that's funny...I was just searching for this earlier and couldn't really find too much info. I guess you have to call up bullseye and ask them since their site is hard to find anything like this on it.

That is about a true story. There is no listing on there sire for any housings at all!! I heard a few people say that it cost 179 or so but I need to know for sure. I also need to know what 02 housing it bolts up with.

Are you looking for a housing that is a bolton to a dsm flange or just a different/smaller housing?

bullseye turbine housings

Well, I found this on bullseye's site. I guess you have to call for pricing. Hey, if you do call can you shoot me a pm on how much they are?

Give slowboy a call. I got one from there, but I'm still looking for a cheap h1c.

slowboy told me around 300 for the bullseye housing little bit more for the full kit with gaskets and such

Not to knock Slowboy but $300? Try G-Pop Shop, or Bullseye direct.

A customer of mine had a DSM bolt-on housing he had purchased direct from Bullseye for the HX35 shipped me for a rebuild and the invoice from Bullseye was $210 including shipping; the housing was set up for an external gate off the o2 housing. That was last November, I believe.

You can also buy them straight from BEP. Just send them an email or a call. I would rather go through them than one of there vendors.

jusmx141 said:

Not to knock Slowboy but $300? Try G-Pop Shop, or Bullseye direct.

A customer of mine had a DSM bolt-on housing he had purchased direct from Bullseye for the HX35 shipped me for a rebuild and the invoice from Bullseye was $210 including shipping; the housing was set up for an external gate off the o2 housing. That was last November, I believe.

Click to expand...

They sell them for $300 with both oil lines and all gaskets needed.

Not to bring this thread from the dead but Does any one know where else i can get the hx35 dsm housing I have called bullseye and they wont have any for 8-12 weeks tims turbo dose not answer.Dtm parts does not answer.... so im kinda stuck i just got my hx35 and need to get it on asap the e316g needs a mega rebuild.

G-Pop Shop and Slowboy are also distributors, but they most likely do the paperwork and Bullseye will drop ship to you so if BEP is out, so are all the distributors.

Word on the street is that the last batch from Bullseye were either cast wrong or improperly-machined; how true that actually is I'm not sure. I just bought two of them about three weeks ago and they were both machined fine and came in a timely fashion.

Slowboy no longer carries them ill give g pop shop a call. thanks

Try timsturbos.com, i think they have them for like $250.

Bringing this back from the dead for the 2nd time... Where is everyone getting there hx35 Mitsu bolt on housings? I saw extreme psi has them for $280. Anyone find them cheaper?

Here's the link to extreme psi's listing...

EXTREME PSI : Your #1 Source for In Stock Performance Parts

S&R Performance also list's them for $279..

here:http://www.sandrperformance.com/Bullseye-Power-HX35-DSM-Turbine-Housing_p_420.html

Hey, guys don't know if this helps but I have been researching hx35 turbo setups and now getting ready to buy new setup for next season and this is my base. Hx35 t25 Mitsubishi t25 exhaust housing external tail 38 mm wastegate (which I bought for a guy on this forum, thanks) and a o2 housing so I can still use my cx racing manifold. I use DSM Graveyard, they have a great website http://www.dsmgraveyard.com . They carry all you need for bullseye, Holset turbos and accessories. I have a big 16g and Monday my car is going on the dyno at Magnus and we will see the hp we get. I have 550cc injectors and all the supporting hardware for around 400 hp and next year I hope next season with the hx35 get 450 to 500 hp with 850 cc injectors, Oh I just installed a DSM link to run it. I'm excited the Internet thing is an amazing resource for car enthusiasts.

dkalfop said:

Hey, guys don't know if this helps but I have been researching hx35 turbo setups and now getting ready to buy new setup for next season and this is my base. Hx35 t25 Mitsubishi t25 exhaust housing external tail 38 mm wastegate (which I bought for a guy on this forum, thanks) and a o2 housing so I can still use my cx racing manifold. I use DSM Graveyard, they have a great website Search Results for "motercyclepartz.info" . They carry all you need for bullseye, Holset turbos and accessories. I have a big 16g and Monday my car is going on the dyno at Magnus and we will see the hp we get. I have 550cc injectors and all the supporting hardware for around 400 hp and next year I hope next season with the hx35 get 450 to 500 hp with 850 cc injectors, Oh I just installed a DSM link to run it. I'm excited the Internet thing is an amazing resource for car enthusiasts.

Click to expand...

wow, a hx35 in a t-25 housing!? I want to see this

DSMGraveyard - Directory
http://www.dsmtuners.com/forums/newbie-forum/416943-dsm-graveyard-built-hx35.html

That last line "Internet thing", this made me and rofl.

good luck with those 550's and 400hp .

Don't buy from dsmgraveyard you should read their feedback is horrible.
TheDSMGraveyard.com - Directory

A lot has changed, I agree dsm boneyard is very slow and can't seem to get there kaka together. I kept the 550 cc injectors and added a 20g cast manifold along with 44 mm HKS waste gate. Marco from Magnus have been friends even while my talon in the garage for a decade. We dynoed my car at 378 whp at 23 psi with a 255 Walbro in tank fuel pump. He said they weren't maxed and no need for big fuel system.

checking my garage at the moment i might have what you are looking for
i remember i had a bullseye exhaust housing somewhere for a big turbo, ill check the specs on it if i find it.