The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support RTM Racing
Please Support Fuel Injector Clinic

Recent content by jazzyjay

  1. Who is running QM Gear-Drive HD Clutch Disks?

    I do have all in place, but explain
  2. Who is running QM Gear-Drive HD Clutch Disks?

    I can only find it on TMZ's website, who else sells upgrade parts? Who has the best price? What's the parts number?
  3. Who is running QM Gear-Drive HD Clutch Disks?

    Who is running the QM Gear-Drive HD Clutch Disks ? Is it worth the upgrade? I just dropped my tranny to find all the teeth stripped out of one of the disk. :hmm: Wish I could have the center replaced as the disk only has DYNO time on it. If I switch will I have more longevity. I think the...
  4. Quickest bike on the site.

    8.90 1/4 :hellyeah: 7 psi E85 enough said
  5. Real proof cheap FMICs are better than stock SMIC?

    Water to Air Intercoolers at FROZENBOOST.COMhttp://www.procharger.com/intercooled.shtml
  6. 7 bolt 4g64 with bolt head

    Yes I did my son currently has it at colleage with him. The car looks stock and dpendable, the only key that it has all the mods is that is that it has no MAFS. The Car made 430 whp before I saved tune and retuned to 290 whp. He enjoy the music more than speed(better for my pocket).
  7. Anyone in the military?

    I have been in the Army for 15 years, was a SFC 25B. I just finished WOBC I'm a 250N. Seven more years at tthe most to go:hellyeah:
  8. 7 bolt 4g64 with bolt head

    Ok just got the car back from paint. What is the fel pro part # for the head gasket for the 2.4 DOHC
  9. what size drag radial or slick

    So it fits properly without spacers, also is your car lowered?
  10. what size drag radial or slick

    What size drag radial or slick are you guys using on 16" rims.
  11. Clutch engagement different when turning left???

    I don't know if you have fixed the problem or not but I had this problem in my son's car. What happen is the the tranny bell housing had cracked and would separate will turning. I see that you just installed the tranny, so check the bolts holding the tranny to engine(do a good inspection).
  12. copmpression issue! could it be cams??

    Did you have head work done? If you have oversized valves and the machine shop cut the valve seats to have them sit in the head like the factory valves, the problem might be the length of the valve stem. I have a head that I made over 500 whp that had the same problem, I adjusted it with cam...
  13. 7 bolt 4g64 with bolt head

    Ok you are correct, I went through my Paypal and I do have a 4g64 headgasket but you can get 86.5 4g63 head gasket from several places Pueter.com and slowboy being a couple of them(if it's not on site just call). You are correct the part numbers for the rods(didn't say they where different) and...
  14. Scale values for 1200cc AfI injectors

    RC Eng 1200cc 10v - 2500 12v - 2000 14v -1620 16v -1320FIC 1200cc 10v - 2300 12v - 1650 14v - 1300 16v - 1020
  15. Scale values for 1200cc AfI injectors

    If you have dead time values for any size injector please post. This is a important step for anyone using a stand alone system. They have been alot of new injectors put on the market and the ECU makers don't have all of them in the software so they have to be input manually
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top