Dyesuperman said:

Finally got mine on after it sitting in my garage for 2 months

You must be logged in to view this image or video.

IMG_3781R by Dyesuperman, on Flickr

Who needs front bumper clearance, right?

You must be logged in to view this image or video.

Untitled by Dyesuperman, on Flickr

Overall it fit very well, I am very pleased with it for the money. I would buy another one no doubt

Click to expand...

Looks amazing as always man! Absolutely beautiful!

my dreamt dsm said:

Did you two have to fold the front bumper to fit the lip? I could see that it's short of reaching the ends of the bumper.

Click to expand...

No, I just centered the lip and attached it from there. It is a 1/4" off on each side, but it doesn't bug me. Mine (I got the Extreme Dimensions CF one) is VERY sturdy, I'm confident it will survive,

I bought the Extreme one and the Carbon creations one in the group buy. Both of them failed in exact 100% fitment. As stated both short of reaching the sides. And right where the bumper curves to the outside. Both lips under cut the bumper. As I can see in the ebay one it fits a little better.

Dyesuperman how was fitment, did the ends of the lip reach all the way out to the bumper.

Sorry, I have ocd

FOR THE RECORD....

The lip in the original post is NOT an Extreme Dimensions Lip (i'm looking at you my dreamt dsm!).

The one ms JAX over there has, our Carbon Creations Lip, IS our product.

Here are some basic Test fit images:








If you have our lip, please ensure it is installed properly. as you can see, even with just a basic mock up, the end corners line up, as well as the front of the bumper.


Not trying to thread jack, just trying to clear things up, since a few people believe the lip in the OP is an Extreme Dimensions product.

Thank you,
Irving

Am I the only one who thinks it's funny in the ebay ad they called it "ECLISPE"

thanks Irving. Is the one in the picture a newer revised lip or same one in the group buy?

my dreamt dsm said:

thanks Irving. Is the one in the picture a newer revised lip or same one in the group buy?

Click to expand...

Its from the same factory as all the previous 135 lips sold since we started making that part.

I guess I'm the only picky one .
The following pictures are that of the original rm dsm lip I believe. But I'll take some pictures of my lip Thursday.

my dreamt dsm said:

I bought the Extreme one and the Carbon creations one in the group buy. Both of them failed in exact 100% fitment. As stated both short of reaching the sides. And right where the bumper curves to the outside. Both lips under cut the bumper. As I can see in the ebay one it fits a little better.

Dyesuperman how was fitment, did the ends of the lip reach all the way out to the bumper.

Sorry, I have ocd

Click to expand...

Fitment on it really was much better than I expected it to be. Mine goes right to the edge and doesn't have any problems around the curve either. I will likely be buying another one to throw on a good bumper (aka one I don't use very often and scrape everywhere ) for meets and shows

I notice that all the cars that have been showed in this thread are eclipse's... anyone know how well this would look on a 2gb talon?

Thanks Irving for the help. But I guess I'll just sell one of the two lips I have and spend the funds on my motor
I'm not able to send pictures through my ipad, it's not going through tuners somehow but on my part pictures will be posted when possible.

my dreamt dsm said:

Thanks Irving for the help. But I guess I'll just sell one of the two lips I have and spend the funds on my motor
I'm not able to send pictures through my ipad, it's not going through tuners somehow but on my part pictures will be posted when possible.

Click to expand...

If this is in regards to the PMs we've sent, you can always email those images to [email protected]

my dreamt dsm said:

Did you two have to fold the front bumper to fit the lip? I could see that it's short of reaching the ends of the bumper.

Click to expand...

Nope. I heated the lip to take some waves out and installed similar to ExtremeDimensions method.

Anything for a 1G?