the timing? and how did you find that out?
  41. BrokenTsi

    Compound charged talon wins DSE

    Even with a pretty big catastrophic failure, I had an awesome time. Nice job, car was very consistent and fast!
  42. BrokenTsi

    CnC staging brake ?

    Yup, thats pretty much it. You will need to buy some adapters to run the -3an SS lines. I forget what the thread pitch of the master cylinder and prop valve is. The CNC brake is 1/8" NPT. I used one straight and one swivel'd 90* 1/8" NPT to -3AN adaptor.
  43. BrokenTsi

    CnC staging brake ?

    I actually kind of forgot how I did it in my car, but I'll take the best pics I can and post them up in a few days. Once you see how I did it, you'll realize how easy it is.
  44. BrokenTsi

    New pictures

    I know this car. A local dropped it off to me last year to get tuned but it had some issues that needed to be addressed first so I wasn't able to tune it. Looks like you got it all fixed up!
  45. BrokenTsi

    CnC staging brake ?

    I installed mine in-line with the prop valve. No cutting of lines required! It locks up the front right, and rear left wheel.
  46. BrokenTsi

    15.5 Seconds- What am I doing wrong?

    Actually, from what I see in the logs...you are adding tons of fuel thru the MAF calibration and then pulling fuel with the fuel sliders because of it. In the end, your wideband's AFR's are all that really matter, but your MAF readings are skewed and everything else in the tune will not line...
  47. BrokenTsi

    15.5 Seconds- What am I doing wrong?

    I looked at log 3. 1.1* of timing retard isnt crazy. Maybe its time for a colder spark plug or maybe tighten up the gap. I see that you're activating the knock sensor >3000rpm. Perhaps there is an issue with your knock sensor or maybe your plugs/wires.Try a BPR7ES with a tighter gap...
  48. BrokenTsi

    We're looking to further the stock 7 bolt block record on Friday!

    Good question. If the Evo guys can do it, I don't see why Will's car will have an issue. He revs it to 8300ish at the moment.
  49. BrokenTsi

    We're looking to further the stock 7 bolt block record on Friday!

    In the 10.33 run, Will's car had the basic weight savings...no rear interior, no a/c, carbon hood and hatch with the stock glass. With the addition of the cage, its not much lighter than stock. Since then, its about 75lbs lighter now so hopefully that helps alot!We have not weighed it...
  50. BrokenTsi

    We're looking to further the stock 7 bolt block record on Friday!

    You know, that would be cool. I'll send Bill an email today asking about it.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Feal Suspension Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com OHM Racing Raven Fabrication RixRacing RockAuto RTM Racing SouthBay Fuel Injectors STM Tuned VR Speed Factory
Top