The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support ExtremePSI
Please Support ExtremePSI

How does this happen to a throttle body?

This site may earn a commission from merchant
affiliate links, including eBay, Amazon, and others.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

enriquez2000

Proven Member
2,269
810
Oct 5, 2014
fort collins, Colorado
Working on a customer car and had a 2k idle and couldnt find any leaks.... pulled throttle body off and see this huge gap... makes sense now.

Is this a rebuild gone wrong? Ive never seen one come off a car like this... usually carbon build up at best holding it cracked.
 

Attachments

  • 20180915_103910.jpg
    20180915_103910.jpg
    168.8 KB · Views: 117
  • 20180915_103918.jpg
    20180915_103918.jpg
    165.6 KB · Views: 105
Throttle plate is installed flipped & not in proper orientation. The edge on the throttle plate is not right angle square, it slightly angle for when the plate is in the close position. Fix is removing the plate and flipping it around until angled edge mates up to the TB throat in the close position.
 
So they point it in backwards and crooked. Ill flip and realign for them. It also has no throttle stop(sensor). That shouldnt matter though I wouldnt think for high idle
 
You'll need to add something for a throttle stop so the plate doesn't stick when fully closed.
 
It's hard to say exactly how it's orientated now. could be flipped front to back, rotated 180 degrees, or both. When I'm trying to sort out a "basket case" TB plate I add a mark for a point of reference & test it in different orientation with the screws removed but the hole visually lined up. When you get it correct the plate fits proper, opens & closes & won't stick or bind, & then add the screws. It's easy to tell when its in correctly.
 
It's hard to say exactly how it's orientated now. could be flipped front to back, rotated 180 degrees, or both. When I'm trying to sort out a "basket case" TB plate I add a mark for a point of reference & test it in different orientation with the screws removed but the hole visually lined up. When you get it correct the plate fits proper, opens & closes & won't stick or bind, & then add the screws. It's easy to tell when its in correctly.
Alrighty... sounds like a good time LOL
 
This doesn't really take a lot of time & it's easier with the return springs unhooked or removed.
 
This doesn't really take a lot of time & it's easier with the return springs unhooked or removed.
Ya just a pain when not done rightthe 1st time... they put this iac on.... little worried what else is hidden.

Long story short car came from a guy who got fed up with the shop that was working on it. So far ive had to rewire gauges hooked to headlights and sensors that were hacked into the harness. Thus car is why people say dsm is unreliable.

I on the other hand have a 93 that I daily 300 miles a week with barely any issues.
 

Attachments

  • 20180901_143709.jpg
    20180901_143709.jpg
    215.1 KB · Views: 37
I just finished a car for a guy that wouldn't idle below 2k worth a damn. I pulled his tb off and same thing. His buddy rebuilt and ported it and got into where the plate seats and caused it.
 
I just finished a car for a guy that wouldn't idle below 2k worth a damn. I pulled his tb off and same thing. His buddy rebuilt and ported it and got into where the plate seats and caused it.
Hopefully its not trashed and just put together wrong. If it is he can track one down I guess
 
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

Back
Top