Guess it's time to see how the DSM crowd is kicken now a days. Still have my 95 GST. I run it for a few months in the summer then put it away. To be honest got bored and I'm currently in a "German phase" playing with Audi's. But on those nice summer days I always go for a drive with the Eclipse...

This is how you "preload" the studs. You set the torque to 18lbs and once you reach that while tightening you will reference where the arm of the torque wrench is and then go another 90 to 100 degrees. So the arm is at 12:00 and you will continue to turn to 3:00 , "90deg". The bolt is allowed an...

I'm sure from the vendors point of view they must cringe when something like this happens. Margins are thin to begin with in this economy and to have to exchange a mis-boxed part probably just ate that small margin. Not to mention people who are not so honest and scam vendors. Running a retail...

In a negative world I just wanted to say something positive about a vendor, Mach V Motorsports. The other week I ordered some gauges from them, the back-light color for the gauges were amber. They were shipped quickly and after inspecting them I discovered that while the box stated amber the...

So you want to rotate and use the elbow set up like in TurboDSM86's picture right ? I did a quick search and here is a link to a site that sells the elbow:Turbo XS Blow Off Valve Accessories UNIVERSAL 0 - 0 H-90ELBOWHope this helps LOL

Here is a link where TurboDSM86 recirculated his RFL: http://www.dsmtuners.com/forums/turbo-system-tech/182340-rfl-recirculating-i-did-pics.htmlThere is the possibility that the valve on the BOV could either get pushed open under WOT/increase PSI "this would cause a lean condition" or be...

From you're description of your problem is sounds like it is not BOV related. At idle the BOV is not being used i.e. it is not opening up as you are not introducing any additional pressure at idle therefore the BOV is not venting.My first suspicion would be the IACS or TPS. Pushing in the...

I have one and love it. I monitor rpm and air/fuel with it as well. The reason I chose it was because I can monitor in real-time using the graph mode and record so I can play back and "fine tune" my boost curve. As an example I reduced the boost from 3k and gradually increased it to red-line so...

For me I used a grinder and then replaced with new SS from the local hardware store. For the nuts on the exhaust manifold studs I used MAP gas to heat up and they came right off.

Perhaps the video would explain what I tried to convey in my last reply: How To Videos Installing Upgrades For Your Car It has been using the narrow band analog output from the Innovate controller for the last two years and I was only using the heater connections from the OE sensor. No MIL...

Sorry I was not more detailed about the Innovate, yes the narrowband signal goes to the computer and the wideband goes to a Greddy Profec e-01"I made a how-to video on this as well". So I no longer had the need for the stock O2. It's been this way for a little over two years and this years...

Because I’m using an Innovate wide band O2 sensor that is mounted on the down pipe I no longer use the stock O2 sensor. During my turbo upgrade I eliminated the stock O2 sensor but doing so threw a cell on the O2 heater so I came up with this as a simulator.Parts: One used CPU heat sink...

I know this is an older thread but I just wanted to say this tip did the trick :) I ran into the EXACT same problem and I remembered reading this post awhile ago, did a search found it installed the bearings first shot.

Another fun thing is when I remove the silencer from the tail pipe and as I drive through town I'll sometime see a cop walking the beat. He'll hear the car and he'll stop walking and start looking at the car and edging to the curb of the sidewalk "in anticipation of tagging me". As I get closer...

There have been many times where I would come out of a store to see someone standing there looking at my car, peering in looking at the interior, looking at the wheels and breaks etc. Sometimes they will start taking pictures with their cell phones. I'll walk up to them and usually just get...