The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support ExtremePSI
Please Support Morrison Fabrication

Recent content by jamel16

  1. jamel16

    1Gb Talon Rust Revival

    Be careful with those wago type connectors. I had my aem gauges wired up in a similar fashion with those type of connectors and kept popping fuses. I couldn’t figure out for the life of me what was going on. Even went as far to rewire the entire panel with new aem gauge harnesses. Only to find...
  2. JM Fabrication stock flange, placement manifold
    Sold

    For sale 4G63 JM Fabrication stock flange, placement manifold

    I have a JM Fabrication stock placement manifold for sale in excellent condition. As you know this manifold is discontinued now, and has maybe 500 miles on it. This is perfect for stock flange turbos such as fp green, red etc. I also sent this back to JM Fabrications last year to have the welds...
    $675.00
  3. jamel16

    ECMlink Pesky idle surge

    Thank you, I will try it out in the
  4. jamel16

    ECMlink Pesky idle surge

    I checked all lines visually and with a smoke test.
  5. jamel16

    ECMlink Pesky idle surge

    Here are two of the logs, I was adjusting things, so it might look wonky.
  6. jamel16

    ECMlink Pesky idle surge

    I have a situation, so this is for all you geniuses out there. I have a pesky idle surge that I cannot diagnose. I’m not sure if it’s mechanical or tune related.This is a new build , so I’m trying to stabilize my idle before its first drive. I have done a boost leak test, smoke test, verified...
  7. jamel16

    Interest in bolt-on external wastegate O2 housings?

    Im onboard, recirculated version for FP30 housing.
  8. jamel16

    Street Build Project 1g (NBA DSM)

    First start, alternator belt making noise because I put the water pump pulley on backwards.
  9. jamel16

    Street Build Project 1g (NBA DSM)

    Finally started installing components back on the long block in preparation for the first start. Ditched the FIC 1100’s for 2150’s and also started some fab on a 3in cold air intake. Next on the list is to install the interior and finish the stereo.
  10. jamel16

    Street Build Project 1g (NBA DSM)

    Since I’m running a ball bearing unit, I decided to try out the turbosmart OPR unit with filter. It regulates turbo oil pressure to 40 psi. The next issue I tackled was fueling. The connections on my fuel hangar was crusty, so I replaced it with a radium engineering hardware. I wasn’t happy with...
  11. jamel16

    Street Build Project 1g (NBA DSM)

    Finally the long block was going back in , careful not to chip the new paint(even though I did). Once in, I started redoing all my ground and power cable. I was running some trash wire, so that needed to be addressed. I also got that ethanol sensor mounted and fuel line routed.
  12. jamel16

    Street Build Project 1g (NBA DSM)

    Jeesh I know this is due for an update, so let’s begin. I started by adding components back to the bay, my biggest task was redoing all my brake lines. After about 30 ft of Nicop tubing, I finally finished with something presentable. Next was mounting the Wilwood clutch master cylinder.
  13. jamel16

    1G Excessive amperage issues running Walbro 525 fuel pump.

    So I’m having a dilemma, on my new build I’m planning on running E85 majority of the time. So I revamped my fuel system with FIC 2150cc injectors, Walbro 525 pump, and redid my fuel pump rewire with 12-10 gauge wiring and 40 amp Bosch relay. My question is has anyone ran into excessive current...
  14. jamel16

    Shootout 2024 scramble

    Very interested in this conversion, do you think it can work on a 1g?
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top