The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Morrison Fabrications
Please Support Rix Racing

Recent content by jdm9221

  1. Wtb Link V1 cable

    Wanted 2g Wtb Link V1 cable

    As the title states I’m hoping to buy a 2g DSMlink V1,V2 cable. I recently purchased an old school build still utilizing V1. The car now runs but most definitely needs some adjustments however I unfortunately did not receive a cable. Long term I’m hoping to use the trade up program thru Ecmlink...
  2. 2G DSM Link V2 & Cable

    Question by 'jdm9221' on classified ad '2G DSM Link V2 & Cable'

    Still available?
  3. jdm9221

    I mixed the rod caps

    this is hard to explain. The rod is in right,the rod cap goes to the right rod,does the e on the rod cap face the front or is it on backwards
  4. jdm9221

    I mixed the rod caps

    Which side. I put two with the E facing forward and two facing the back. Which is right?
  5. jdm9221

    I mixed the rod caps

    so I have the rod caps on the right rods but I apperently flipped two of them around and I’m not sure which is right. Does the E go towards the front of the car or rear?
  6. jdm9221

    Piston ring gap

    hey guys so here’s my question. I’m running a 6 bolt block with 1g rods and 2g pistons, i ordered a set of npr piston rings but I need to know suggested gap size for the top and bottom ring? Also I don’t need to space the oil rings correct? I’m running 23lbs of boost making about 350 and I do...
  7. jdm9221

    EVOscan High idle after driving

    so basically I have two questions in one. First off when I start the car it idles right around 1k rpms just fine but just recently as soon as I start driving it and come to a stop at say a stop light it idles at 2500 and doesn’t come back down,any ideas?Second is occasionally when I floor it I...
  8. jdm9221

    Misfire after adjusting cas

    So I set the timing light to 0 and grounded timing thru evoscan. The car runs fine when first started but when it warms up it starts misfiring again
  9. jdm9221

    EVOscan Car bogging and rpms drop during wot

    During a wot third gear pull the car is super sluggish and at wot the rpms drop for a second and barely climb back up. Ecuload is steady at 159,Idc is 80%,the car feels like it's Misfiring while driving but in boost or at idle it's fine. Any ideas or recommendations on a cheaper remote tuner who...
  10. jdm9221

    Misfire after adjusting cas

    So set the advance on the gun at 0 and evoscan at 5
  11. jdm9221

    Misfire after adjusting cas

    i have a 7 bolt head with a 1g cas. I grounded timing to 5° through Evo scan and used a timing light set to 5° And adjusted the cas til the marks lined up perfect when it flashed. I took the car for a drive and now its misfiring. It ran great last week,pulled it apart for a new timing belt(yes...
  12. jdm9221

    ECUflash Excessive knock and crazy backfire

    Copper plugs at .22 Never stated any intentions of trying to change the tune myself. I've already been looking for someone to tune the car
  13. jdm9221

    ECUflash Excessive knock and crazy backfire

    I can log another pull while logging load but I don't wanna hurt the car for sure. Lmk if you want another one because I wasn't logging load at the time
  14. jdm9221

    ECUflash Excessive knock and crazy backfire

    I'll consider it a possibility but I would assume I'd have a lot more signs of a bad rod bearing
  15. jdm9221

    ECUflash Excessive knock and crazy backfire

    I pulled the old knock sensor out and put the new one right back in
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top