The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Kiggly Racing
Please Support STM Tuned

Recent content by Casem13

  1. Casem13

    2G Possible spun bearing?

    Thank you for the help. I’m just going to sell the car instead. Not worth the money to throw into it anymore.
  2. Casem13

    2G Possible spun bearing?

    Yea I don’t care if it’s new or used. I’ve been looking through classifieds for evo3-9 crankshafts as well. It’s pretty slim pickings
  3. Casem13

    2G Possible spun bearing?

    Do you know any place to get a crankshaft used or even reman? The auto parts around here can’t get them and there are no wrecking yards either with the part. Online they are around $600-$800
  4. Casem13

    2G Possible spun bearing?

    I did forget to mention that the oil pressure was fine after installing the bearings, but there was a slight knock. But the knocking has gotten worse and now the oil pressure is peaked out but still getting to the top end without issue. I know the bearings are not in backwards. I checked them...
  5. Casem13

    2G Possible spun bearing?

    I recently had issues with crankwalk. I checked and the main middle bearing with the thrust washer was shaved down on one side. The crankshaft has mild scratching on the side that wore down the bearing. I replaced the Main bearings and the crank position sensor because it was bad due to the...
  6. Casem13

    2G Lowering spring question

    I know if I don’t go past like 1.3 inch drop I shouldn’t need a camber kit due to it not being lowered much. I’m not trying to go super low because that’s tacky and ridiculous. Just trying to close the gap some in the wheel wells
  7. Casem13

    2G Lowering spring question

    Yeah I’ll have to check around. A long time ago I made the mistake of buying ones for a non-turbo and it was supposed to do a 1 inch drop but it sent me car straight to the ground so I sent them back. I found one of the vendors on here sells lowering springs that it lists for gst/ gsx so I’ll...
  8. Casem13

    2G Lowering spring question

    I just want a good pair of lowering springs that work for the gsx due to the extra weight
  9. Casem13

    2G Lowering spring question

    I’ve seen posts like this a bunch and they all have the same answers. Here is the issue. I’m trying to get lowering springs for my 97 gsx. I already have Koni yellows, but I’ve been trying to find lowering springs. I wanted to get the eibach prokit. But it’s no longer made, same with H&R...
  10. Casem13

    For Sale WTB 23 spline output shaft

    I need an output shaft for my 1997 Eclipse gsx. I’ve been having a hard time finding one. Preferably good used one. It’s too expensive for a new one. Thanks
  11. Casem13

    motor binding won't crank by hand

    Had the same issue. Ended up being stuck piston rings from sitting so long
  12. Casem13

    2G Rear motor mount bracket question.

    Yea I seem to have misplaced my original one
  13. Casem13

    2G Rear motor mount bracket question.

    It’s ok. Thanks for the help. This is the one I need though. http://performancepartout.com/2g-rear-manual-transmission-bracket-087/
  14. Casem13

    2G Rear motor mount bracket question.

    Yea that’s not the mount part I need. The one that I need says it’s out of stock. But thanks though.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top