The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Fuel Injector Clinic

Recent content by gIGoN

  1. Can i make 600awhp on pump gas?????

    At my place we have ron100 from shell. Would this help to reduce knocking say if i would want to boost >30psi? I would also want to see if pump gas could go beyond 600hp.
  2. EVO III Vehicle speed sensor / wiring

    Good news. I did the 3rd step you mentioned, my reed switch is working fine. So what i did was i connected an ring connected to a wire to the screw on the top right (looking from behind the cluster) which is beside the left signal and pulled it directly to pin #66 and thank god it worked.My...
  3. EVO III Vehicle speed sensor / wiring

    I decided to open up the cluster and found this 2 pins which connects to the whole speedo section in the cluster meter:From the back of the cluster the 2 pins are tighten by 2 screws. Can i just connect a round ring terminal to these 2 screws? 1 goes to the ecu and one goes to the ground...
  4. EVO III Vehicle speed sensor / wiring

    Traced and all the black wires frm both blue and brown are conected together. Did a continuity test and all the wires are grounded fine. Not cuts on the wires or whatsoever.
  5. EVO III Vehicle speed sensor / wiring

    None. Based on reading in the link ecu. Theres no frequency at all coming out from that wire. Ive tried on 2 different clusters so i dont think the cluster meter is the issue though. Would there be anything else i hv missed or should check to get the reading?
  6. EVO III Vehicle speed sensor / wiring

    using a multimeter, so the wire from the ecu is ok up until the cluster's blue socket. I tried swapping the cluster meter and there's still no reading as i believe it should be generated by the dash cluster meter.
  7. EVO III Vehicle speed sensor / wiring

    just an update guys, the speedo is actually the centre pin on the blue socket. i did a continuity test and the cable is connected up until the ecu. I'm still not sure why theres still no reading at the ecu.i've tried using a different cluster meter and its still not getting any reading to the...
  8. EVO III Vehicle speed sensor / wiring

    Thanks for the reply. when you say cluster, you mean that it's from the back of the speedometer? The one with the blue and brown sockets?Can i pull a new wire and connect it directly to the ecu?There's actually a few green and yellow. Do you happen to know which one (location) is it from...
  9. EVO III Vehicle speed sensor / wiring

    I did a continuity test and there is a connection from the socket up to the ecu. I am still clueless where it gets the speed reading from. Hope someone could shed some lights on this.
  10. EVO III Vehicle speed sensor / wiring

    I traced the wire from the ecu and it goes to this socket. Where does this connect to?Traced it again and this socket goes to the column shaft socket (the black thingy which has the wiper and light arms near the steering. Noticed there's some board inside it connects to. I’m lost after that...
  11. EVO III Vehicle speed sensor / wiring

    Thanks for the reply. Which wire exactly is it from the meter cluster?
  12. EVO III Vehicle speed sensor / wiring

    Hi guys,I'm trying to figure out where is my speed sensor. I have a CE9a EVO III. The speedometer cluster gets the reading via a cable which goes to the gearbox. So I'm wondering the vehicle speed sensor which goes to the ECU is reading the speed from which sensor as the speedo is only a cable...
  13. Power window wiring

    Figured out the wires and the relays. Just need to confirm if each window motor needs 2 relays or it can be shared
  14. Power window wiring

    Hi guys,Need help for power window wiring. Im setting up a new set of wiring with relays and how to go about as to which wire goes where.My driver side has the switches for all windows and each door has their own switches.1. Do i need relays on each of the switches at the doors? 2. Based...
  15. #NTRR

    was wondering why the switch from borg warner....was that the s476sx-e?
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top