The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support ExtremePSI
Please Support ExtremePSI

Recent content by dsmBear

  1. dsmBear

    1G Questions about boost leak test

    I can't even boost 7 pounds with out a leak lol its a fat leak, and because I did injector seals twice now, and it's the only thing I can think of. The leak sounds like it's coming from around manifold and I've used plenty of soap water but still nothing
  2. dsmBear

    1G Questions about boost leak test

    Ive been tracking down this boost leak, it seemed like injector seals but I've done those twice now cleaning all the ports new seals and o rings and insulators, but it still leaks from somewhere around the manifold, I was wondering, could I remove the fuel rail and injectors and use little...
  3. dsmBear

    Doing a restoration on a 1990 Talon TSI AWD

    16g you mean? 16g On a healthy motor on low boost should be around 210-220hp
  4. dsmBear

    1G my axle snapped

    Can you post pics of new axle, my awd front axles at orielly were 65 each. I'm sure they have a fwd one too, I would return it if it has no cotter pin hole. Call a few stores and just see if they can get the seals Alsohttp://www.streettunedmotorsports.com/parts/oem_dsm_front_axle_seals_fwd.htm
  5. dsmBear

    1G my axle snapped

    EDIT: Just realized yoy have an auto, that seal is for a manual, I have no idea if the seals are same or not. Skf part numver is 14006, they're around 10 bucks, 5 online if you want to leave your car in a random lot for few days. I also used a 32mm socket and half inch breaker bar to press the...
  6. dsmBear

    1G my axle snapped

    Unbolt the axle nut, if it's awd remove the bracket thats ib the way it's like 5 bolts, Sna axle out of trans, then pull until shaft is outside of tranny, then hammer with a rubber mallet the side where the castle nut was and done. I'd replace the axle seal as well. I know from expeirence, 2...
  7. dsmBear

    1G 3-4k idle afer manifold gasket swap

    Yeah I scraped off the old gasket no rtv though as it was a metal gasket, I did a boost leak test whuch no conclusive results I'm on the stock bcs and it held 7 pounds and no hissing noises or bubbles
  8. dsmBear

    1G 3-4k idle afer manifold gasket swap

    Yeah its at .63, I played with the throttle cable a bit, now it idles 1-2k, before I had a little idle surge like 1-1.2k but now it's even worse,
  9. dsmBear

    1G 3-4k idle afer manifold gasket swap

    My intake manifold gasket was destroyed, couldnt even build boost, swapped with a machv metal one, builds boost and holds just fine and starts right up but it idles at 3600-4k , i have the biss screw all the way down, and everything is plugged in. i checked the throttle cable and its not caught...
  10. dsmBear

    1G Melted intake gasket?

    So i had a huge boost leak (on stock bcs, spooled up to 5 psi feeling like nothing and could hear the whistle), it was coming from around manifold area, i have a rebuilt tb with new seals and gaskets, new injector seals and o rings, new oem fuel rail bolts, but it still leaks so i say f*** it...
  11. dsmBear

    1G Boost leak at maf

    yeah well my boost gauge does, and ok yeah that makes sense feel kind of stupid now but yeah my boost gauge holds at whatever psi i out it in, but when driving, espeically when cold you can feel and hear the boost leak
  12. dsmBear

    1G Boost leak at maf

    Well I have a bad boost leak like I can hear it and feel it. I have no other leaks if I hook up the coupler directly to turbo
  13. dsmBear

    1G Boost leak at maf

    Sounds like from where the air filter is, but I can't feel it or see it, I do have an extra filter I can throw om and try
  14. dsmBear

    1G Boost leak at maf

    I did a blt, and found 2 leaks at intercooler couplers, I fixed them, did the blt again and leaks gone. Next day I start up and drive but it still feels like a massive leak. Me being lazy and not wanting to remove the intake and my catch can and small coolant bottle, I made a mini tester that...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top