The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Morrison Fabrication

Recent content by Jacolu3

  1. Jacolu3

    Ready for 9s

    I'm using a pedal from a 2006 mitsubishi eclipse. I got it pretty cheap on eBay.
  2. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    I did not sand down the clear coat on my carbon hatch. I just cleaned the surface and used a lot of 3m fast cure auto glass urethane and haven't had any issues in 2 years.
  3. Jacolu3

    Ready for 9s

    Did a little upgrading over the winter Haltech elite 1500 with a bosch 68mm DBW throttle body Kiggly 12 tooth crank trigger Magnus intake manifold and a haltech IC-7 dash
  4. Jacolu3

    Ready for 9s

  5. Jacolu3

    Ready for 9s

    It wasn't that bad. With the ohm racing fuse box relocation wiring harness it was pretty easy. Took about a day
  6. Jacolu3

    Drive By Wire - Haltech How-To

    I ended up cutting the mounts off the pedal so it would sit flush on the firewall. I used one of the factory studs and a rivnut on the bottom. Worked out pretty good.
  7. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    Well the haltech has a plug and play adapter which makes wiring very easy. And haltech has lots of tech info on the web and they are very helpful over the phone too.
  8. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    So I just finished doing this with a haltech elite 1500. I don't think ecmlink would be capable of doing this. The pedal gets wired in directly to the ecu and the throttle body also gets directly wired into the ecu. They actually don't get wired together. The pedal will have 2-5v wires...
  9. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I attempted to mount my 3g pedal this weekend and I didn't like how it wasn't going to sit flush on the floor boards. I ordered a 1" thick piece of aluminum that is the same width and length of the pedal. I will have to try to fab something up with it so the entire pedal has a flat surface to...
  10. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I'm planning on mounting it this weekend. I'm going to try use rivnuts to mount it. If it works out good I'll post some pics this weekend
  11. Jacolu3

    Drive By Wire - Haltech How-To

    I plan on mounting mine this weekend with rivnuts. If it works out I'll post some pictures
  12. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    I've had mine for almost 2 years and still looks brand new. I have mine installed in a carbon fiber hatch and would highly recommend it.
  13. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    This seems to be right. The colors match for 5 of the 6 wires. Thank you!!!!
  14. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I'm switching to a bosch dbw throttle body with a 2012 eclipse pedal assembly. I have the factory plug but I can't find a wiring diagram for the pedal.I was wondering if anyone has a wiring diagram for a 4g eclipse or knows the pinout for the pedal?Thanks Brian
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top