The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Morrison Fabrication

Recent content by dgdsm

  1. 2G Diagnosing the diagnostic port

    Has anyone ever disassembled a Mitsubishi OBD-II port ? Something like this https://www.youtube.com/watch?v=8LlyxpCPbNQ ?In mine, it looks like things are held in place by a white piece of plastic fitting into a black piece that has the actual female terminal pins.
  2. Spyder P0302 and fuel injectors

    Right, I was referring to the injector insulator. Thanks. The injectors are basically the same across the two part #s, or at least they are supposed to be. The appearance and colors of the exterior are a little different. I don't recall having as much trouble as I did with the seating of the...
  3. Spyder P0302 and fuel injectors

    No CEL !!!! Apparently P0302 is a code that goes away after 3 drive cycles without P0302 symptoms. Now a decision to make on what do with these injectors. They may make a great set of injectors for someone for DD use by replacing the lower o-rings.
  4. Spyder P0302 and fuel injectors

    I recently did a fuel injectors replacement and ended up with a P0302 (cylinder #2 misfire) with all kinds of driving symptoms associated with single cylinder misfire (and possibly running on 3 cylinders).Well today I went back to my old injectors and found the problem: A cracked O-ring...
  5. 2G DOT-3 as clutch fluid?

    I've been recently experiencing some strange clutch shifting symptoms, that I concluded was mainly about old/ exhausted clutch fluid. It's been the same fluid in there for 5+ years. Today I took out what was in the reservoir and replaced it with some SMB DOT-3 that I had around, which is...
  6. 2G 95 TSI started tapping/knocking

    Did you have a look at the white marks left by whoever worked on the TB last time? Your timing belt has skipped a tooth.
  7. 2G 95 TSI started tapping/knocking

    I could come by and make a visit to your dsm, and discuss possible options. Left you a PM.
  8. 2G Front roll stopper mount bracket (part #/ torque ?)

    Thanks for the responses and info. @Mello those look like min and max numbers. Correction I see it's ft-lbs and Nm. Thanks again.
  9. 2G Front roll stopper mount bracket (part #/ torque ?)

    Today I replaced my front engine roll stopper mount (rubber was broken and falling apart). To get all the holes to line up correctly, I temporarily loosened the 17mm bolts that attach the roll stop mount support bracket to the transmission. Does anyone know the name of this part (or part #)...
  10. 2G Engine won’t crank

    You could also take the starter out of the vehicle and (bench) test it to make sure it's working correctly. There's lots of YT videos on it.
  11. 2G Alignments and eccentric toe bolt

    When I look at the diagrams from the FSM, it looks like there is only one mating mark at the bottom, so the expected position would leave all those notches on the right side and closer to the bottom than the top (hope that makes sense). But it may just be at one end of the adjustable range...
  12. 2G Alignments and eccentric toe bolt

    So after chewing through rear tires for about 5 years, I have now started to do my own alignments. I'm using two methods, the toe plate method and a laser level method I found on YouTube. I might also do a string alignment sometime. Both the front and the rear are now within specs (0.06 inch...
  13. 2G 4g64 Swap, Model years?

    There's probably someone on this forum who knows more, and there are some threads out there on this subject. Here's one . You need to think about how the block hooks up to the transmission, and also how the head hooks up to the intake etc, since the 4g64 in the 3g is in the opposite...
  14. 2G M/T - tire size difference ?

    I assume you mean premature wear on the differential components in the transmission? If so I'm wondering how bad the stress on it would be, or if it's ok to leave it like that for a few months. I've always had minor noise symptoms going into 1st and 2nd gear and it's gotten a little worse in...
  15. 2G M/T - tire size difference ?

    What are the consequences of running different tire sizes on an M/T vehicle? What I have is an F5M31 (4G64), and currently there is a 205/55/16 on the front driver side wheel and a 205/60/16 on the front passenger side wheel. It's quite a large difference according to the tire size calculator...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top