1. Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;)

Turbizmo
Last Activity:
Feb 21, 2012
Joined:
Jul 3, 2005
Posts:
421
Likes Received:
0
Vehicles:
1

Share This Page

Turbizmo

Proven Member, from California

Turbizmo was last seen:
Feb 21, 2012
    1. So Cal 420a DSM
      So Cal 420a DSM
      Did you fix your fuel pump problem? I think my fuel pump is bad. Everytime i start my car it shuts down.
    2. Fotowntalon
      Fotowntalon
      yeah i had the same problem with crower, it eventually stopped after a week or two and letting the ecu learn the new curve. I now have an afx computer which learned the curve quicker after i installed it. I cant remember if u mentioned it, but new springs also helped it idle smoother. If all else fails, you could adjust your throttle stopper, to make sure that air is always getting in, should help prevent it from dying.
    3. dsmking101
      dsmking101
      thanks bro for everything it helped alot
    4. dsmking101
      dsmking101
      ok so when i t the oil sending line on the back of the block do i cut the line and install the t is it a 3 way t two sides oil sensor line and the third the oil feed line ....or do i have to take out the sensor .....and at home depo were would i find this t and is it hard to make and expensive ...please let me know as soon as you can thanks bro
    5. dsmking101
      dsmking101
      hey bro when you turbod your 420a were did you run your turbo oil feed line and were did run the coolent line i bin trying to figure out were to connect those lines and i got an idea but i want to make sure from sombody how has done it befor ill appreciate the help thanks
    6. 4pitts2bmx0a
      4pitts2bmx0a
      howed the tranny work out was it a 3.55
    7. gsxofftheline
      gsxofftheline
      Go to superbrightleds.com, or get the flexible 96 led bar, take apart your headlight metal clips, then use a heat gun around the edges while prying it apart.theres a black plastic piece at the front inside, before taking it out, notice theres a 1/4 inch clearance at the bottom, thats where the lights will go, take out the black piece, put in the led strip face forward, bring it all the way across to the end, drill a small hole at the corner of the back headlight, so the wires stick out, glue it in place or use really strong 3m tape, put the black plastic piece back in and the rest of the headlight, then tap the positive wire to the parking light wire, then the negative to a ground, such as the blot that holds the headlight together. test it out before putting the headlight back together. then when putting the headlight back together put a thick clear adhesive around the edge and put it together and put the clips back it. let me know how it works bro.
    8. DSM_ThuNDeR
  • Loading...
  • Loading...
  • About

    Home Page:
    http://www.NightFuzi0n420a.com
    Location:
    California
    City:
    Salinas
    State:
    California
  • Loading...
Support Vendors who Support the DSM Community
Archer Fabrication ECM Tuning ExtremePSI Feal Suspension Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications OHM Racing RockAuto SouthBay Fuel Injectors STM Tuned Track Decals Track Sculptures VR Speed Factory WheelWell.com