1. Join the Community!

    DSMtuners is a massive archive of DSM information - but more importantly, it's a COMMUNITY! Join in and participate with other DSMers, and invite all of your DSM friends to make this place their home. Chat with others, create a build thread, post questions and answers. Get involved! Logging in will also remove many of the advertisements, along with this notice. ;)

John Mark Dongon's Recent Activity

  1. John Mark Dongon

    John Mark Dongon replied to the thread What bolts for flywheel cover housing?.

    Thanks!!!! See more

    Mar 19, 2019 at 11:45 PM
  2. John Mark Dongon

    John Mark Dongon liked DSMPT's post in the thread What bolts for flywheel cover housing?.

    Green: M6 x 1.0 x 10mm or M6 x 1.0 x 12mm Washer Assembled Part# MF140722 Qty: 2 or MD012109 Qty: 2 Yellow: M6 x 1.0 x 12mm Washer Assembled Part# MF241223 Red: M8 x 1.25 x 12mm Part# MF140021... See more

    20190319_162801-1.jpg Mar 19, 2019 at 11:45 PM
  3. John Mark Dongon

    John Mark Dongon posted a new thread.

    What bolts for flywheel cover housing?

    Anyone know?[ATTACH] See more

    20190319_162801.jpg

    Forum: Maintenance & Repairs

    Mar 19, 2019 at 6:31 PM
  4. John Mark Dongon

    John Mark Dongon posted a new thread.

    Does 4g63 turbo use same torque specs as 4g63?

    I only found 1 good source for the 4g63 turbo torque specs.. Everything else I found only says 4g63, I'm guessing they use the same torque specs right????? See more

    Forum: Maintenance & Repairs

    Mar 17, 2019 at 4:24 AM
  5. John Mark Dongon

    John Mark Dongon replied to the thread Is my cylinder head ok?.

    It's from the previous owner I only had the car for about a month before it started to make a constant knocking noise. As my uncle inspected the car we noticed the coolant tank was empty so I've... See more

    Mar 14, 2019 at 3:47 AM
  6. John Mark Dongon

    John Mark Dongon liked hopwoodp's post in the thread Is my cylinder head ok?.

    I’d do what Pauleyman suggest. I was there with a 2g head not long ago. I checked for flatness in accordance with the manual, it was out of spec. I took a decent 1g head and had it worked. Spent... See more

    Mar 14, 2019 at 1:20 AM
  7. John Mark Dongon

    John Mark Dongon attached a file to the thread Is my cylinder head ok?.

    I didn't sand too much and one of the pistons was chipped upon disassembley so i think that's what caused the detonation. So it should be ok to use in this condition despite the detonation? See more

    20190313_230233.jpg Mar 14, 2019 at 1:04 AM
  8. John Mark Dongon

    John Mark Dongon liked DSMPT's post in the thread Is my cylinder head ok?.

    You should check the flatness before sand it. it would be depending on the result. Check it as below. If the flatness is within the spec then it would probably be fine if you use a composite... See more

    Head flatness.jpg Mar 14, 2019 at 12:37 AM
  9. John Mark Dongon

    John Mark Dongon posted a new thread.

    Is my cylinder head ok?

    [ATTACH] [ATTACH] [ATTACH] Im on a budget and decided to resurface using sand paper. The problem is when I shine a flashlight I can see very little indents across the surface. Is this bad or is it... See more

    20190313_183225.jpg 20190313_183225.jpg 20190313_183225.jpg 20190313_184054.jpg 20190313_175235-1.jpg

    Forum: Maintenance & Repairs

    Mar 13, 2019
Support Vendors who Support the DSM Community
Ace Race Parts Archer Fabrication Best Used Tires Boostin Performance ECM Tuning ExtremePSI Feal Suspension Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications OHM Racing RockAuto SouthBay Fuel Injectors STM Tuned Tire Rack VR Speed Factory White Shed Speed