The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

pksystems

Latest activityPostingsVehiclesAbout

    • pksystems
      That was the problem. Nice and dark, until I rinsed it and the some of the dye started coming out. After a full rinse it was a dark blue. I drive my car in all conditions. (when it works) If it rains and you get some water on the carpet...
    • pksystems
      I didn't have much luck with the rit dye in a salt water bath. When you rinse it, most of it comes out. It eventually looks like it was a dark blue. I gave it a shot with Duplicolor vinyl and fabric paint, and it's definitely black now. Seems...
    • pksystems
      Not the greatest picture but here's my black and tan interior with black carpet and black speaker grills. I think it sets it off perfectly.
    • pksystems
      Cleaned up the freeze plug surface with a nylon brush on a drill, and hammered in a new plug with a coating of rightstuff sealant.I assumed the car had no coolant in it since it leaked out so fast, but it turns out, it's had water/coolant...
    • pksystems
      Played around with my hood bump extension/duct. I think I have room for aerocatch hood pins now after moving it back.
      • PXL_20240615_035528538.jpg
    • pksystems
      pksystems reacted to 99gst_racer's post in the thread Hood Pin Location....? with Like Like.
      Mine are toward the outside of the hood. I think this is where you are talking about. I didnt install mine myself. I had it done while my car was in the body shop. But they did tell me that the installation was very easy. Here's a good pic...
    • pksystems
      Toyed around with an idea I have for a stockish looking hood vent. I waxed my hood and made an overlay of the stock bump. Once the resin was cured I popped it off, and now I can have a base to play around with. White styrofoam is minimum vent...
      • PXL_20240529_020647499.jpg
    • pksystems
      A little more handling upgrades & carbon fiber goodnessAt this point the car is now caught up with maintenance and some nice little upgrades. So I wanted to further play with some custom alignment settings and stiffen it up some more.To...
    • pksystems
      Pulled fuel rail and injectors. Then blindly undid all the bolts for intake manifold. What a freaking pain.My block heater freeze plug is the source of the leak. It must have come loose over a couple years, before it finally burst.
      • PXL_20240525_035202796.jpg
    • pksystems
      While I was waiting 1/2 an hour for windows to do updates so I could drain the fuel tank, I put a piece of plastic over the hood, and built up some expanding spray foam on my hood. I think I can extend the hood bump by a couple inches, and build...
    • pksystems
      Filled the ole girl up with some E85 and hit the mountain twisties with the local subaru club over the weekend. We had an absolute blast and the car ran/handled amazingly well. I couldn't believe how well it tore through corners. Ended up almost...
    • pksystems
      Brackets I made with slotted holes, so I could adjust the position to get the screen tight against the HVAC bezel. I had some old red spray paint so I gave it a quick coat.Microphone for bluetooth calling installed at top of A-pillar.All...
      • 438095179_2440531426145593_372629431495113145_n.jpg
      • 438083335_1151966882792305_6063975593054162105_n.jpg
      • 438083293_816101280414322_8581119696277112410_n.jpg
      • 438125042_803868855029048_5659571554194781710_n.jpg
    • pksystems
      I found that the combo of OEM 2g drain tube, an AO customs silicone precut gasket and Evo 8 sealing washers and ARP thread sealant on the bolt threads results in a perfectly dry return line at the top and bottom.Today I continue waiting for...
    • pksystems
      Saw a thread posted on main page about best way to wire things, so thought I'd post here.Wired up my stereo. Crimped or twisted, soldered, and heat-shrinked all wires/connectors together. :)Ready to install it today.
    • pksystems
      Before I start pulling bits off the engine to fix the coolant leak, I decided to add a backup camera, and dual din touchscreen to car. I grabbed a JVC-560BT for cheap. It's basically just a tablet you mount in your dash. All media plays off the...
    • pksystems
      pksystems replied to the thread Unicorn LSD find.
      Old bump, but I believe I have this exact center diff.I bought it listed as a kaaz (I think) but when I started comparing it to other kaaz parts I eventually started to find Cusco MZ is probably what it is. I took it apart and have pictures...
    • pksystems
      Started making some 2G dual din stereo brackets. I'm putting slotted holes so I can make fine adjustments to get the touchscreen snug to HVAC bezel.
    • pksystems
      Picked up a JVC KW-M560BT dual din touch screen so I can install a backup camera.
    • pksystems
      It’s not a matter of IF your 2G DSM OEM door handles will break – it’s a matter of WHEN. Tony Davis has spent years perfecting this billet aluminum replacement to assure that this is a set of handles that will outlive your car. These will fit...
    • pksystems
      Finally pulled this thing back into garage to take a look at it. All dry rotted rubber vacuum caps replaced with vinyl ones. Car started right up, and was fine for the short drive around the block (with no coolant)I don't think it's a blown...
  • Loading…
  • Loading…
  • Loading…
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top