The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Fuel Injector Clinic

1G Can you name this intake manifold?

This site may earn a commission from merchant
affiliate links, including eBay, Amazon, and others.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

It's a dejon tool. Was built in the late 90's most likely. Yeah, it's heavy, but I bet it would suprise you at the power it will make. I have one I've been meaning to try out.
This thing is definitely heavy. I will have to blast it down because its steel & has rust within. It shouldn't take much to get it cleaned. The vehicle supposedly was making around 700, this wasn't on it tho when I picked up the car. It was inside with a bunch of other parts.
 
That flood car was a good pick up. It had decent usable parts for the price.
Yeah, the owner really hooked me up. I received a complete spare motor as well, auto trans, and a clean 4g63 1g head, plus whatevers included in the build from the tsi. I'm just not familiar with all of this & was in the middle of picking out some piston/rod combo to finish my gst. Now I'm not sure if I have a 6bolt now & maybe not use the 7bolt na I had available. These aren't bad problems tho. I've been reading nonstop on this forum for the past 2 months straight. You guys are a huge help
 
Yeah, the owner really hooked me up. I received a complete spare motor as well, auto trans, and a clean 4g63 1g head, plus whatevers included in the build from the tsi. I'm just not familiar with all of this & was in the middle of picking out some piston/rod combo to finish my gst. Now I'm not sure if I have a 6bolt now & maybe not use the 7bolt na I had available. These aren't bad problems tho. I've been reading nonstop on this forum for the past 2 months straight. You guys are a huge help

Not a bad problem to have at all. This site is da best!! Fyi I would’ve jumped on the flood car if it was closer. :sneaky:
 
Not a bad problem to have at all. This site is da best!! Fyi I would’ve jumped on the flood car if it was closer. :sneaky:
i crossed state lines, 8hr drive forward/back, rented a trailor, & filled up twice. my eclipse was the same hrs but within Texas (fort worth)... i can't find anything within houston.:idontknow: : i definitely have dsm fever now:talon::dsm::thumb:
 
i crossed state lines, 8hr drive forward/back, rented a trailor, & filled up twice. my eclipse was the same hrs but within Texas (fort worth)... i can't find anything within houston.:idontknow: : i definitely have dsm fever now:talon::dsm::thumb:

8 hours :applause: that’s not a fever, that’s an issue and you need help. ROFL
 
This thing is definitely heavy. I will have to blast it down because its steel & has rust within. It shouldn't take much to get it cleaned. The vehicle supposedly was making around 700, this wasn't on it tho when I picked up the car. It was inside with a bunch of other parts.

Do not blast it. It would be impossible to clean all the grit out of it. Use a chemical rust stripper to clean it. .
 
idk, that might not be a dejon. Mine is shaped a little different. Might be a 1g head on a 2g car version.
I believe the motor has a 2g head on a 1g bottom end.(6bolt) I'll be pulling the motor within the next day or two. Do you honestly think I could still produce some numbers with this manifold? I've never seen anything like this besides the JMF design.
 
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

Back
Top