The Top DSM Community on the Web
For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.
Recent content by Nickolision
For sale 2g 1995-1999 Mitsubishi Eclipse Custom LED Tail Lights - USED
1995-1999 2G Mitsubishi Eclipse Custom Tail Lights (2GA/2GB).LED BAR DESIGN! LED BRAKE LIGHT LED TURN SIGNALCracks and shows wear,fully functionalUsed conditionMust be installed professionally,or upon buyers risk!Located in Sacramento, CaShipping on buyers expenseWith UPS Ground$450.00- Nickolision
- Classified ad
- 2ga 2gb diy dsm led
- Category: DSM Parts Classifieds
-
420A 2gNT rear disk brake swap
Check out my video on how i converted my drums to rear disc.I used all oem parts from a GS, all i had to do is get those backing plates and everything included it should all fit. Even the e brake cables which you have to get from inside the car.- Nickolision
- Post #4
- Forum: Newbie Forum
-
Coffee and Cars
im in Sacramento, but willing to make the drive if its close- Nickolision
- Post #2
- Forum: San Francisco Bay Area DSM Forum
For sale 2g 1995-1999 Eclipse Custom LED Center Piece USED
1995-1999 Mitsubishi Eclipse 2g center tail light modification.It’s off a 97 eclipse, so it has signs of wear and cracks because of opening the lens.IF you want a custom pair, message me directly or on Instagram @nickolisioncoThese are a service too, $150 plus additional shipping fees...$150.00- Nickolision
- Classified ad
- 2gb tail light tail lights
- Category: DSM Parts Classifieds
SoldFor sale 420A 1997-1999 420A Automatic ECU
came off a 97 auto 420a, might need reprogramming.shipped with UPS Ground included$80.00- Nickolision
- Classified ad
- Category: DSM Parts Classifieds
-
2G Car almost overheating
this happens when typically the thermostat is faulty or for my solution everything was replaced, just the coolant i used stopped having the cooling capabilities, I used a better coolant brand and never had a problem after- Nickolision
- Post #3
- Forum: Newbie Forum
-
420A 420a no spark
make sure that the camshaft holes are pointing straight up, this will make sure that the timing is set correct on the top end, of course if the camgears are set to position it should all line up- Nickolision
- Post #2
- Forum: Maintenance & Repairs
ClosedFor sale 2g 95-99 Eclipse Custom Tail Lights Halos
found these looks like they power on just need to be wired in, used for testing years backUsed, good conditionShipping with UPS Ground (+fees)thanks$250.00- Nickolision
- Classified ad
- custom dsm led taillights
- Category: DSM Parts Classifieds
-
1997 420A Mitsubishi Eclipse 2G
Finally, Rear disc conversion!MY car is a RS, comes with the brake drums in the back, this is a upgrade i wanted to do and got next to nothing achieving it! I grabbed everything from the brake caliper and bracket, backing plates, and handbrake assembly. I didn't have to cut or anything! The...- Nickolision
- Post #10
- Forum: DSM Build Journals
-
1997 420A Mitsubishi Eclipse 2G
Installed the complete set of 2GB Side Skirts!All oem parts from many different dsm, at first i got the 2GA ones and didnt noticed they were different. For mounting techniques, I tried magnets and they didnt hold to the panel like I wished. Eventually, just using the original clips, in tandem...- Nickolision
- Post #9
- Forum: DSM Build Journals
-
1997 420A Mitsubishi Eclipse 2G
Finally dropped the car on the Tein coilovers! I measured about a 3.75 front and 3.50 drop in the rear! Going for a bigger size wheel would make this look great- Nickolision
- Post #8
- Forum: DSM Build Journals
-
420A 2GNT Misfire cylinder 2 and 4
i would check out the coil pack next, i had some misfire issue sorted with all those 3 replaced- Nickolision
- Post #3
- Forum: Newbie Forum
-
2G Visual Guide: 1997-99 Front Bumper Cover & Components
Always so helpful with these visual guides!- Nickolision
- Post #2
- Forum: Articles: Exterior/Interior
-
Side skirt 3M adhesive
I tried many ways (velcro, magnets, 3m) to figure out my side skirt is pulling away from the body, only way i found out was using automotive goop and clamping a 1/8 peice of wood with clampsother alternative was to screw in a body screw and fill with primer. etc- Nickolision
- Post #13
- Forum: Appearance/Interior/Exterior
