The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support JNZ Tuning
Please Support Morrison Fabrication

Recent content by xharlequinx

  1. Car gutted: insulation options

    Does anyone have any suggestions for insulation spray or layering for a gutted car?
  2. not starting, not spark to fuel pump

    I say fuel pump relay.. couldn't hurt to test with another one. 2 minute job.
  3. Dsm shops

    Hey shane, Thanks a ton, I'm actually in South San Jose, but come to Los Banos, Fresno area here and there. I was going to buy a starion or pair of Starions from Dave Wollin, who lives out an hour and a half east of Los Banos. I ended up picking one up from San Diego, and am planning on...
  4. Dsm shops

    Anyone know of a dsm knowledgeable shop in Fresno area ? I'll need to have a swap done if I pick up this car. Thanks !
  5. Fwd tranny builds?

    Just street. I would hate to get wheel hop though if I'm putting too much power down. I know that I can put mini van tow spacers in the rear suspension to prevent traction loss, but I'd like to be able to drive at 400whp or 430whp without feeling it all go down the toilet in 1st and 2nd gear...
  6. Fwd tranny builds?

    I have a 4g64 block w 63 head, 30r Garrett, and trying to figure out whether I should put it in a gs Spyder 2g or not...it's the only Mitsubishi other than mighty max that can drop in without much engine bay/ motor mount fab, from what I understand. If I do this, I might as well keep fwd, but...
  7. 4g64/3 from 420A question

    Thanks a lot! My engine is already assembled and in the mighty max. but it's hooked up to that stock tranny in that POS since I never went through with building that truck. It's a block from an earlier 1991 4g64, so I'm assuming I'll probably need an adaptor plate, yea?
  8. 4g64/3 from 420A question

    oh this is great news then. So I can pretty much drop it into a spyder and make it awd getting a 4 bolt rear, drive shaft and awd tranny? obviously a bit more than just that, but basically?
  9. 4g64/3 from 420A question

    I'm swapping a built 4g64 shortblock with a 63 turbo head into something...but can't decide. Of course I'd love to mess around and throw it in a foxbody or even a 67 fastback stang but I'm not sure anyone shop would be up for that project. I was thinking about putting it into a 2gen eclipse...
  10. LA shop??

    Thanks. looks like I will be taking both cars to them. Much Appreciated!
  11. LA shop??

    Sweet. So they'd be pretty knowledgeable about doing any sort of swaps and fab work?? motor mounts, bellhousing adaptors, tuning all that good stuff? Thanks a ton!
  12. LA shop??

    Hey everyone, I've been a dsmer since 2004 but have been out of it for a few years. I'm getting enough money to where I can get back to messing with my tsi awd & mighty max with a 4g64/3 and I'm in LA frequently now. I've heard great things about the DSM shops and cliques in Socal and just...
  13. running too small of an exhaust

    hmm so would u recommend an E cut out or just go 3inch straight shot all the way back
  14. running too small of an exhaust

    What are the negative symptoms for running too small of an exhaust with a big turbo set up like gt-30R and bigger?
  15. O2 Sensor? What else?

    I have an awd tsi Talon 91 and everything has been going great, up until now, when I just got a check engine light. The odd thing is, the check engine light doesn't come on until a minute or two into the car warming up. Sometimes not even until I drive. That is why I would think its an O2...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top