The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Fuel Injector Clinic
Please Support ExtremePSI

Recent content by KYNgsx

  1. KYNgsx

    2018 Calendar? Should we design a new one?

    I would try and submit pictures, but there's always a requirement for current date stamps. Removing that requirement might get more submissions.
  2. KYNgsx

    1G Fuel Tank return modification?

    Bulkhead fitting. For me it's not about the size of the return line but the ease of using AN connections versus messing around with hoses and clamps.
  3. KYNgsx

    1G General tool inquiry

    Add a 14mm and a 17mm to that and you're basically good to go.
  4. KYNgsx

    Aluminum exhaust from scrap sheet aluminum?

    Nice job on the exhaust! Did you fart when you bent down to pick up the camera? :tease:
  5. KYNgsx

    1G Stock block 1g fp black.... Want to pick your brains

    1150's were maxed out on my car with boost at 30 psi. Upgraded to some 1650's and now my duty cycle looks much better; 60-70% with the boost set at 35 psi.
  6. KYNgsx

    1999 Eclipse Evo Swap

    Awesome project. I really like this picture, the signs just always kind of bothered me:
  7. KYNgsx

    1G New Cams and Lifters, will they work?

    Back when my motor was stock I dropped in some BC 272s and ran them to 8000 rpm for years with no problems. This was also on stock cam gears, springs, and lifters.
  8. KYNgsx

    Best GoPro Car Mount?

    It's actually mounted to the middle brace on the ceiling. Don't have a cage yet, but that would also be a good mounting point.
  9. KYNgsx

    Best GoPro Car Mount?

    Here's what I use for mounting my GoPro:http://www.filmtools.com/cameradept/movcamsupeq/carmounts/cadellini484.htmlIt's kind of overkill but has a lot of flexibility and allows for more mounting options than the suction cup.
  10. KYNgsx

    1G FP Green install issue. Water line?

    I used a new set of stock water lines when I installed my FP Black. I don't remember having any difficulties with it.
  11. KYNgsx

    Your most recent welding pics

    It's been a while since I had a chance to weld. Built a new exhaust for my truck:
  12. KYNgsx

    Help setting up/launching FP Black MT car

    My 60's aren't much better, but my car has a similar FP Black and manual trans setup. My best results come with the launch rpm set at 6500 and making sure I get on the gas early . It's taken a lot of practice to finally start improving my 60's on the new setup; finally got down from the the...
  13. KYNgsx

    1G Fuel Tank Vent

    I shortened my vent line and relocated my charcoal canister to the rear.
  14. KYNgsx

    4" Exhaust Build

    Thanks. The downpipe is as high as it can be before running into clearance issues from above with the subframe.My car is pretty low in the front, but the clearance came out pretty good. It's about the same as the 3" exhaust I had before. (I would have to report back later if you wanted...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top